WenmarOpen by Wenmar Pro

Service bulletins for the 2021 Jeep Wrangler

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1062 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Backup camera are shown. Show all

Bulletins, newest first
S248A0000162024-12-17. Service bulletin. BACK OVER PREVENTION: REARVIEW SYSTEM BRAKING. Customer complaints regarding rear view camera inoperative or flickering blue radio screen display while transmission is in reverse or blank screens when selecting the rear camera view following a recent service repair involving the removal and installation of the rear spare tire carrier
03002242024-03-18. Service bulletin. EXTERIOR LIGHTING; BACK OVER PREVENTION. Front and Rear Axle Sensor Kit **Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? C1451-11 - Service Axle Locker System** Customers may also comment on a Service Axle Locker message displayed in the Electronic Vehicle Information Center (EVIC) for this condition.
S23190000072024-01-08. Service bulletin. BACK OVER PREVENTION; STEERING:CRITICAL FASTENERS; STEERING. Squeak Noise From Dash Area When Turning The Steering Wheel.
08064232024-01-02. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Radio Over The Air Updating to QR40.12 Software Version Mobile Wi-Fi inoperative upon start up. ? Hotspot gives 9No Internet9 connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.7 to QR40.12. NOTE: National launch for this FOTA update is expected to begin March 10, 2023. DISCUSSION: Vehicles sold in the U.S. and Canada can now receive software updates ?over-the-air?. Updates to software will occur in a phased roll-out. The software is updated through the built-in cellular modem in the radio.
08048232024-01-02. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; BACK OVER PREVENTION; EXTERIOR LIGHTING. Flash: Battery Pack Control Module (BPCM) Diagnostic and System Updates Customers may experience a false Malfunction Indicator Lamp (MIL) illumination related to PHEV battery: ? P1A21-00 - HV Battery Contactor Control Sequence Incorrect. ? P0B3E-00 - Hybrid/EV Battery Voltage Sense 1 Circuit High. ? P0607-00 - ECU Internal Performance. ? P1E1B-00 - Hybrid/EV Battery Side Voltage System Isolation. ? P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed. ? P1C00-00 - Hybrid/EV Battery Voltage Sense 1 Out Of Range Low. ? P1C01-00 - Hybrid/EV Battery Voltage Sense 1 Out Of Range High. ? P1A9B-00 - Hybrid/EV Battery Temperature Sensor 1 Out Of Range High. ? P0BBD-00 - Hybrid Battery Pack Voltage Variation Exceeded Limit. ? P167B-00 - Controlled System Shutdown. ? U1885-00 - Battery Energy Control Module Lost Communication With HCP. ? P0EDD-00 - Hybrid/EV Battery Pack B Deterioration. ? U0111 - Lost Communication With Hybrid Battery Pack Sensor Module. ? P0CA7-00 - Hybrid/EV Battery Discharging Current High. ? P1A0C-00 - Battery Energy Control Module System Voltage Low. This bulletin involves updating the BPCM with the latest available software. NOTE: Additional module flashes are required for this update to be effective, the following modules are all to be updated along with this BPCM update: ? Powertrain Control Module (PCM). ? Integrated Dual Charging Module (IDCM). ? Transmission Control Module (TCM). ? Battery Pack Control Module (BPCM). ? Hybrid Control Processor (HCP), Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM).
S20250000012024-01-02. Service bulletin. EXTERIOR LIGHTING; BACK OVER PREVENTION. Malfunction Indicator Lamp Illumination (MIL). Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.
90033572024-01-02. Service bulletin. BACK OVER PREVENTION. ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
91001342024-01-02. Service bulletin. SERVICE BRAKES; FUEL SYSTEM, GASOLINE; BACK OVER PREVENTION. Engine When replacing a GMET4 long block from a 2021 JL or older, you will need to carry over the injector wiring harness from the original engine, and the Fuel pressure sensor should be replaced with part number: 68212572AB.
91002472023-12-18. Service bulletin. BACK OVER PREVENTION; VEHICLE SPEED CONTROL. ERG Hydraulic Tensioner Before replacing any FEAD components, please check FEAD belt layout as per the engine sales code. Customer complaint may include a noise from under the hood described as a squeal, screech, squeak, chirp or belt-related noise and/or noisy tensioner/pulley. Please refer to SOL# S2309000007.
91001332023-07-31. Service bulletin. BACK OVER PREVENTION. ROCKER ARM ASSY - ROLLER ROCKER Case 1.- Before replacing the intake or exhaust rocker arms due to an abnormal ticking noise, please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head (no need to replace rocker arms). The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. Case 2.- If the INTAKE camshaft or INTAKE rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).
08048232023-04-17. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; EXTERIOR LIGHTING; BACK OVER PREVENTION. Flash: Battery Pack Control Module (BPCM) Diagnostic and System Updates Customers may experience a false Malfunction Indicator Lamp (MIL) illumination related to PHEV battery: ? P1A21-00 - HV Battery Contactor Control Sequence Incorrect. ? P0B3E-00 - Hybrid/EV Battery Voltage Sense 1 Circuit High. ? P0607-00 - ECU Internal Performance. ? P1E1B-00 - Hybrid/EV Battery Side Voltage System Isolation. ? P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed. ? P1C00-00 - Hybrid/EV Battery Voltage Sense 1 Out Of Range Low. ? P1C01-00 - Hybrid/EV Battery Voltage Sense 1 Out Of Range High. ? P1A9B-00 - Hybrid/EV Battery Temperature Sensor 1 Out Of Range High. ? P0BBD-00 - Hybrid Battery Pack Voltage Variation Exceeded Limit. ? P167B-00 - Controlled System Shutdown. ? U1885-00 - Battery Energy Control Module Lost Communication With HCP. ? P0EDD-00 - Hybrid/EV Battery Pack B Deterioration. ? U0111 - Lost Communication With Hybrid Battery Pack Sensor Module. ? P0CA7-00 - Hybrid/EV Battery Discharging Current High. ? P1A0C-00 - Battery Energy Control Module System Voltage Low. This bulletin involves updating the BPCM with the latest available software. NOTE: Additional module flashes are required for this update to be effective, the following modules are all to be updated along with this BPCM update: ? Powertrain Control Module (PCM). ? Integrated Dual Charging Module (IDCM). ? Transmission Control Module (TCM). ? Battery Pack Control Module (BPCM). ? Hybrid Control Processor (HCP), Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM).
S20250000012023-04-17. Service bulletin. BACK OVER PREVENTION; EXTERIOR LIGHTING. Malfunction Indicator Lamp Illumination (MIL). Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.
08-029-232023-02-13. Service bulletin. EXTERIOR LIGHTING; BACK OVER PREVENTION; POWER TRAIN; ELECTRICAL SYSTEM. Flash: Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). P061B-00 - Internal Control Module Torque Calculation Performance. NOTE: P061B-00 DTC may set after driving on snow/ice in 2WD and Traction Control System (TCS) turned off. P06A3-00 - Sensor Reference Voltage 9D9 Circuit/Open. P0697-00 - Sensor Reference Voltage 3 Circuit. Other software enhancement included with this update: On Board Fuel Consumption Monitoring Updates (China Only). **Customers may experience one or more of the following: Vehicle may not be able to enter electric mode driving while Fuel Oil Refresh Mode (FORM) is active. FORM staying on too long.** This bulletin involves reprogramming the HCP and AHCP or also known as Power Inverter Module (PIM) with the latest available software. NOTE: Additional module flashes are required for this update to be effective, the following modules are all to be updated along with this HCP and AHCP update: Powertrain Control Module (PCM). Transmission Control Module (TCM). Battery Pack Control Module (BPCM). Integrated Dual Charging Module (IDCM)
08-022-232023-02-13. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Radio Over The Air Updating to 40.12 Software Version Mobile Wi-Fi inoperative upon start up. Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 39.5 to 40.12.
08090212023-01-17. Service bulletin. EQUIPMENT:ELECTRICAL; BACK OVER PREVENTION:SOFTWARE. UKG Radio Enhancements This bulletin involves updating the radio software level to 2036.07. Customers may experience one or more of the following:Screen flickering. Carplay audio does not always resume. In addition, the following software enhancements are available:Apple certification enhancements. Google certification enhancements.
08089212023-01-17. Service bulletin. EQUIPMENT:ELECTRICAL; BACK OVER PREVENTION:SOFTWARE. UGA and UGG Radio Enhancements This bulletin involves inspecting and if required updating the radio software to 2036.08. Customers may experience one or more of the following: Screen flickering. Carplay audio does not always resume. Battery Save vs. Battery Charge toggles back to Battery Charge after sleep cycle. When ?Charge Now? is selected on key-off outside of the charging schedule, it does nothing. In addition, the following software updates are also available:Apple® certification enhancements. Google® certification enhancements.
24007212023-01-17. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION:SOFTWARE. Flash: HVAC Diagnostic and System Updates This bulletin involves reprogramming the HVAC control module with the latest available software. The customer may notice one or more of the following:Intermittent change of smell or humidity level in vehicle. An intermittent blast of warm air when A/C is on. Intermittent increase of outside air through the HVAC system. In addition, the following software enhancement is also available:Improvements for customer concerns of 'cabin too warm', specifically in the mid ambient temperature range 4.5-15.5 °C (40-60 °F).
S21080001162023-01-17. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Max Regeneration Does Not Remain On After Vehicle Is Restarted
S20230000112023-01-17. Service bulletin. BACK OVER PREVENTION; VISIBILITY; VEHICLE SPEED CONTROL. Wind Noise And Or Gap At Front Door Mirror Flag
S21230000292023-01-17. Service bulletin. BACK OVER PREVENTION. Squeak and or Chirp Noise From Lift Gate Glass
S21080001022023-01-17. Service bulletin. BACK OVER PREVENTION. Reverse Camera System Unavailable Message, Blue Screen Showing On Radio Display
90043752023-01-17. Service bulletin. BACK OVER PREVENTION. RADIO, MULTI Media (ASSY) The customers may have concerns of backup camera missing gridlines or showing black screen with "check entire surroundings" message while in Reverse mode. It is a backup camera initialization timing issue. Please check the backup camera and connections. This issue is recoverable with a key cycle. Replacing the radio head unit will not resolve the customer's concerns. FOTA service software release is scheduled for later June, 2021.
08-003-22 REV. A2023-01-17. Service bulletin. STEERING; EQUIPMENT:ELECTRICAL:INFOTAINMENT; BACK OVER PREVENTION. UAQ and UCQ Radio Enhancements Customers may experience one or more of the following: ? **Wi-Fi hotspot connection failure. ? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Intermittent, black radio display screen (Rear View Camera (RVC) not affected). ? Intermittent, radio freezes (RVC not affected). ? Wireless connectivity pairing and/or connection issues. ? Lost radio presets. ? Radio channels change by itself. ? SXMT icon inoperative. ? SXMT favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Backup camera has black display screen or only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) . ? High pitch chime noise. ? Contact list not loading. ? Device not supported message. ? Remote app inoperative. ? Travel-Link fuel price incorrect. ? Backup camera gridlines missing. ? Unable to adjust volume. In addition, the following enhancement are included in this update: ? Enables map updates. ? Heavy Duty (HD) Truck USB HUB improvements. ? HD Truck heated steering wheel improvements This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.
S20250000062023-01-09. Service bulletin. BACK OVER PREVENTION; EXTERIOR LIGHTING. Malfunction Indicator Lamp (MIL) Illumination. Diagnostic Trouble Code (DTC) P206D ? Reductant Quality Sensor Circuit High Set.
S22230000292023-01-09. Service bulletin. BACK OVER PREVENTION. Rattle Noise From Door

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.