WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Jeep Renegade

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

402 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
18-029-172018-06-11. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Flash: Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software.
03-001-172018-06-11. Service bulletin. VEHICLE SPEED CONTROL. Noise In Front Of Vehicle When Accelerating Or Decelerating This bulletin involves replacing both front half shafts. The customer may describe a clunk type noise in front of the vehicle while accelerating or decelerating.
90036962018-06-11. Service bulletin. STRUCTURE:BODY:DOOR. Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
90036942018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
90036812018-06-11. Service bulletin. SEAT BELTS. Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
90036872018-06-11. Service bulletin. SEAT BELTS. Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
68277402A2018-06-11. Service bulletin. VEHICLE SPEED CONTROL:CRUISE CONTROL. Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
08-065-162018-06-11. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; ELECTRICAL SYSTEM:SOFTWARE. Flash: Amplifier Audio Enhancement This bulletin involves updating the amplifier (AMP) software. The customer may notice a poor audio quality. This condition may happen when the audio volume is at a mid to high output.
RL305553A2018-06-11. Service bulletin. POWER TRAIN. 9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
68105583A2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
18-065-142018-06-11. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM. Flash: MIL Illumination - P1451-00 Set in the ECM Unit This bulletin involves upgrading the software in the Engine Control Module (ECM). The customer may experience MIL light illuminates and DTC P1451-00 ?Diesel Particulate Filter- Efficiency? set in the ECM.
23-035-142018-06-11. Service bulletin. LATCHES/LOCKS/LINKAGES:DOORS:LATCH. Driver Door Lock Cylinder This bulletin involves replacing the driver door lock cylinder housing. The plastic cover of the driver door lock cylinder may be loose or fall off.
08-089-142018-06-11. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; POWER TRAIN. Flash: Multiple ECU Software Enhancements This bulletin involves upgrading the software in the Engine Control Module (ECM), the Instrument Panel Cluster (IPC), the Body Control Module (BCM), the Antilock Brake System (ABS), the Electric Steering Lock Module (ESL) and the HVAC Module. The customer may experience one or all of the following: - Fuel consumption indication on the trip computer could be 2% higher than the real value. - The clock of the Radio and displayed by the EVIC loses time. - Start and Stop is sometime erroneously not available. - Excessive battery consumption while the vehicle is set in Logistic Mode. - DTC P0238 ?Turbo boost Pressure Sensor Circuit High?. MIL light illuminates sometime during WOT acceleration. (2.0L Diesel engine only) - Manual Transmission Gear upshift/downshift indicator shown in the EVIC sometime does not work properly. (1.6L Diesel engine only)
08-034-16 REV. A2018-06-04. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. RL4 Radio Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: · ParkSense audio delay. · Forward Collision Warning (FCW) turns off spontaneously after key on and FCW warning light is on.
90034132018-06-04. Service bulletin. VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
21-021-162018-05-21. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): · **P061B-00 - Internal Control Module Torque Calculation Performance. · P072F-00 - Stuck In Gear 4.** · P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. · P1DAD - Input Shaft-Output Shaft Direction Correlation. · P1CC9 - Unable to Engage Gear. · P1D98 - Incorrect Gear Ratio Clutch B or D Defective. · U1424 - Implausible Engine Torque Signal Received. In addition to correcting the DTCs listed this software update includes the following enhancements: · **Coast down bump on 7-6, 6-5, 5-4, 5-3 downshift improvements. · Cold 1-2, 2-3 upshift improvements. · 1-2, 2-3 upshift flare control improvements. · Power-on upshift improvements. · Lift foot upshift 2-3, 4-5, 8-9 improvements.** · Garage shift improvements (Shifting from Park or Neutral to Drive or Reverse). · 1-2 Shift Quality improvements. · Improved engine performance under certain operating conditions (High Altitude, High Ambient Temperatures and High Humidity). · Hill shift pattern optimization. · Improved redline shift performance. · Improved upshifts, downshifts, coast down shifts and tip shifts.
18-063-162018-05-21. Service bulletin. POWER TRAIN. Flash: 2.4L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Engine Control Module (ECM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) stored in the ECM memory: · **P050D - Cold Start Rough Idle. · P0101 - Mass Air Flow Sensor "A" Circuit Performance. · P0335 - Crankshaft Position Sensor Circuit. · P1CEC - Variable Valve Solenoid Valve Cold Start Closing Position 1 Timing Over-Retard. · P1CED - Variable Valve Timing Solenoid Valve Cold Start Closing Position Timing Over-Advance. · P1607 - PCM Internal Shutdown Timer Rationality. · P0128 - Thermostat Rationality. · P2610 - PCM Internal Engine Off Timer Performance. · P0440 - General EVAP System Failure. · P0441 - EVAP Purge System Performance. · P0456 - EVAP System Small Leak. · P0455 - EVAP System Large Leak. · P0452 - EVAP Pressure Switch Stuck Closed. · P0133 - O2 Sensor 1/1 Slow Response. · C0501 - Wheel Speed Signal Left Front Rationality. · C0507 - Wheel Speed Signal Right Front Rationality. · C050D - Wheel Speed Signal Left Rear Rationality. · C0513 - Wheel Speed Signal Right Rear Rationality. · U0428-00 - Implausible Data Received From Steering Angle Sensor Module. · C0061 - Lateral Acceleration Sensor.** · U0402 - Implausible Data Received From TCM. · P0133 - O2 Sensor 1/1 Slow Response. · P050D - Cold Start Rough Idle. In addition, customers may experience one or more of the following concerns: · RPM flare at cold start. · Less than desired idle performance. · Cold engine RPM surge with gear engagement.
14-003-162018-05-21. Service bulletin. FUEL SYSTEM, GASOLINE. Replace Fuel Pump This bulletin involves replacing the fuel pump module. Some vehicles may have been built with a fuel pump that can cause a no start condition on vehicles with low mileage (Usually less than 100 miles).
14-003-16 REV. A2018-05-21. Service bulletin. FUEL SYSTEM, GASOLINE. Replace Fuel Pump This bulletin involves replacing the fuel pump module. Some vehicles may have been built with a fuel pump that can cause a no start condition on vehicles with low mileage (Usually less than 100 miles).
06106092A$2018-05-14. Service bulletin. SEATS. Seat Relay For a Jeep Renegade or Fiat 500X ONLY, if the driver's power seat will not move in any axis and the key is in the on position with the door open: 1. Please take a Vehicle Scan Report, taking note of any active or stored DTC's, especially in the Body Control Module (BCM). 2. Before replacing the relay, call Rick Gordon at cell (248) 630-6281. If no answer leave a message and if after 15 minutes, there is no return call, proceed with the repair. 3. In the event there is no call-back, please email the Vehicle Scan Report to rick.gordon@fcagroup.com
68321236A$2018-03-13. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. RF Hub Module DTC, U1765-87 "RFHM (Radio Frequency Hub Module) - Missing Message" may appear in a stored state on a ignition power cycle. No troubleshooting or parts replacement is necessary if this code is stored as the system is functioning to design.
08-021-16 REV. A2018-03-13. Service bulletin. INTERIOR LIGHTING; LATCHES/LOCKS/LINKAGES; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES. Flash: BCM Diagnostic And System Improvements This bulletin involves reprogramming the Body Control Module (BCM) with the latest available software. The customer may describe one or more of the following: · **Rear interior overhead lamps remain illuminated after exiting vehicle and locking from the driver's or passenger's door lock buttons. This is causing the vehicle battery to go dead.** · The door locks are inoperative when locking/unlocking remotely. · False activation of the vehicle security alarm. · False exterior light failure messages being displayed in the instrument cluster.
90025192018-02-21. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. 82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
09-003-162017-11-03. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. Turbocharger Replacement This bulletin involves replacing the turbocharger and repositioning the control solenoid valve air intake filter. The customer may describe a drop in vehicle performance and/or a malfunction indicator light (MIL) illuminated. The following Diagnostic Trouble Codes (DTCs) will also be stored or active: · P2564 - 00 - Variable Geometry Turbocharger Position Sensor Deviation Signal Amplitude Less Than Minimum. · P2565 - 00 - Variable Geometry Turbocharger Position Sensor Deviation Signal Amplitude Greater Than Maximum.
08-009-162017-11-03. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; ELECTRICAL SYSTEM; EQUIPMENT. Radio Software Enhancements This bulletin involves updating the radio's software. A customer may experience one or more of the following: · Radio display screen intermittently may go blank. · Radio display screen may lock up. · Back up display may not turn off. · Loss of radio memory for skipped channels or incorrectly displaying skipped channels in the menu list. · Korean language was not supported (APAC - Korea only). Additional Enhancements: · Removed the charging schedule from showing in the setting menu (FF BEV only). · Adding Korean language support (APAC - Korea only).

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.