Service bulletins for the 2014 Mazda CX-5
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
789 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Labels and manuals are shown. Show all
| 01-009-14-2909 | 2017-05-04. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. • P0015:00 - EXHAUST CMP TIMING OVER-RETARDED • P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME. |
|---|---|
| 01-010-14-2896 | 2017-05-04. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE MIL ON WITH DTC P0191:00 (FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFOR-MANCE PROBLEM) STORED IN MEMORY. THIS IS CAUSED BY THE HIGH PRESSURE FUEL PUMP NOT GENERATING THE TARGET FUEL PRESSURE (DUE TO A MANUFACTURING ERROR OF THE INNER PARTS). TO CORRECT THE PROBLEM, PRODUCTION CONTROL HAS BEEN IMPROVED. |
| 01-010-14-2896A | 2017-05-04. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE MIL ON WITH DTC P0191:00 (FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFOR-MANCE PROBLEM) STORED IN MEMORY. THIS IS CAUSED BY THE HIGH PRESSURE FUEL PUMP NOT GENERATING THE TARGET FUEL PRESSURE (DUE TO A MANUFACTURING ERROR OF THE INNER PARTS). TO CORRECT THE PROBLEM, PRODUCTION CONTROL HAS BEEN IMPROVED. |
| 05-005-14-2902B | 2017-05-04. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY.•P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON•P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON•P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON•P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONTHE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER.•P0780:00 - GEAR SHIFTING MALFUNCTION•P1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTIONTHIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. |
| 05-005-14-2902C | 2017-05-04. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY.•P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON•P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON•P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON•P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONTHE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER.•P0780:00 - GEAR SHIFTING MALFUNCTION•P1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTIONTHIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. |
| 01-010-14-2896B | 2017-05-03. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0191:00 OR DTC P0192:00 STORED IN MEMORY. DTC P0191:00: FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFORMANCE PROBLEM (EXCEPT 2014 MAZDA3) DTC P0192:00: FUEL PRESSURE SENSOR CIRCUIT LOW INPUT (2014 MAZDA3) THIS IS CAUSED BY THE HIGH PRESSURE FUEL PUMP NOT GENERATING THE TARGET FUEL PRESSURE (DUE TO A MANUFACTURING ERROR OF THE INNER PARTS). TO CORRECT THE PROBLEM, PRODUCTION CONTROL HAS BEEN IMPROVED. |
| 05-005-14-2902D | 2017-05-03. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY.•P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON•P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON•P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON•P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONTHE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER.•P0780:00 - GEAR SHIFTING MALFUNCTION•P1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION. NOTE: THIS SERVICE INFORMATION IS ALSO APPLICABLE IF DTC P0780:00 IS STOREED INDEPENDENTLY. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. |
| 09-020-14-2913A | 2017-05-03. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.852 OR LATER).• VEHICLE ICON JUMPS AROUND OR VIBRATES. CAUTION: DO NOT USE THE FACTORY RESET FOR RETAIL VEHICLES. OTHERWISE, PERSONAL SETTINGS (SUCH AS DISPLAY AND SOUND ADJUSTMENTS) WILL BE LOST, INCLUDING FAVORITES INFORMATION. |
| 09-005-14-2875C | 2017-05-03. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE ONE OR MORE OF THE FOLLOWING SYMPTOMS IN CONNECTION WITH A MALFUNCTION RELATED TO THE C-15 CONNECTOR. •THE DRIVER SIDE POWER WINDOW DOES NOT OPERATE.•THE DOOR DOES NOT OPEN WHEN USING THE ADVANCED KEYLESS SYSTEM.•THE WARNING LAMP STAYS ON EVEN AFTER THE IGNITION SWITCH IS TURNED OFF.•DTC B10E7:17 (START STOP UNIT, IG1 RELAY CIRCUIT MALFUNCTION) AND DTCS RELATED TO COMMUNICATION ERRORS MAY BE STORED IN PCM MEMORY.THE SYMPTOMS LISTED ABOVE MAY BE CAUSED BY CORROSION OF THE C-15 CONNECTOR TERMINALS DUE TO WATER INTRUSION THROUGH THE FRONT DOOR. IN LOW AMBIENT TEMPERATURES, THE DOOR HARNESS HARDENS. IF THE DOOR IS FULLY OPENED, IT MAY CREATE A GAP BETWEEN THE DOOR AND THE DOOR HARNESS GROMMET, WHICH MAY ALLOW WATER TO ENTER THROUGH THE GAP. |
| 09-005-14-2875B | 2017-04-27. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE ONE OR MORE OF THE FOLLOWING SYMPTOMS IN CONNECTION WITH A MALFUNCTION RELATED TO THE C-15 CONNECTOR. • THE DRIVER SIDE POWER WINDOW DOES NOT OPERATE. • THE DOOR DOES NOT OPEN WHEN USING THE ADVANCED KEYLESS SYSTEM. • THE WARNING LAMP STAYS ON EVEN AFTER THE IGNITION SWITCH IS TURNED OFF.THE SYMPTOMS LISTED ABOVE MAY BE CAUSED BY CORROSION OF THE C-15 CONNECTOR TERMINALS DUE TO WATER INTRUSION THROUGH THE FRONT DOOR. IN LOW AMBIENT TEMPERATURES, THE DOOR HARNESS HARDENS. IF THE DOOR IS FULLY OPENED, IT MAY CREATE A GAP BETWEEN THE DOOR AND THE DOOR HARNESS GROMMET, WHICH MAY ALLOW WATER TO ENTER THROUGH THE GAP. |
| 05-005-14-2902 | 2017-04-27. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY. • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON THE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER. • P0780:00 - GEAR SHIFTING MALFUNCTION • P1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. |
| 05-005-14-2902A | 2017-04-27. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY. • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON THE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER. • P0780:00 - GEAR SHIFTING MALFUNCTION • P1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. |
| 09-005-14-2875A | 2017-04-27. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE ONE OR MORE OF THE FOLLOWING SYMPTOMS IN CONNECTION WITH A MALFUNCTION RELATED TO THE C-15 CONNECTOR. • THE DRIVER SIDE POWER WINDOW DOES NOT OPERATE. • THE DOOR DOES NOT OPEN WHEN USING THE ADVANCED KEYLESS SYSTEM. • THE WARNING LAMP STAYS ON EVEN AFTER THE IGNITION SWITCH IS TURNED OFF.THE SYMPTOMS LISTED ABOVE MAY BE CAUSED BY CORROSION OF THE C-15 CONNECTOR TERMINALS DUE TO WATER INTRUSION THROUGH THE FRONT DOOR. IN LOW AMBIENT TEMPERATURES, THE DOOR HARNESS HARDENS. IF THE DOOR IS FULLY OPENED, IT MAY CREATE A GAP BETWEEN THE DOOR AND THE DOOR HARNESS GROMMET, WHICH MAY ALLOW WATER TO ENTER THROUGH THE GAP. MASS PRODUCTION CHANGES: • THE FRONT DOOR HARNESS GROMMET HAS BEEN CHANGED TO IMPROVE SEALING PERFORMANCE. • HOLES INSIDE THE FRONT PILLAR (WHICH ARE MADE FOR WEIGHT REDUCTION), HAVE BEEN COVERED TO PREVENT WATER INTRUSION. |
| 05-002-14-2894 | 2017-04-27. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXHIBIT THE ATX FAIL-SAFE FUNCTION WORKING WITH THE FOLLOWING SYMPTOMS: • THE VEHICLE SPEED DOES NOT INCREASE WITH ENGINE SPEED • THE ATX DOES NOT SHIFT UP OR DOWN AS EXPECTED. THE CONDITION MAY NOT ALWAYS BE ABLE TO BE REPRODUCED AND DTCS MAY NOT BE STORED WHEN THE VEHICLE IS BROUGHT IN. FOREIGN MATERIAL (IRON PARTICLES IN THE ATF) MAY ENTER THE ATX VALVE BODY AND CAUSE A TEMPORARY MALFUNCTION OF THE VALVE BODY AND/OR SENSOR (ATX FAIL-SAFE FUNCTION ACTIVATED). THE FAIL-SAFE FUNCTION IS CANCELED WITHOUT DTCS RECORDED IF THE MALFUNCTION GOES AWAY AND DOES NOT OCCUR AGAIN AT THE NEXT DRIVE CYCLE. FAIL-SAFE FUNCTION OPERATION: • IF A TECHNICAL FAULT IS DETECTED IN THE ATX BY THE MALFUNCTION DETECTION FUNCTION, THE FAIL-SAFE FUNCTION LIMITS THE ATX CONTROL (INHIBITS SOME GEARS OR SHIFT DOWN FUNCTIONS). • EVEN IN CASE OF AN ATX MALFUNCTION, THE FAIL-SAFE FUNCTION ALLOWS MINIMUM VEHICLE DRIVEABILITY. |
| 00-001-12-2743 | 2017-04-26. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. IN SUPPORT OF THE NEW 2014 MAZDA6 AND THE 2014 CX-5, MAZDA WILL SHIP TO ALL DEALERS ONE (1) NEW SPECIAL SERVICE TOOL (SST). THE SST WILL BE SHIPPED AUTOMATICALLY BY MAZDA’S TOOL VENDOR, SPX DURING JANUARY 2013. THE FOLLOWING SST IS THE LATEST ADDITION TO THE MAZDA REQUIRED TOOL (MRT) LIST. |
| 00-004-12-2741 | 2017-04-26. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. MAZDA HAS DEVELOPED FACTORY RECOMMENDED SCHEDULED MAINTENANCE SERVICES THAT SUPPORT ALL MAJOR VEHICLE SYSTEMS. MAZDA RECOMMENDS DEALERS FOLLOW THE SCHEDULED MAINTENANCE TABLES AS CITED IN THE VEHICLE-SPECIFIC WORKSHOP MANUAL OR OWNER’S MANUAL. SERVICES PERFORMED OUTSIDE OF MAZDA’S FACTORY SCHEDULED MAINTENANCE ARE NOT RECOMMENDED. THESE SERVICES ARE UNNECESSARY AND CREATE UNNEEDED EXPENSES FOR YOUR CUSTOMERS. |
| 04-003-13-2823 | 2017-04-24. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE TCS/DSC INDICATOR LIGHT AND THE TPMS WARNING LIGHT BOTH ON WITH DTC C0051:62 STORED IN MEMORY.•DTC C0051:62 - THE DIFFERENCE BETWEEN THE INITIAL LEARNED VALUE OF THE STEERING ANGLE (AS CALCULATED BY EACH SENSOR) AND THE STEERING ANGLE (AS CALCULATED BY THE STEERING ANGLE SENSOR) WHILE DRIVING IN A STRAIGHT LINE, HAS EXCEEDED ITS ALLOWABLE TOLERANCE (OR THRESHOLD).NOTE:FOR VEHICLES EQUIPPED WITH THE SMART CITY BRAKE SYSTEM (SCBS), THE MASTER WARNING LIGHT ALSO COMES ON WITH THE MESSAGE "SCBS INSPECTION REQUIRED" IN THE DISPLAY.THE SYMPTOMS MAY OCCUR WHEN THE FOLLOWING CONDITIONS ARE MET: •AFTER STARTING THE ENGINE, THE VEHICLE IS DRIVEN BACKWARDS WHILE THE STEERING WHEEL IS TURNED TO THE LEFT OR TO THE RIGHT. THE VEHICLE IS THEN DRIVEN FORWARD AND BEGINS ACCELERATING WHILE THE STEERING WHEEL IS STILL TURNED.TO ELIMINATE THIS CONCERN, THE DSC HU/CM SOFTWARE HAS BEEN CHANGED. |
| 01-001-13-2746B | 2017-04-24. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE MIL ILLUMINATION WITH DTC P2610 (INSTRUMENT CLUSTER INTERNAL ENGINE OFF TIMER PERFORMANCE PROBLEM) STORED IN MEMORY AFTER ENGINE START AND ROOM FUSE 15A (A) REMOVED. NOTE:THE ODOMETER WILL DISPLAY “F0-002” DURING TRANSPORT MODE (ROOM FUSE 15A REMOVED). TRANSPORT MODE IS CANCELED WHEN ROOM FUSE 15A IS INSTALLED OR THE VEHICLE ODOMETER IS MORE THAN 12.4MI (20KM). |
| 02-003-13-2762B | 2017-04-21. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. THIS SERVICE BULLETIN ILLUSTRATES THE CONDITIONS WHEN A TPMS WARNING LIGHT MAY ILLUMINATE, WHY IT ILLUMINATED AND HOW TO PROPERLY INITIALIZE THE SYSTEM.THE TIRE PRESSURE MONITORING SYSTEM (TPMS) MONITORS THE TIRE PRESSURE OF ALL FOUR TIRES INDIRECTLY USING THE DATA SENT FROM THE ABS WHEEL SPEED SENSORS. IF THE AIR PRESSURE OF ONE OR MORE TIRES IS TOO LOW COMPARED WITH THE SPECIFIED VALUE (THE INITIAL VALUE LEARNED BY THE SYSTEM), THE SYSTEM WARNS THE DRIVER WITH THE TPMS WARNING LIGHT IN THE INSTRUMENT CLUSTER AND A BEEP SOUND. TO ALLOW THE TPMS TO OPERATE CORRECTLY, IT IS ESSENTIAL THAT THE TPMS BE INITIALIZED TO LEARN NEW CONDITIONS WHENEVER A TIRE RELATED SERVICE IS PERFORMED. |
| 09-018-13-2803 | 2017-04-14. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME CUSTOMERS MAY COMPLAIN THAT THE AMBIENT TEMPERATURE DISPLAY IS NOT ACCURATE, OR IT TAKES TOO LONG FOR THE DISPLAY TO SHOW ACTUAL TEMPERATURE. WHEN YOU ENCOUNTER A CUSTOMER WITH THIS CONCERN, FIRST VERIFY THE CONDITION WHEN THE CUSTOMER NOTICED THIS SYMPTOM. IF THE CONDITION IS SIMILAR TO THE FOLLOWING “CONTROL LOGIC OF AMBIENT TEMPERATURE” OR “DIFFERENCE BETWEEN THE TEMPERATURE DISPLAY AND OTHERS”, ADVISE THE CUSTOMER THAT THIS IS A NORMAL CHARACTERISTIC OF THE VEHICLE AND NOT A MALFUNCTION. IF THE CONDITION DOES NOT MEET THE FOLLOWING AND THE SENSOR MALFUNCTION IS SUSPECTED, MAKE SURE TO INSPECT THE SENSOR ACCORDING TO MS3 ONLINE OR WORKSHOP MANUAL (SECTION 09-22 AMBIENT TEMPERATURE SENSOR INSPECTION). |
| 09-019-13-2805 | 2017-04-14. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. TO IMPROVE HANDLING OF CUSTOMER CONCERNS WITH HANDS-FREE (BLUETOOTH) VEHICLE SYSTEMS, MAZDA LAUNCHED A NEW SERVICE PROCEDURE AND PART EXCHANGE PROGRAM EFFECTIVE FEB. 08, 2010 ON APPLICABLE VEHICLES. DUE TO THE COMPLEXITY OF SOFTWARE AND HARDWARE AVAILABLE ON VARIOUS CELLULAR PHONES AND CELL PHONE PROVIDER NETWORKS, IT IS ESSENTIAL FOR CUSTOMERS TO CONTACT THE MAZDA HANDS-FREE SYSTEM CUSTOMER CARE NUMBER AT (800) 430-0153 OR, FOR CUSTOMERS REQUIRING ADDITIONAL RESOURCES, PLEASE DIRECT THEM TO “WWW.MAZDAUSA.COM/BLUETOOTH.” REPRESENTATIVES OF THE CUSTOMER CARE CENTER ARE KNOWLEDGEABLE ON VERIFYING APPROVED PHONES AND PROPERLY PAIRING (PROGRAMMING) SPECIFIC PHONES TO THE VEHICLE’S BLUETOOTH SYSTEM. THEY ARE ALSO BEST EQUIPPED TO RESOLVE A MAJORITY OF THE PAIRING ISSUES AND OTHER BLUETOOTH RELATED CONCERNS WHEN COMMUNICATING DIRECTLY WITH MAZDA CUSTOMERS. |
| 05-004-13-2800 | 2017-04-14. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME CUSTOMERS MAY COMPLAIN OF A CHECK ENGINE LIGHT AND A/T WARNING LIGHT ON WHEN STARTING THE ENGINE. AT THE SAME TIME, AN ENGINE INSPECTION REQUIRED MESSAGE IS DISPLAYED ON THE LCD. DTC P0722:00 IS STORED IN THE TRANSMISSION CONTROL MODULE (TCM) MEMORY. •DTC P0722:00 (OPEN CIRCUIT IN OUTPUT SPEED SHAFT CIRCUIT)THE TCM CONTROL LOGIC HAS BEEN CHANGED TO ELIMINATE THIS CONCERN. |
| 01-010-13-2775A | 2017-04-14. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. ON CERTAIN SUBJECT VEHICLES, THE MALFUNCTION INDICATOR LIGHT (MIL) MAY ILLUMINATE WITH DTC P0126:00 (THERMOSTAT STUCK OPEN) STORED IN THE POWERTRAIN CONTROL MODULE (PCM) MEMORY. THE THERMOSTAT FUNCTIONS NORMALLY, BUT THE “THERMOSTAT STUCK OPEN” CONDITION IS MISTAKENLY DETECTED DUE TO INAPPROPRIATE PCM SOFTWARE.THIS CONCERN WILL OCCUR UNDER THE FOLLOWING CONDITIONS: •WHEN DRIVING ON HIGHWAYS/FREEWAYS IMMEDIATELY AFTER A COLD START•WHEN THE AMBIENT TEMPERATURE IS 14 TO 32 DEGREES F (-10 TO 0 DEGREES C) •WHEN OPERATING THE HVAC SYSTEM IN THE MAXIMUM AIRFLOW MODE |
| 00-001-13-2748A | 2017-04-14. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. MAZDA HAS DEVELOPED FACTORY RECOMMENDED SCHEDULED MAINTENANCE SERVICES THAT SUPPORT ALL MAJOR VEHICLE SYSTEMS. MAZDA RECOMMENDS DEALERS FOLLOW THE SCHEDULED MAINTENANCE TABLES AS CITED IN THE VEHICLE-SPECIFIC WORKSHOP MANUAL OR OWNER’S MANUAL. SERVICES PERFORMED OUTSIDE OF MAZDA’S FACTORY SCHEDULED MAINTENANCE ARE NOT RECOMMENDED. THESE SERVICES ARE UNNECESSARY AND CREATE UNNEEDED EXPENSES FOR YOUR CUSTOMERS. |
| 01-010-13-2775B | 2017-04-14. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. ON CERTAIN SUBJECT VEHICLES, THE MALFUNCTION INDICATOR LIGHT (MIL) MAY ILLUMINATE WITH DTC P0126:00 (THERMOSTAT STUCK OPEN) STORED IN THE POWERTRAIN CONTROL MODULE (PCM) MEMORY. THE THERMOSTAT FUNCTIONS NORMALLY, BUT THE “THERMOSTAT STUCK OPEN” CONDITION IS MISTAKENLY DETECTED DUE TO INAPPROPRIATE PCM SOFTWARE.THIS CONCERN WILL OCCUR UNDER THE FOLLOWING CONDITIONS: •WHEN DRIVING ON HIGHWAYS/FREEWAYS IMMEDIATELY AFTER A COLD START•WHEN THE AMBIENT TEMPERATURE IS 14 TO 32 DEGREES F (-10 TO 0 DEGREES C) •WHEN OPERATING THE HVAC SYSTEM IN THE MAXIMUM AIRFLOW MODE |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.