WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Mazda CX-5

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

789 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
06-001-15-30542017-05-17. Service bulletin. STEERING: STEERING WHEEL/HANDLE BAR. SOME VEHICLES MAY EXHIBIT AN UNUSUAL THUMPING NOISE FROM UNDER THE FRONT OF THE VEHICLE. THIS NOISE ONLY OCCURS WHEN STARTING TO MOVE THE VEHICLE WHILE THE STEERING WHEEL IS TURNED TO THE FULL LEFT POSITION. NOTE: THE NOISE WILL NOT OCCUR IF THE STEERING WHEEL IS IN THE CENTER OR FULL RIGHT POSITION. THE NOISE IS CAUSED WHEN THE EDGE OF THE LEFT SIDE INNER BALL JOINT GETS STUCK WITH THE STEERING GEAR HOUSING. TO ELIMINATE THE NOISE, THE SHAPE OF THE INNER BALL JOINT EDGE HAS BEEN CHANGED.
01-015-15-30642017-05-17. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES USING AN AUXILIARY HEATER (BLOCK HEATER) MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0116:00 OR P011A WHEN STARTING IN COLD WEATHER BELOW 32 °F (0 °C). • P0116:00: ECT SENSOR NO.1 CIRCUIT RANGE/PERFORMANCE PROBLEM • P011A:00: ECT SENSOR NO.1/NO.2 PERFORMANCE PROBLEM. THIS IS CAUSED BY ERROR DETECTION LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.
09-006-15-2904A2017-05-17. Service bulletin. SEATS:FRONT ASSEMBLY:POWER ADJUST. SOME VEHICLES (WITHOUT POWER SEATS) MAY EXHIBIT A DRIVER SEAT THAT GRADUALLY MOVES DOWN BY ITSELF. THIS CONCERN MAY BE CAUSED WHEN A LOAD, WHICH IS APPLIED TO THE SEAT DURING BRAKING, EXCEEDS A CERTAIN LEVEL THAT COULD IMPACT THE RETAINING MECHANISM OF THE SEAT LIFTER CAUSING THE SEAT TO GRADUALLY MOVE DOWNWARD. TO ELIMINATE THIS CONCERN, THE PLAY IN THE LIFT MECHANISM GEARS HAS BEEN REDUCED.
01-011-15-3051A2017-05-16. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE A LACK OF POWER DURING HARD ACCELERATION (APPROX. 6,000 RPM) IN COLD WEATHER CONDITIONS BELOW 32 °F (0 °C). DTCS P0300:00, P0301:00 AND/OR P0302:00 ARE STORED IN MEMORY. • P0300:00: RANDOM MISFIRE DETECTED • P0301:00: CYLINDER NO. 1 MISFIRE DETECTED • P0302:00: CYLINDER NO. 2 MISFIRE DETECTED THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. THE PCM MAY DETECT A FALSE MISFIRE UNDER THE SUBJECT CONDITIONS AND MAY FALL INTO FAIL SAFE MODE. TO ELIMINATE THIS CONCERN, THE PCM CONTROL LOGIC HAS BEEN CHANGED.
01-005-15-3030A2017-05-16. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0300:00, P0301:00, P0302:00, P0303:00 AND/OR P0304:00 STORED IN MEMORY AND ACCOMPANIED WITH AN INCREASED ENGINE OIL LEVEL. P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO.1 MISFIRE DETECTED P0302:00: CYLINDER NO.2 MISFIRE DETECTED P0303:00: CYLINDER NO.3 MISFIRE DETECTED P0304:00: CYLINDER NO.4 MISFIRE DETECTED THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. IN COLD WEATHER BELOW 14 °F (-10 °C) WITH REPEATED SHORT TIME OPERATION, EXCESS FUEL INJECTED IN THE CYLINDERS MAY ACCUMULATE IN THE CRANK CASE AND RESULT IN INCREASED OIL LEVEL AND MISFIRE.
09-025-15-30572017-05-16. Service bulletin. EQUIPMENT:ELECTRICAL. SOME VEHICLES MAY EXHIBIT EITHER AN AUDIO SCREEN THAT IS LOCKING-UP (BLACK SCREEN) OR AN INOPERATIVE AUDIO TOUCH SCREEN. IN BOTH CASES HOWEVER, THE AUDIO UNIT SOUND OUTPUT IS NORMAL. THIS CONCERN MAY BE CAUSED BY AN INTERNAL FAILURE OF THE AUDIO UNIT. THE PRODUCTION PROCESS AT THE AUDIO SUPPLIER HAS BEEN IMPROVED TO ELIMINATE THESE CONCERNS.
02-004-14-29762017-05-11. Service bulletin. STEERING: STEERING WHEEL/HANDLE BAR. SOME CUSTOMERS MAY COMPLAIN THAT THE STEERING WHEEL IS OFF CENTER MORE THAN 3° EVEN WHEN DRIVING STRAIGHT ON A FLAT ROAD. FOLLOW STEERING WHEEL ALIGNMENT PROCEDURE.
09-048-14-29752017-05-11. Service bulletin. FUEL SYSTEM, OTHER:STORAGE:FUEL GAUGE SYSTEM. SOME CUSTOMERS MAY COMPLAIN THAT THE FUEL GAUGE SHOWS EMPTY AND/OR THE DISTANCE-TO-EMPTY ON THE MULTI-INFORMATION DISPLAY (MID) INDICATES “0” WITH A CERTAIN AMOUNT OF FUEL REMAINING IN THE TANK.THIS MAY BE A NORMAL OPERATION OF THE FAIL-SAFE FUNCTION:1.IF FOREIGN MATERIAL (CONTAINED IN A POOR-QUALITY FUEL) ADHERES TO THE FUEL GAUGE SENDER UNIT, THE FAIL-SAFE FUNC-TION INITIATES BY FORCING THE FUEL GAUGE AND THE DISTANCE-TO-EMPTY TO INDICATE “ZERO FUEL AMOUNT”.2.IMMEDIATELY AFTER THE FOREIGN MATERIAL IS DISLODGED BY SHAKING OF THE FUEL DURING DRIVING OR REFUELING, THE FUEL GAUGE WILL RETURN TO A NORMAL READING, BUT THE DISTANCE-TO-EMPTY WILL CONTINUE TO READ “0” UNTIL THE NEXT REFUEL-ING OF 3 US GALLONS (10 LITERS) OR MORE.TO CORRECT THE PROBLEM THE FOLLOWING CHANGE HAS BEEN MADE:1.THERE IS NO MASS-PRODUCTION CHANGE TO PREVENT ADHESION OF FOREIGN MATERIAL TO THE FUEL GAUGE SENDER UNIT. SO THE FACT REMAINS UNCHANGED THAT THE FUEL GAUGE AND THE DISTANCE-TO-EMPTY INDICATE “ZERO FUEL AMOUNT” WHEN FOREIGN MATERIAL ADHERES TO THE FUEL GAUGE SENDER UNIT, AND THE FAIL-SAFE FUNCTION INITIATES.2.TO EQUALIZE THE RECOVERY TIMING FROM THE FAIL-SAFE MODE, THE LOGIC HAS BEEN CHANGED SO THAT THE DISTANCE-TO-EMPTY RECOVERS FROM “0” TO A NORMAL READING IMMEDIATELY AFTER THE FOREIGN MATERIAL IS DISLODGED (AT THE SAME TIME AS THE FUEL GAUGE).
09-048-14-2975A2017-05-11. Service bulletin. FUEL SYSTEM, OTHER:STORAGE:FUEL GAUGE SYSTEM. SOME CUSTOMERS MAY COMPLAIN THAT THE FUEL GAUGE SHOWS EMPTY AND/OR THE DISTANCE-TO-EMPTY ON THE MULTI-INFORMATION DISPLAY (MID) INDICATES “0” WITH A CERTAIN AMOUNT OF FUEL REMAINING IN THE TANK.THIS MAY BE A NORMAL OPERATION OF THE FAIL-SAFE FUNCTION:1.IF FOREIGN MATERIAL (CONTAINED IN A POOR-QUALITY FUEL) ADHERES TO THE FUEL GAUGE SENDER UNIT, THE FAIL-SAFE FUNC-TION INITIATES BY FORCING THE FUEL GAUGE AND THE DISTANCE-TO-EMPTY TO INDICATE “ZERO FUEL AMOUNT”.2.IMMEDIATELY AFTER THE FOREIGN MATERIAL IS DISLODGED BY SHAKING OF THE FUEL DURING DRIVING OR REFUELING, THE FUEL GAUGE WILL RETURN TO A NORMAL READING, BUT THE DISTANCE-TO-EMPTY WILL CONTINUE TO READ “0” UNTIL THE NEXT REFUEL-ING OF 3 US GALLONS (10 LITERS) OR MORE.TO CORRECT THE PROBLEM THE FOLLOWING CHANGE HAS BEEN MADE:1.THERE IS NO MASS-PRODUCTION CHANGE TO PREVENT ADHESION OF FOREIGN MATERIAL TO THE FUEL GAUGE SENDER UNIT. SO THE FACT REMAINS UNCHANGED THAT THE FUEL GAUGE AND THE DISTANCE-TO-EMPTY INDICATE “ZERO FUEL AMOUNT” WHEN FOREIGN MATERIAL ADHERES TO THE FUEL GAUGE SENDER UNIT, AND THE FAIL-SAFE FUNCTION INITIATES.2.TO EQUALIZE THE RECOVERY TIMING FROM THE FAIL-SAFE MODE, THE LOGIC HAS BEEN CHANGED SO THAT THE DISTANCE-TO-EMPTY RECOVERS FROM “0” TO A NORMAL READING IMMEDIATELY AFTER THE FOREIGN MATERIAL IS DISLODGED (AT THE SAME TIME AS THE FUEL GAUGE).
09-020-14-2913C2017-05-11. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.854 OR LATER).•NAVIGATION SYSTEM FREEZES.•MESSAGE “WAITING FOR VALID GPS SIGNAL” IS SHOWN IN THE MENU BAR OF NAVIGATION DISPLAY FOR SEVERAL MINUTES.•VEHICLE SYMBOL IS OFF ROAD WHILE DRIVING / WRONG POSITION OF VEHICLE ON MAP.•MAP IS ROTATING WHEN VEHICLE IS PARKED OR WHILE DRIVING.•NAVIGATION SCREEN DON’T APPEAR AFTER DEPRESSING NAVIGATION BUTTON. THEN IT DOES NOT RECOVER BY OPERATING ACC OFF TO ON POSITION.•UNEXPECTED “STOPPING VOICE CONTROL” MESSAGE, USUALLY WHEN STARTING THE VEHICLE.•CURRENT CAR POSITION (CCP) TURNING 180 DEGREES WHEN DRIVING IN REVERSE.•THE MESSAGE “WAITING FOR A VALID GPS SIGNAL” APPEARS.•RED SCREEN WITH MESSAGE "PROBLEM WITH MAP".•YELLOW SCREEN WITH MESSAGE "INSERT SD CARD".•NO MAP FOUND ERROR AND SD CARD CONTAINS A MAP.•SCREEN TEMPORARILY GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) FOR 2 MINUTES DURING STARTUP. AFTERWARDS, THE NAVIGATION WILL NOT START UNTIL THE IGNITION IS CYCLED.•SCREEN GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) DURING STARTUP.•SCREEN LOCKS UP TO A "BLACK SCREEN”.•VEHICLE ICON JUMPS AROUND OR VIBRATES.•IF NAVIGATION BUTTON IS PRESSED DURING AUDIO SCREEN, THE SCREEN FREEZES AND THE TOUCH SCREEN BECOMES INOPERATIVE.
09-049-14-29802017-05-11. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS. WHEN DEALING WITH CUSTOMER COMPLAINTS OF EXCESSIVE CONDENSATION AND/OR WATER WITHIN THE HEADLAMP UNIT, FIRST DETERMINE IF ALL THE BULB SOCKETS ARE PRESENT AND CORRECTLY INSTALLED. IN MOST CASES YOU WILL FIND THAT THE BULB SEAL NO. 1 (A) OR HID BULB SEAL NO. 1 (B) AND BULB SEAL NO. 2 (C) SOCKET COVERS HAVE NOT BEEN CORRECTLY INSTALLED OR ARE MISSING DUE TO IMPROPER PRIOR REPAIRS (I.E., CUSTOMER REPLACING THE HEADLAMP BULBS OR BODY SHOP NOT TRANSFERRING THEM WHEN REPLACING THE HEADLAMP UNIT(S) DUE TO A COLLISION). ANY DAMAGE CAUSED BY MISSING SOCKET COVERS, HID MODULE SEAL (D), OR MISSING BUMPER BRACKETS (E) IS NOT COVERED BY WARRANTY POLICY.
05-008-14-2920A2017-05-11. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY. SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS: • HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR. • SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) THIS IS CAUSED BY A FAILURE OF THE RELATED CLUTCH HUB(S). TO CORRECT THE PROBLEM OF HARD SHIFTING, THE SHAPE OF THE 3-4 AND 5-6 CLUTCH HUB HAS BEEN CHANGED. A SURFACE TREATMENT HAS NOW BEEN ADDED TO THE 3-4 CLUTCH HUB TO PREVENT 3RD GEAR FROM JUMPING OUT.
09-002-14-2864A2017-05-11. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. WHILE DRIVING OVER ROUGH OR BUMPY ROADS, SOME VEHICLES MAY EXHIBIT A RATTLE NOISE FROM THE INSTRUMENT PANEL AND/OR A CREAK NOISE FROM THE A-PILLAR.RATTLE NOISE FROM INSTRUMENT PANEL:THE RATTLE NOISE MAY BE CAUSED BY LOW COWL PANEL (A) MOUNTING BOLT (B) TORQUE. CREAK NOISE FROM A-PILLAR:THIS NOISE MAY BE CAUSED BY TWO JOINED PANELS (A) SCRAPING TOGETHER AT THE A-PILLAR. THE PANEL WELD AREAS HAVE BEEN IMPROVED DURING THE MASS-PRODUCTION OF VEHICLES WITH VINS JM3KE******128359 (PRODUCED JUNE 1, 2012) OR HIGHER.
00-003-14-29702017-05-11. Service bulletin. EQUIPMENT. IN SUPPORT OF SKYACTIV MANUAL TRANSMISSION MODELS, MAZDA WILL SHIP TO ALL DEALERS ONE (1) NEW SPECIAL SER-VICE TOOL (SST). THE SST WILL BE SHIPPED AUTOMATICALLY BY MAZDA’S TOOL VENDOR SNAP-ON TOOLS, STARTING IN MID-OCTOBER 2014.THE FOLLOWING SST IS THE LATEST ADDITION TO THE MAZDA REQUIRED TOOL (MRT) LIST.
09-044-14-29712017-05-11. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. SOME VEHICLES MAY EXHIBIT LOW OR NO SOUND FROM SOME (OR ALL) OF THE BOSE AUDIO SYSTEM SPEAKERS (I.E. LEFT AND RIGHT FRONT DOOR SPEAKERS, FRONT CENTER SPEAKER AND LEFT AND RIGHT D-PILLAR SPEAKERS).THE POWER AMPLIFIER, WHICH CONTROLS THE OUTPUT TO THE SPEAKERS MAY BE INOPERATIVE DUE TO THE OCCURRENCE OF PAR-ASITIC RESISTANCE IN THE CIRCUIT.
01-017-14-29732017-05-11. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE MIL ILLUMINATION WITH DTC P2610 (INSTRUMENT CLUSTER INTERNAL ENGINE OFF TIMER PERFORMANCE PROBLEM) STORED IN MEMORY AFTER ENGINE START AND ROOM FUSE 15A (A) REMOVED. NOTE:THE ODOMETER WILL DISPLAY “F0-002” DURING TRANSPORT MODE (ROOM FUSE 15A REMOVED). TRANSPORT MODE IS CANCELED WHEN ROOM FUSE 15A IS INSTALLED OR THE VEHICLE ODOMETER IS MORE THAN 12.4MI (20KM).
02-003-14-2954A2017-05-11. Service bulletin. SUSPENSION:REAR:SHOCK ABSORBER. SOME VEHICLES MAY EXHIBIT A CHIRP NOISE FROM THE REAR SHOCK ABSORBERS (A) WHEN DRIVING ON A ROUGH ROAD OR PASSING OVER A SPEED BUMP. VISUAL INSPECTION OF THE SHOCK ABSORBERS SHOW NO EXTERNAL DAMAGE OR OIL LEAKAGE.
07-002-14-29642017-05-11. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. SOME CUSTOMERS MAY COMPLAIN ABOUT NO COOL AIR FROM THE VENTS WHEN THE AIR CONDITIONER (A/C) IS ON. THIS CON-CERN MAY BE CAUSED BY A/C REFRIGERANT LEAKING FROM THE EVAPORATOR. SOME DEFORMED EVAPORATOR TUBES SLIPPED THROUGH QUALITY INSPECTION AND WERE USED DURING PRODUCTION. A/C REFRIGERANT LEAKS FROM IMPROPER BRAZING AT A JOINT. TO CORRECT THE PROBLEM, THE PRODUCTION AND INSPECTION CONTROL OF THE EVAPORATOR HAVE BEEN IMPROVED.
09-020-14-2913B2017-05-11. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ELECTRICAL SYSTEM:SOFTWARE. SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.854 OR LATER).•NAVIGATION SYSTEM FREEZES.•MESSAGE “WAITING FOR VALID GPS SIGNAL” IS SHOWN IN THE MENU BAR OF NAVIGATION DISPLAY FOR SEVERAL MINUTES.•VEHICLE SYMBOL IS OFF ROAD WHILE DRIVING / WRONG POSITION OF VEHICLE ON MAP.•MAP IS ROTATING WHEN VEHICLE IS PARKED OR WHILE DRIVING.•NAVIGATION SCREEN DON’T APPEAR AFTER DEPRESSING NAVIGATION BUTTON. THEN IT DOES NOT RECOVER BY OPERATING ACC OFF TO ON POSITION.•UNEXPECTED “STOPPING VOICE CONTROL” MESSAGE, USUALLY WHEN STARTING THE VEHICLE.•CURRENT CAR POSITION (CCP) TURNING 180 DEGREES WHEN DRIVING IN REVERSE.•THE MESSAGE “WAITING FOR A VALID GPS SIGNAL” APPEARS.•RED SCREEN WITH MESSAGE "PROBLEM WITH MAP".•YELLOW SCREEN WITH MESSAGE "INSERT SD CARD".•NO MAP FOUND ERROR AND SD CARD CONTAINS A MAP.•SCREEN TEMPORARILY GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) FOR 2 MINUTES DURING STARTUP. AFTERWARDS, THE NAVIGATION WILL NOT START UNTIL THE IGNITION IS CYCLED.•SCREEN GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) DURING STARTUP.•SCREEN LOCKS UP TO A "BLACK SCREEN”.•VEHICLE ICON JUMPS AROUND OR VIBRATES.
01-009-14-2909A2017-05-08. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY.•P0015:00 - EXHAUST CMP TIMING OVER-RETARDED•P0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
09-025-14-2925A2017-05-08. Service bulletin. EQUIPMENT. SOME VEHICLES MAY EXHIBIT A CRACKING NOISE ORIGINATED AT THE POSITIONING PINS NEAR THE TOP CORNERS OF THE WIND-SHIELD AND/OR REAR WINDOW WHEN DRIVING ON UNEVEN ROAD SURFACE. THIS HAPPENS WHEN THE AMBIENT TEMPERATURE IS APPROXIMATELY 14 °F (-10 °C) OR LOWER AND THE VEHICLE CABIN HAS NOT YET WARMED UP. THE NOISE IS CAUSED BY THE WINDSHIELD AND/OR REAR WINDOW LOCATING STOPPER CONTACTING THE PANEL.
09-039-14-29232017-05-08. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; EQUIPMENT:ELECTRICAL. SOME VEHICLES MAY EXHIBIT BLUETOOTH® HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. TO IMPROVE THE HANDLING OF BLUETOOTH® HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CRE-ATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM AS OF FEBRUARY 2010.
02-003-14-29542017-05-08. Service bulletin. SUSPENSION:REAR:SHOCK ABSORBER. SOME VEHICLES MAY EXHIBIT A CHIRP NOISE FROM THE REAR SHOCK ABSORBERS (A) WHEN DRIVING ON A ROUGH ROAD OR PASSING OVER A SPEED BUMP. VISUAL INSPECTION OF THE SHOCK ABSORBERS SHOW NO EXTERNAL DAMAGE OR OIL LEAKAGE.
09-034-14-29562017-05-05. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. IN ACCORDANCE WITH FEDERAL REGULATIONS, FOLLOW THE PROCEDURE LISTED BELOW WHEN REPLACING A SPEEDOMETER.NOTE:•MAZDA VEHICLES ARE MANUFACTURED WITH TAMPER-PROOF SPEEDOMETERS.•WHEN A SPEEDOMETER IS REPLACED, THE NEW SPEEDOMETER WILL READ ZERO (0) MILES.•THIS PROCEDURE IS EXTREMELY IMPORTANT TO ACCURATELY REPRESENT ACTUAL VEHICLE MILEAGE.•PRIOR TO SPEEDOMETER REMOVAL, COMPLETE THE INFORMATION REQUIRED ON THE “SPEEDOMETER REPLACE-MENT LABEL”. •LABELS CAN ONLY BE ORDERED THROUGH MSTORE, NOT MDCS.
09-033-14-2944A2017-05-05. Service bulletin. SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER. SOME VEHICLES MAY EXHIBIT AN INOPERATIVE SEAT WARMER (OR SEAT HEATER) ON THE DRIVER AND/OR PASSENGER SEAT. WHEN WEIGHT IS APPLIED TO THE SEAT, PART OF THE HEATER ELEMENT WIRE MAY COME OUT OF POSITION AND BECOME BENT. UNDER REPEATED STRESS, THE WIRE MAY BREAK CAUSING AN INOPERATIVE SEAT WARMER CONDITION.AN ADDITIONAL ADHESION TREATMENT HAS BEEN APPLIED TO ELIMINATE THE HEATER ELEMENT WIRE FROM COMING OUT OF THE POSITION.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.