WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Jeep Grand Cherokee

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

634 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
724982022-09-26. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR. SAFETY RECALL W58 - LOSS OF CRANK POSITION Overlap with V08/V11/V16 Population
S21090000102022-09-15. Service bulletin. ENGINE. 3.0L Ecodiesel Engine Oil Information
09-004-172022-09-15. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Intermittent Engine Shudder While Driving This bulletin involves replacing the engine cylinder heads. A small number of customers may experience a slight engine shudder while driving. They may state that the condition feels and sounds like driving over rumble strips. It may also be perceived as an internal transmission issue or engine misfire. No Diagnostic Trouble Codes (DTCs) will set as a result of this condition.
R692022-09-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. The Selective Catalytic Reduction (SCR) catalyst on about 11,400 of the above vehicles is experiencing washcoat degradation, which may lead to the exceedance of exhaust emission standards.
14-008-212022-08-22. Service bulletin. FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR. 3.0L Diesel Crankshaft Tone Wheel Loss of Signal - X95 Warranty Extension This bulletin involves replacing the crankshaft tone wheel. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set :P0335-00 - Crankshaft Position Sensor Circuit. P0336-00 - Crankshaft Position Sensor Performance. Customers may also comment the following:The vehicle will not accelerate quickly over 80 kph (50 mph) (vehicle is in limp mode). This symptom/condition is cause from missing magnetic material on the crankshaft tone wheel
S18180000242022-08-22. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. Diesel Fuel Injector Cleaning Procedure
S21090000102022-08-22. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION: OIL COOLER. 3.0L Ecodiesel Engine Oil Information
68105583A2022-08-22. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:FILTER/SCREEN. Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
18-045-142022-08-22. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; FUEL SYSTEM, DIESEL. P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 This bulletin involves verifying the proper operation of the Diesel Exhaust Fluid (DEF) system and, if necessary, replacing the Selective Catalyst Reduction (SCR) Catalyst assembly. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find Diagnostic Trouble Code (DTC) P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 set in the Powertrain Control Module (PCM) memory..
18-018-14 REV. B2022-08-22. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P0088-00 - FUEL RAIL PRESSURE TOO HIGH ? P016F-00 - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P05F8-00 REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B-00 - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B-00 - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P0128-00 - THERMOSTAT RATIONALITY ? P1D30-00 - OIL VISCOSITY TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P203E-00 - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20BE-00 - REDUCTANT PRESSURE LINE HEATER CONTROL CIRCUIT PERFORMANCE ? P20EE-00 - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P20C2-00 - REDUCTANT HE
18-034-14 REV. A2022-08-15. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT; ELECTRICAL SYSTEM. P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit
18-018-14 REV. C2022-08-15. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; ENGINE AND ENGINE COOLING. Flash: MIL Illumination - Remote Start, Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Remote Start will not start the vehicle in cold 14° F (-10° C) ambient temperatures. Software enhancements will help this issue. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P0088-00 - FUEL RAIL PRESSURE TOO HIGH ? P016F-00 - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P05F8-00 REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B-00 - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B-00 - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P0128-00 - THERMOSTAT RATIONALITY ? P1D30-00 - OIL VISCOSITY TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P203E-00 - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUI
18-023-15 REV.C2022-08-08. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. Flash: 3.0 L MIL Illumination Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. It also involves the cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 and/or Catalyst Temperature Sensor if necessary depending on Diagnostic Trouble Codes (DTCs) that may have set. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Code(s) may have been set: P20C2-00 - Reductant Heater 3 Control Circuit Performance. P204F-00 - Reductant System Performance. P20E9-00 - Reductant Pressure Too High. P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. P1288-00 - NOX Sensor 1/2 Zero Offset Too High. P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. P241D-00 - Scr Inducement - Forced Engine Shutdown.P0420-00 - Catalyst Efficiency (Bank 1). P1297-00 - EGR Slow Response - Decreasing Flow. P208B-00 - Reductant Pump 1 Control Performance. 0087-00 - Fuel Rail Pressure Too Low. P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. P1289-00 - NOX Sensor 1/2 Zero Offset Too Low. P1296-00 - EGR Slow Response - Increasing Flow. P2BA9-00 - NOX Exceedence - Insufficient Reagent Quality. P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 2. P0426-00 - Catalyst Temperature Sensor Circuit Performance Bank 1 Sensor 1. P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 3. P062B-00 - Internal Control M
17-004-132022-07-25. Service bulletin. SUSPENSION:REAR:SPRINGS:AIR SUSPENSION SYSTEM; ENGINE AND ENGINE COOLING; EQUIPMENT; ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC). Cleaning Of Rear Air Suspension At Every Engine Oil Change This bulletin involves cleaning the left and right side rear air spring bellows and piston area at the lower control arm pocket in the rear of the vehicle. Rear suspension air springs may become damaged due to abrasion from road debris or the air spring can become punctured due to ice/snow build-up at bottom of piston at lower control arm.
18-023-15 REV.C2022-07-25. Service bulletin. FUEL SYSTEM, DIESEL; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE; EQUIPMENT; FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE). Flash: 3.0 L MIL Illumination Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. It also involves the cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 and/or Catalyst Temperature Sensor if necessary depending on Diagnostic Trouble Codes (DTCs) that may have set. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Code(s) may have been set: ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P241D-00 - Scr Inducement - Forced Engine Shutdown. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P208B-00 - Reductant Pump 1 Control Performance. ? P0087-00 - Fuel Rail Pressure Too Low. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. ? P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. ? P1289-00 - NOX Sensor 1/2 Zero Offset Too Low. ? P1296-00 - EGR Slow Response - Increasing Flow. ? P2BA9-00 - NOX Exceedence - Insufficient Reagent Quality. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 2. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance Bank 1 Sensor 1. ? P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 3. ? P062B-00 - Internal Control M
S1709000010 Rev.2022-07-18. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
S18090000072022-05-31. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION. Customer Complaint May Include Engine Oil Leak Or Consumption
S22090000032022-05-31. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. Complete Engine Assembly Replacements Arriving Without Engine Wiring Harness.
S1709000010 RevB2022-05-31. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
R692022-04-04. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; EQUIPMENT. The Selective Catalytic Reduction (SCR) catalyst on about 11,400 of the above vehicles is experiencing washcoat degradation, which may lead to the exceedance of exhaust emission standards.
S1809000007 Rev.2021-06-28. Service bulletin. ENGINE AND ENGINE COOLING. Customer Complaint May Include Engine Oil Leak Or Consumption
S1809000007 Rev.2021-04-26. Service bulletin. ENGINE AND ENGINE COOLING. Customer complaint may include engine oil leak/consumption.
90033572021-04-26. Service bulletin. ENGINE AND ENGINE COOLING. ADAPTER, Engine Oil Filter (Pentastar V6) All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
724982021-03-15. Service bulletin. ENGINE AND ENGINE COOLING. SAFETY RECALL W58 - LOSS OF CRANK POSITION Overlap with V08/V11/V16 Population
S1709000010 Rev.2021-02-16. Service bulletin. ENGINE AND ENGINE COOLING. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.