Recalls that may apply to the 2014 Mazda CX-5
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
By component
| 16V644000 | 2016-09-06. STRUCTURE:BODY:HATCHBACK/LIFTGATE. Mazda North American Operations (Mazda) is recalling certain model year 2010-2013 Mazda3 and Mazdaspeed3 vehicles manufactured November 18, 2008, to June 8, 2013, 2012-2015 Mazda5 vehicles manufactured October 26, 2010, to June 22, 2015, 2016 CX-3 vehicles manufactured June 1, 2015, to December 26, 2015, and 2013-2016 CX-5 vehicles manufactured December 15, 2011, to December 26, 2015. On the affected vehicles, the lift gate support struts may corrode, possibly causing the struts to break and/or the lift gate to drop unexpectedly. Built 2011-12-15 to 2015-12-26. |
|---|---|
| 16V203000 | 2016-04-11. STEERING. Mazda North American Operations (Mazda) is recalling certain model year 2016 CX-3 vehicles manufactured June 1, 2015, to December 2, 2015, 2013-2014 Mazda2 vehicles manufactured July 3, 2013, to August 8, 2014, 2014-2016 CX-5 vehicles manufactured January 19, 2013, to December 2, 2015, and 2013-2015 CX-9 vehicles manufactured December 6, 2012, to July 31, 2015. The lower mounting nuts and bolts that attach the front strut assembly to the steering knuckle may loosen, allowing the steering knuckle to separate. Built 2013-01-19 to 2015-12-02. |
| 16V064000 | 2016-02-03. FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP. Mazda North American Operations (Mazda) is recalling certain model year 2014-2016 Mazda CX-5 vehicles manufactured June 27, 2013, to February 2, 2016. The affected vehicles have a fuel filler pipe that may rupture in the event of a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 301, "Fuel System Integrity." Built 2013-06-27 to 2016-02-02. |
| 2016431 | 2016-09-06. Structure. On certain vehicles, the anti-corrosion treatment of the outer tube of the rear lift gate stay may be insufficient. Over time, the outer tube of the rear lift gate stay may corrode and break off, which could increase the risk of injury. Correction: Dealers will replace both rear door stays. |
|---|---|
| 2016152 | 2016-04-08. Suspension. On certain vehicles, the nut and bolt holding the strut assembly to the knuckle may not have been tightened properly during the manufacturing process. Over time, this could cause the strut assembly to separate from the knuckle, resulting in a loss of steering control which would increase the risk of a crash causing injury and/or damage to property. Correction : Dealers will inspect and replace the nut and bolt holding the strut assembly to the knuckle if found loose. |
| 2016049 | 2016-02-01. Fuel System. Certain vehicles fail to comply with the requirements of Canada Motor Vehicle Safety Standard 301 – Fuel System Integrity. During rear impact crash testing, the fuel filler pipe ruptured, causing fuel spillage exceeding the limit specified by the standard. As a result, a collision involving the rear of the vehicle could result in a fuel leak. Fuel leakage, in the presence of an ignition source, could result in a fire causing injury and/or property damage. Correction: Dealers will remove a bolt on the left rear side member attaching the bracket to the fuel filler pipe. This will change the load path during a rear crash impact preventing filler pipe rupture. |
A campaign lists a year, a make and a model, and often only some of the vehicles built. A list with nothing on it is not a clearance either. The lookups below check one VIN.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.