Service bulletins for the 2014 Mazda CX-5
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
789 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| 01-014-15-3055A | 2017-06-08. Service bulletin. ENGINE. FREQUENT ENGINE STARTS UNDER EXTREMELY COLD AMBIENT TEMPERATURES MAY RESULT IN OIL SEEPAGE FROM THE ENGINE OIL PRESSURE SWITCH. THIS CONCERN MAY BE CAUSED BY A LACK OF DURABILITY OF THE OIL PRESSURE SWITCH UNDER THESE CONDITIONS. TO CORRECT THE PROBLEM, THE OIL PRESSURE SWITCH HAS BEEN IMPROVED TO INCREASE THE DURABILITY IN COLD AMBIENT TEMPERATURES. |
|---|---|
| 01-023-15-3084B | 2017-06-08. Service bulletin. ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. • P0015:00 - EXHAUST CMP TIMING OVER-RETARDED • P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME. |
| 01-023-15-3084A | 2017-06-08. Service bulletin. ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. • P0015:00 - EXHAUST CMP TIMING OVER-RETARDED • P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME. |
| 09-043-15-3106 | 2017-06-08. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; STRUCTURE:BODY. WHILE DRIVING OVER ROUGH OR BUMPY ROADS, SOME VEHICLES MAY EXHIBIT A RATTLE / POP NOISE FROM THE INSTRUMENT PANEL AND/OR A CREAK NOISE FROM THE A-PILLAR. RATTLE / POP NOISE FROM INSTRUMENT PANEL: THE RATTLE / POP NOISE MAY BE CAUSED BY LOW COWL PANEL (A) MOUNTING BOLT (B) TORQUE. |
| 05-001-15-3104 | 2017-06-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL). SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS: • SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) • HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR • SHIFT LEVER VIBRATES WHEN DRIVING IN 3RD OR 4TH GEAR THIS IS CAUSED BY INAPPROPRIATE TRANSMISSION INTERNAL PARTS. |
| 02-001-15-2998A | 2017-06-08. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; SUSPENSION:FRONT:CONTROL ARM:LOWER ARM. SOME VEHICLES MAY EXHIBIT A CREAKING NOISE FROM UNDER THE FRONT OF THE VEHICLE WHEN DRIVING OVER BUMPS. THE NOISE OCCURS AT APPROX. 12 - 25 MPH (20 - 40 KM/H) WHEN THE ROAD SURFACE IS WET OR AFTER A CAR WASH. THE NOISE BECOMES MORE NOTICEABLE WHEN DRIVING OVER HIGHER BUMPS. THE CREAKING NOISE IS CAUSED WHEN THE FRONT LOWER CONTROL ARM BUSHING(S) (A) BECOME WET. |
| 05-001-15-3104A | 2017-06-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL). SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS: • SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) • HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR • SHIFT LEVER VIBRATES WHEN DRIVING IN 3RD OR 4TH GEAR THIS IS CAUSED BY INAPPROPRIATE TRANSMISSION INTERNAL PARTS. |
| 05-002-15-3019E | 2017-06-07. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. NOTE: IF THE VEHICLE ALSO HAS A DELAYED ENGAGEMENT CONCERN, THIS TSB IS NOT APPLICABLE. REFER TO MS3 ONLINE INSTRUCTIONS OR WORKSHOP MANUAL FOR PROPER DIAGNOSIS AND REPAIR PROCEDURE. |
| 06-001-15-3054B | 2017-06-07. Service bulletin. STEERING. SOME VEHICLES MAY EXHIBIT AN UNUSUAL THUMPING NOISE FROM UNDER THE FRONT OF THE VEHICLE. THIS NOISE ONLY OCCURS WHEN STARTING TO MOVE THE VEHICLE WHILE THE STEERING WHEEL IS TURNED TO THE FULL LEFT POSITION. NOTE: THE NOISE WILL NOT OCCUR IF THE STEERING WHEEL IS IN THE CENTER OR FULL RIGHT POSITION. THE NOISE IS CAUSED WHEN THE EDGE OF THE LEFT SIDE INNER BALL JOINT GETS STUCK WITH THE STEERING GEAR HOUSING. TO ELIMINATE THE NOISE, THE SHAPE OF THE INNER BALL JOINT EDGE HAS BEEN CHANGED. |
| 09-039-15-3097 | 2017-06-07. Service bulletin. STRUCTURE:BODY:HATCHBACK/LIFTGATE. SOME VEHICLES MAY EXHIBIT RUST (A) ON THE LIFTGATE OPENING AROUND THE LEFT AND/OR RIGHT SIDE STOPPER (B). THE PAINT IN THIS AREA MAY BE THINNER THAN NORMAL DUE TO PRODUCTION VARIANCES. THE PRODUCTION PROCESS HAS BEEN IMPROVED TO ELIMINATE THIS CONCERN. |
| 04-005-15-3089 | 2017-06-07. Service bulletin. SERVICE BRAKES. SOME VEHICLES MAY EXHIBIT A SQUEAKING / GRINDING NOISE FROM THE REAR BRAKES. THIS NOISE MAY BE CAUSED BY THE WEAR INDICATORS OF PREMATURELY WORN OUTER REAR BRAKE PADS. NOTE: THE INNER REAR BRAKE PADS WILL ONLY SHOW A LITTLE WEAR. THIS CONDITION ONLY AFFECTS THE OUTER REAR BRAKE PAD(S). DURING USAGE OF THE VEHICLE IN AREAS WHERE ROAD SALT IS USED, THE OUTER REAR BRAKE PAD(S) MAY BECOME STUCK DUE TO CORROSION. THIS MAY CAUSE BRAKE DRAGGING AND REMATURE WEAR TO THE OUTER BRAKE PAD(S) ONLY.THE TREATMENT OF THE BRAKE PAD BACK PLATE HAS BEEN CHANGED TO ELIMINATE THIS CONCERN. |
| 09-041-15-3096 | 2017-06-07. Service bulletin. ELECTRICAL SYSTEM. SOME VEHICLES MAY EXPERIENCE ONE OR MORE OF THE FOLLOWING SYMPTOMS IN CONNECTION WITH A MALFUNCTION RELATED TO THE C-15 CONNECTOR. • THE DRIVER SIDE POWER WINDOW DOES NOT OPERATE. • THE DOOR DOES NOT OPEN WHEN USING THE ADVANCED KEYLESS SYSTEM. • THE WARNING LAMP STAYS ON EVEN AFTER THE IGNITION SWITCH IS TURNED OFF. • DTC B10E7:17 (START STOP UNIT, IG1 RELAY CIRCUIT MALFUNCTION) AND DTCS RELATED TO COMMUNICATION ERRORS MAY BE STORED IN PCM MEMORY. THE SYMPTOMS LISTED ABOVE MAY BE CAUSED BY CORROSION OF THE C-15 CONNECTOR TERMINALS DUE TO WATER INTRUSION THROUGH THE FRONT DOOR. IN LOW AMBIENT TEMPERATURES, THE DOOR HARNESS HARDENS. IF THE DOOR IS FULLY OPENED, IT MAY CREATE A GAP BETWEEN THE DOOR AND THE DOOR HARNESS GROMMET, WHICH MAY ALLOW WATER TO ENTER THROUGH THE GAP.MASS PRODUCTION CHANGES: • THE FRONT DOOR HARNESS GROMMET HAS BEEN CHANGED TO IMPROVE SEALING PERFORMANCE. • HOLES INSIDE THE FRONT PILLAR (WHICH ARE MADE FOR WEIGHT REDUCTION), HAVE BEEN COVERED TO PREVENT WATER INTRUSION. |
| 09-029-15-3062 | 2017-06-07. Service bulletin. EQUIPMENT:MECHANICAL. ON SOME VEHICLES, THE FUEL FILLER LID WILL NOT OPEN/CLOSE. THIS MAY BE CAUSED BY SNOW WITH ROAD SALT BEING BROUGHT INTO THE FOOTWELL AREA. THE MELTED SALT WATER THEN FLOWS ALONG THE OPENER LEVER (A) AND ENTERS INTO THE CABLE (B) CAUSING THE INNER-CABLE TO CORRODE AND SEIZE. TO CORRECT THE PROBLEM, A FLANGE HAS BEEN ADDED TO THE FUEL FILLER LID OPENER LEVER (A) TO PREVENT WATER FROM FLOWING ALONG THE LEVER TO THE FUEL FILLER LID CABLE. |
| 09-034-15-3068 | 2017-06-07. Service bulletin. SEATS:FRONT ASSEMBLY:POWER ADJUST; EQUIPMENT:ELECTRICAL. SOME CUSTOMERS MAY COMPLAIN THAT THE FRONT POWER (DRIVER AND/OR PASSENGER) SEATS DO NOT SLIDE BACK AND FORTH PROPERLY OR THAT THEY MAY BE COMPLETELY INOPERATIVE. THIS CONCERN MAY BE CAUSED BY A FOREIGN OBJECT GETTING STUCK UNDER THE POWER SLIDE UNIT (BELOW) WHILE IN OPERATION. THIS CAN CAUSE MOTOR MOUNTING BRACKET (A) DEFORMATION, RESULTING IN MOTOR CABLE (B) BREAKAGE. TO ELIMINATE THIS CONCERN, THE SHAPE OF THE MOTOR MOUNTING BRACKET (A) HAS BEEN MODIFIED TO INCREASE ITS STRENGTH. |
| 01-016-15-3067 | 2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0421:00 (CATALYTIC CONVERTER SYSTEM) WITHOUT EXPERIENCING POOR ENGINE PERFORMANCE OR MISFIRE (MITSUBISHI PCM ONLY). THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM THAT MAY DETECT FALSE ERROR OF THE A/F SENSOR, RESULTING IN FALSE DETECTION OF P0421. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED. CATALYST MONITOR FUNCTION EXPLANATION • THE PCM MONITORS THE OXYGEN STORAGE AMOUNT PROPORTIONAL TO CATALYTIC CONVERTER PURIFICATION CHARACTERISTIC. • THE PCM STARTS TO MONITOR AFTER RECOVERY (FUEL INJECTION STARTS) FROM FUEL CUT CONTROL. • THE PCM TEMPORARILY CHANGES THE TARGET AIR/FUEL RATIO TO RICH AT FUEL CUT RECOVERY, AND DETECTS THE RESPONSE TIME UNTIL THE HO2S OUTPUT SIGNAL OUTPUTS THE VOLTAGE ON THE RICH SIDE. • IF THE CATALYTIC CONVERTER PURIFICATION CHARACTERISTIC DETERIORATES, THE AMOUNT OF THE TIME UNTIL THE HO2S DETECTS THE VOLTAGE ON THE RICH SIDE IS SHORTER COMPARED TO THE NORMAL PURIFICATION CHARACTERISTIC AS SHOWN. THE PCM DETECTS A CATALYTIC CONVERTER MALFUNCTION USING THIS CHARACTERISTIC. |
| 01-018-15-3070 | 2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P2610 AND P2507 STORED IN MEMORY AFTER ENGINE START AND ROOM FUSE 15A (A) REMOVED. • P2610:00: INSTRUMENT CLUSTER INTERNAL ENGINE OFF TIMER PERFORMANCE PROBLEM • P2507:00: PCM BATTERY VOLTAGE LOW INPUT AS A PAST MALFUNCTION, THE CUSTOMER WILL NOT NOTICE IT (NO WARNING LIGHT ILLUMINATED), BUT THE DTC MAY BE FOUND DURING A VEHICLE SERVICE. P2507 IN THIS SITUATION IS ONLY APPLICABLE ON 2016 AND LATER MODELS. THIS IS CAUSED BY THE ENGINE BEING STARTED 3 OR MORE TIMES AFTER A SHORT DURATION OF ENGINE OFF (LESS THAN 15 SECONDS) WITH THE ROOM FUSED REMOVED. |
| 09-030-15-3073 | 2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. MAZDA INFOTAINMENT SYSTEMS REQUIRE CONTACTING THE PROPER SOURCE FOR DIAGNOSTIC SUPPORT, PARTS AUTHORIZATION, AND PARTS EXCHANGE. SOME COMPONENTS REQUIRE PRIOR AUTHORIZATION BEFORE ORDERING AS EXCHANGE. REFER TO DAG EXCHANGE CENTRAL (MXCONNECT>PARTS AND ACCESSORIES>PARTS>PROGRAMS>EXCHANGE CENTRAL) FOR COMPONENT AVAILABILITY, SOURCE OF TECHNICAL SUPPORT AND PRIOR AUTHORIZATION REQUIREMENT. NOTE: ALWAYS CHECK FOR A TSB THAT MAY MODIFY OR ELIMINATE PRIOR AUTHORIZATION FOR A SPECIFIC SYMPTOM FOR A GIVEN COMPONENT. |
| 09-031-15-3076 | 2017-06-07. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). THE NAVIGATION SYSTEM SUPPORT FOR DIAGNOSTICS, PARTS AUTHORIZATION, AND PARTS EXCHANGE REQUIRE CONTACTING THE PROPER SOURCE. • TOMTOM NAVIGATION HELP DESK AT 866-486-6866 FROM 7AM-11PM (M-F) AND 9AM-8PM (SAT) EASTERN STANDARD TIME. NOTE: ONE OF THE FIRST STEPS FOR TROUBLESHOOTING THE NAVIGATION SYSTEM IS FOR THE CUSTOMER OR DEALER TO CALL TOMTOM. IF THE TOMTOM CALL CENTER CANNOT SOLVE THE CUSTOMER’S PROBLEM, THEY WILL PROVIDE A CASE NUMBER TO THE CUSTOMER THAT CAN BE REFERRED TO IF NEEDED. SERVICE ADVISORS SHOULD GET THIS CASE NUMBER FROM THE CUSTOMER IF THE VEHICLE COMES INTO THE DEALER FOR FURTHER DIAGNOSIS SO THE TECHNICIAN CAN HAVE IT WHEN CALLING TOMTOM. |
| 06-001-15-3054A | 2017-06-07. Service bulletin. STEERING. SOME VEHICLES MAY EXHIBIT AN UNUSUAL THUMPING NOISE FROM UNDER THE FRONT OF THE VEHICLE. THIS NOISE ONLY OCCURS WHEN STARTING TO MOVE THE VEHICLE WHILE THE STEERING WHEEL IS TURNED TO THE FULL LEFT POSITION. NOTE: THE NOISE WILL NOT OCCUR IF THE STEERING WHEEL IS IN THE CENTER OR FULL RIGHT POSITION. THE NOISE IS CAUSED WHEN THE EDGE OF THE LEFT SIDE INNER BALL JOINT GETS STUCK WITH THE STEERING GEAR HOUSING. TO ELIMINATE THE NOISE, THE SHAPE OF THE INNER BALL JOINT EDGE HAS BEEN CHANGED. |
| 09-032-15-3061 | 2017-06-07. Service bulletin. VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR; STRUCTURE:BODY:DOOR. SOME VEHICLES MAY EXHIBIT A VIBRATION FROM THE DRIVER-SIDE POWER DOOR MIRROR GLASS WHEN THE VEHICLE IS DRIVEN AT HIGH SPEEDS. THIS CONCERN MAY BE DUE TO A LACK OF RIGIDITY OF THE MIRROR BASE SO THE MIRROR VIBRATES WHEN IT RECEIVES VEHICLE VIBRATION OR WIND PRESSURE. AN ADDITIONAL REINFORCEMENT HAS BEEN INSTALLED INSIDE THE DOOR TO INCREASE THE DOOR PANEL STRENGTH WHERE THE DOOR MIRROR IS MOUNTED. ALSO, THE DOOR MIRROR SHAPE HAS BEEN CHANGED. BOTH OF THESE MODIFICATIONS HAVE BEEN IMPLEMENTED TO ELIMINATE MIRROR GLASS VIBRATION CONCERNS. |
| 09-008-15-2991C | 2017-06-07. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN ONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. C. “IPOD ERROR” MESSAGE FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6. THESE CONCERNS MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: • THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME. |
| 09-015-15-3026 | 2017-06-07. Service bulletin. SEATS:MID/REAR ASSEMBLY. WHEN FOLDING THE REAR SEAT BACK FORWARD, THE HEAD RESTRAINT (B) MAY CATCH ON THE FRONT SEAT BACK POCKET (A). IF WEIGHT IS APPLIED TO THE REAR SEAT AT THIS TIME (I.E. PASSENGER PUSHES ON REAR SEAT, ETC.), THE FRONT SEAT BACK POCKET MAY BECOME TORN. |
| 01-008-15-3045 | 2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXHIBIT THE CHECK ENGINE LIGHT ON WITH DTC P0456 STORED IN THE PCM MEMORY. • P0456: EVAP SYSTEM LEAK DETECTED (VERY SMALL LEAK) THE CONCERN IS MOST LIKELY THE RESULT OF THE CUSTOMER NOT GETTING THE FUEL CAP COMPLETELY CLOSED AFTER FUELING THE VEHICLE. THIS CAUSES A SMALL FUEL VAPOR LEAK AND TURNS DTC P0456 ON. |
| 09-016-15-3041 | 2017-06-07. Service bulletin. STRUCTURE:BODY:DOOR. SOME VEHICLES MAY EXPERIENCE A RATTLE NOISE FROM THE FRONT DOOR GLASS WHEN DRIVING WITH THE WINDOW OPEN APPROX. 1/2 TO 4 INCHES (1 - 10 CM). THE RATTLE NOISE MAY BE CAUSED BY INSUFFICIENT HOLDING FORCE OF THE GLASS RUN CHANNEL. TO INCREASE THE HOLDING FORCE, THE SHAPE OF GLASS RUN CHANNEL HAS BEEN CHANGED AND NON-WOVEN PADS HAVE BEEN ATTACHED TO THE GLASS RUN CHANNEL. |
| 02-005-15-3044 | 2017-06-07. Service bulletin. SUSPENSION:REAR:SHOCK ABSORBER. SOME VEHICLES MAY EXHIBIT A CHIRP/CLUNK TYPE NOISE FROM THE REAR SHOCK ABSORBERS (A) WHEN DRIVING ON A ROUGH ROAD OR PASSING OVER A SPEED BUMP. VISUAL INSPECTION OF THE SHOCK ABSORBERS SHOW NO EXTERNAL DAMAGE. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.