Service bulletins for the 2014 Jeep Grand Cherokee
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
634 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| 18-096-15 | 2019-05-20. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; POWER TRAIN; ENGINE. Flash: Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience one or more of the symptoms/conditions listed below or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set. If any of the following DTCs have been set perform the Diagnosis: - U0140 - Lost Communication With Body Control Module. Attempting to clear this DTC will be unsuccessful. - P0300 - Multiple Cylinder Misfire (only applies to 5.7L engines). - P0573 - Brake Switch 1 Stuck Off. The following powertrain system improvements/enhancements are also included in this software release: - Corrected a generic scan tool display issue regarding Mode 6 data accuracy. - Improved transmission Quick Learn routine performance (only applies to 5.7L engines). |
|---|---|
| 18-094-15 | 2019-05-20. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN; ENGINE. Flash: 3.0L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latestavailable software. It also involves the cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 and/or Catalyst Temperature Sensor if necessary depending on Diagnostic Trouble Codes (DTCs) that may have set. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Codes may have been set: ? P1296-00 - EGR Slow Response - Increasing Flow. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P2237-00 - O2 Sensor 1/1 Pump Cell Current Circuit Open. ? P24D1-00 - Particulate Matter Sensor Regeneration Incomplete. ? U0422-00 - Implausible Data Received From Body Control Module. ? P1E0C-00 - Empty Fuel Tank. ? P2463-00 - Diesel Particulate Filter - Soot Accumulation. ? P24A4-00 - Particulate Filter Restriction - Soot Accumulation Too High. ? P241D-00 - Scr Inducement - Forced Engine Shutdown. ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P208B-00 - Reductant Pump 1 Control Performance. ? P0087-00 - Fuel Rail Pressure Too Low. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. ? P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. ? P1289-00 - NOX Sensor 1/2 Zero Offset Too Low. ? P2BA9-00 - NOX Exceedence - Insufficient Reagent |
| 09-006-15 REV A | 2019-05-20. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING. Intermittent Engine Shudder While Driving This bulletin involves replacing the engine cylinder heads. A small number of customers may experience a slight engine shudder while driving. They may state that the condition feels and sounds like driving over rumble strips. It may also be perceived as an internal transmission issue or engine misfire. No Diagnostic Trouble Codes (DTCs) will set as a result of this condition. DISCUSSION: The root cause of the engine shudder has been found to be due to excess carbon build-up on the exhaust valve stems and will typically happen on vehicles driven mostly in light load conditions. As a result, new cylinder heads have been released that are equipped with newly designed valve stem seals. These newly designed seals are designed to help prevent excessive carbon from building up on the valve stems. Although it may be hard to reproduce, engine shudder resulting from these excess carbon deposits, will typically only happen under the following driving conditions: ? Steady speeds between 50 and 70 mph (80 and 113 kph). ? Engine speed between 1600 - 2000 RPM. ? Present during engine warm up to operating temperature after a cold soak. ? Only present for a few seconds at a time and often during a 6-7 upshift. ? Light load acceleration or while driving up a slight grade. ? Symptom will go away either by aggressively applying the accelerator pedal or going into a zero throttle deceleration. |
| 5QV32DX9A | 2019-05-20. Service bulletin. STEERING. Part Description: STEERING WHEEL - STEERING Issue Description: Do not replace Steering Wheel due to heating temperature concern.~ Engineering is working on software update to address this customer concern.~ |
| 5QX861W1A | 2019-05-20. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. Part Description: Leather Instrument Panel Issue Description: If replacing the instrument panel top cover because of what appears to be a wrinkle or thread in the leather near the A-pillar, then please call Mike Wicker at Cell (248) 821-9350. Chrysler wants to learn more about these conditions. A photo of the condition would be beneficial and can be sent to MDW12@chrysler.com. If no response is received within 15 minutes, then proceed with the required repair. |
| 08-103-15 | 2018-12-17. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT. RG3 RG4 RJ3 RJ4 Radio Enhancements This bulletin involves inspecting and updating the radio software, if required. ? Duplicate song titles may be displayed in USB mode. ? Last track is displayed but next track is being played. ? SD, USB or BTSA modes may become non-functional for a given ignition cycle. ? Track names may be displayed twice in USB or SD media modes. ? Voice Recognition command ?Set Temperature? may not respond in Fahrenheit. United Kingdom (UK) Vehicle only. ? DAB (Digital Audio Broadcast) is inoperative. ? Wrong routing for addresses with a longitude between 0 and -1 degrees. ? Speed Camera UK & Spain complaining that the speed camera feature was not available with the latest MY14 software. ? DAB preset list on the top of the screen doesn't change while scrolling with steering controls. ? Rear view camera jitter. ? Tuner reception software enhancements. ? HVAC temperature control enhancements. ? SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). ? Battery drain due to the radio and cluster back-lighting staying on. ? Postal Code smart speller logic enhancements (EMEA markets only). ? AM/FM steering wheel mode switch button not working (LATAM markets only). ? Navigation Lockout Disable while vehicle is in motion (EMEA markets only). ? Removed network status indicators for SRT/APPS. ? Voice Recognition (VR) says 'cancel' when starting (App) applications. ? iPod would not resume playing after a VR session or phone call. ? Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. ? rear camera may show a black screen for 3 seconds upon going to reverse. ? Navigation would not start or would lose position. ? Removal of parental control under Apps menu. ? Turn by Turn navigation in the cluster set to ON by default. ? Transfer button does not pick-up and transfer incoming call. ? Some Russian letters are caps when they sho |
| 08-100-15 | 2018-12-17. Service bulletin. ELECTRICAL SYSTEM:STARTER ASSEMBLY; STRUCTURE:BODY:HATCHBACK/LIFTGATE; ELECTRICAL SYSTEM. Flash: Radio Frequency Hub Module (RFHM) Enhancement This bulletin involves updating the Radio Frequency Hub Module (RFHM) software. The customer may experience one or both of the following condition: ? Vehicle will not start. If the backup start mode is tried (press the FOB against the Start/Stop button) a message in the cluster will be displayed ?Key Not Detected?. ? The power liftgate intermittently may not open. It may be required to press the power liftgate button on the FOBIK two more times to open the power liftgate. |
| 24-005-15 | 2018-12-17. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Flash: Temperature Control Enhancement This bulletin involves reprogramming the HVAC Module with new software. Customers may experience the following condition: ? Vehicle cabin temperature seems too warm even after reducing the Automatic Temperature Control setpoint. ? Heat mode becomes active when the radio is configured to read in °C and cabin temperature is set to LO. Updating the HVAC software will correct these conditions. |
| 18-023-15 REV-C | 2018-12-17. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: 3.0 L MIL Illumination Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. It also involves the cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 and/or Catalyst Temperature Sensor if necessary depending on Diagnostic Trouble Codes (DTCs) that may have set. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Code(s) may have been set: ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P241D-00 - Scr Inducement - Forced Engine Shutdown. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P208B-00 - Reductant Pump 1 Control Performance. ? P0087-00 - Fuel Rail Pressure Too Low. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. ? P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. ? P1289-00 - NOX Sensor 1/2 Zero Offset Too Low. ? P1296-00 - EGR Slow Response - Increasing Flow. ? P2BA9-00 - NOX Exceedence - Insufficient Reagent Quality. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 2. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance Bank 1 Sensor 1. ? P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 3. ? P062B-00 - Internal Control M |
| 08-016-15 REVA | 2018-12-10. Service bulletin. ELECTRICAL SYSTEM. Poor Radio Reception This bulletin involves replacing the satellite antenna if needed. A customer may experience, SXM (Sirius/XM) radio has intermittent muting. This occurs in areas where XM signal is degraded and cell signal is very weak. The condition happens when the optional vehicle internet connection through the cell network is in use with the internal vehicle Wi-Fi. This Symptom/Condition Only Applies to 2014-2015 WD, WK or KL Vehicles. A customer may experience a popping noise when listening to AM stations. |
| 08-067-15 | 2018-12-10. Service bulletin. ELECTRICAL SYSTEM. RM4 Radio Enhancements (Japan Only) This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: ? Digital TV, television display screen may be blurry. ? Song names displayed twice in USB and SD media modes. ? Radio may displays or voice prompt ?Please check ETC device? (Electronic Toll Collection). ? Poor navigation guides through overpass or underpasses, multi-level intersections. ? Navigation Turn-by-turn guidance setting may be cleared after ignition is cycled. ? Navigation may reset while driving. |
| 05-002-15 | 2018-12-10. Service bulletin. SERVICE BRAKES, HYDRAULIC; SERVICE BRAKES, AIR:DISC:CALIPER; SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:CALIPER. Front Brake Squeak/Squeal Noise This bulletin involves replacing the front brake caliper guide pin bushings. The customer may describe a front brake squeak/squeal noise at cold temperatures or with cold brakes after sitting. Noise is most prevalent during a low-speed stop with light brake pedal effort. |
| 09-006-15 | 2018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. Intermittent Engine Shudder While Driving This bulletin involves replacing the engine cylinder heads. A small number of customers may experience a slight engine shudder while driving. They may state that the condition feels and sounds like driving over rumble strips. It may also be perceived as an internal transmission issue or engine misfire. No Diagnostic Trouble Codes (DTCs) will set as a result of this condition. DISCUSSION: The root cause of the engine shudder has been found to be due to excess carbon build-up on the exhaust valve stems and will typically happen on vehicles driven mostly in light load conditions. As a result, new cylinder heads have been released that are equipped with newly designed valve stem seals. These newly designed seals are designed to help prevent excessive carbon from building up on the valve stems. Although it may be hard to reproduce, engine shudder resulting from these excess carbon deposits, will typically only happen under the following driving conditions. ? Steady speeds between 50 and 70 mph (80 and 113 kph). ? Engine speed between 1600 - 2000 RPM. ? Present during engine warm up to operating temperature after a cold soak. ? Only present for a few seconds at a time and often during a 6-7 upshift. ? Light load acceleration or while driving up a slight grade. ? Symptom will go away either by aggressively applying the accelerator pedal or going into a zero throttle deceleration. |
| 08-072-15 | 2018-12-03. Service bulletin. EQUIPMENT. RA3 RA4 Radio Enhancements This bulletin involves inspecting and updating the radio software, if required. A customer may experience, one or more of the following conditions. ? Improved Radio security protection to reduce the potential risk of unauthorized and unlawful access to vehicle systems (U.S. Market Only). ? Track names may be displayed twice in USB or SD media modes. ? SD, USB or BTSA modes may become non-functional for a given ignition cycle. ? Duplicate song titles may be displayed in USB mode. ? Last track is displayed but next track is being played. ? Navigation function may resets itself after using One-Shot Voice Recognition (VR). ? Intermittently the Global Positioning System (GPS) may lose it?s location for a short time and causes routing and positioning concerns. ? GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. ? A false Pop-up message may appear ?Vehicle Phone Requires Service? even though the vehicle?s phone works properly. ? Back-up camera image may be unclear or jittery/stutters at times. ? Enables Via Mobile software features when released to consumers. (U.S. market only) ? Able to adjust audio balance / fade settings during a VR session. ? Correct, condition where user could not exit screen off mode. ? Mute button status was not being displayed correctly. ? Presets where not shown correctly or were deleted. ? Enhancements to POI. ? ParkSense tone continuously on. ? Enhancement to navigation routing. ? Radio display may shows ?Please insert USB Stick?. ? Enhancement made when video is display in radio when using PAL format video disks. ? Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. ? Navigation may not start or may lose position. ? Rear camera may show a black screen for 3 seconds upon going to reverse. ? Enhancements for iPod or iPhone devices that may not start playing after connec |
| 05-006-15 | 2018-12-03. Service bulletin. SERVICE BRAKES. Front Brake Squeak/Squeal Noise This bulletin involves replacing the front brake rotors. The customer may describe a high frequency front brake squeal or squeak, at approximately 8.4kHz. Noise may be intermittent, so not always possible to duplicate. |
| 09-010-15 | 2018-11-26. Service bulletin. ENGINE. Incorrect 5.7L Engine Oil Dipstick This bulletin involves installing the correct engine oil indicator (Dipstick). The customer may notice blue smoke coming from the tail pipe after the vehicle was started. Also after performing an oil change the Dipstick may indicate the oil was low. When changing the oil and filter, service information shows 7 quarts / 6.6 liters are required. After installing 7 quarts / 6.6 liters the Dipstick may indicate the engine oil level is 1 quart / .95 liters low. |
| 09-008-15 | 2018-11-26. Service bulletin. ENGINE. 3.6L Oil Loss Diagnostic Aid This bulletin involves additional information on oil loss. |
| 08-072-15 REV-A | 2018-11-26. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. RA3 RA4 Radio Enhancements This bulletin involves inspecting and updating the radio software, if required. A customer may experience, one or more of the following conditions. ? Track names may be displayed twice in USB or SD media modes. ? SD, USB or BTSA modes may become non-functional for a given ignition cycle. ? Duplicate song titles may be displayed in USB mode. ? Last track is displayed but next track is being played. ? Navigation function may resets itself after using One-Shot Voice Recognition (VR). ? Intermittently the Global Positioning System (GPS) may lose it?s location for a short time and causes routing and positioning concerns. ? GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. ? A false Pop-up message may appear ?Vehicle Phone Requires Service? even though the vehicle?s phone works properly. ? Back-up camera image may be unclear or jittery/stutters at times. ? Enables Via Mobile software features when released to consumers. (U.S. market only) ? Able to adjust audio balance / fade settings during a VR session. ? Correct, condition where user could not exit screen off mode. ? Mute button status was not being displayed correctly. ? Presets where not shown correctly or were deleted. ? Enhancements to POI. ? ParkSense tone continuously on. ? Enhancement to navigation routing. ? Radio display may shows ?Please insert USB Stick?. ? Enhancement made when video is display in radio when using PAL format video disks. ? Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. ? Navigation may not start or may lose position. ? Rear camera may show a black screen for 3 seconds upon going to reverse. ? Enhancements for iPod or iPhone devices that may not start playing after connecting. ? iPod would not resume playing after a VR session or phone call. ? Radio reset, screen lockup, blank screen or sluggish system respo |
| 08-056-15 | 2018-11-26. Service bulletin. STRUCTURE:BODY:HOOD. Improper Hood Switch Operation This bulletin involves performing a Body Control Module (BCM) Proxi Configuration and Proxi Alignment. The customer may notice that the security alarm will not sound when the hood is opened. |
| 18-023-15 REVA | 2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. Flash: 3.0 L MIL Illumination Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Code(s) may have been set: ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P241d-00 - Scr Inducement - Forced Engine Shutdown. ? P0087-00 - Fuel Rail Pressure Too Low. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P0171-00 - System Too Lean (Bank 1). ? P0172-00 - System Too Rich (Bank 1). ? P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. ? P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. ? P1289-00 - NOX Sensor 1/2 Zero Offset Too Low. ? P1296-00 - EGR Slow Response - Increasing Flow. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P2BA9-00 - NOX Exceedence - Insufficient Reagent Quality. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 2. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance Bank 1 Sensor 1. ? P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 3. ? P062B-00 - Internal Control Module Fuel Injector Control Circuit Performance. ? P0088-00 - Fuel Rail Pressure Too High. ? P016F-00 - Closed Loop fuel Pressure Control At Limit - Pressure Too Low. ? P009A-00 - Intake Air Temperature / Ambient Ai |
| 18-044-15 | 2018-11-26. Service bulletin. ELECTRICAL SYSTEM. Flash: Power Control Module Software Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The customers may experience one or all of the following: - Customer may experience a "detonation" type of noise while accelerating or at idle. - Customers may experience Cruise Control lock out (inoperative) after several ?+? cruise button inputs attempting to increase Cruise Set Speed. Turning the ignition off and back on will clear the condition. - MIL light illuminates and DTC P2463-00 ?Diesel Particulate Filter- Soot Accumulation? set in the PCM. The software is also being released to improve A/C compressor relay duty cycle operation to prevent ignition off battery draw. |
| 21-033-15 | 2018-11-26. Service bulletin. POWER TRAIN. Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software followed by a drive validation. The following software enhancement, for the 948TE 9-speed transmission, is being released to improve diagnostics for the following Diagnostic Trouble Codes (DTCs): ? P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance ? P0887 - TCM Power Control Circuit High ? P1720 - Output Speed Sensor-Wheel Speed Rationality ? P1D98 - Incorrect Gear Ratio Clutch B or D Defective ? P215C - Output Shaft Speed Wheel Speed Correlation ? U0401 - Implausible Data Received From ECM-PCM The software also enables DTC P07A7 - Transmission Friction Element C Stuck On to set in the case of a dislodged C-clutch snap-ring. |
| 21-005-15 REVA | 2018-11-26. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) and Transmission Control Module (TCM) with new software. NOTE: Both the PCM and TCM must be up to date for these changes to be effective. |
| 18-064-15 | 2018-11-19. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 This bulletin involves replacing the Selective Catalyst Reduction (SCR) Catalyst assembly. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find Diagnostic Trouble Code (DTC) P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 set in the Powertrain Control Module (PCM) memory. |
| 08-091-15 | 2018-11-19. Service bulletin. ELECTRICAL SYSTEM. Flash: ECM and IPC Software Enhancements This bulletin involves upgrading the software in the Engine Control Module (ECM) and if required the Instrument Panel Cluster (IPC). The customer may experience one or all of the following: ? The ?Engine Stop Start Not Available? displayed in the Instrument Cluster after disconnecting the vehicle?s battery. ? The engine fails to start at the first attempt using the Keyless Ignition Node (KIN) button. ? IPC may display the wrong translations in all languages (APAC Market excluded). ? Confusing the vehicle start logic condition based on the vehicle standing in the Start and Stop mode. ? ?Stop/Start Not Ready-Battery Charging? maybe displayed erroneously. ? ?Low Battery Voltage? text message shown erroneously in the EVIC. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.