WenmarOpen by Wenmar Pro

Service bulletins for the 2022 Jeep Gladiator

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

458 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
1132712026-07-18. Service bulletin. ENGINE. CORE – HEATER
1132702026-07-18. Service bulletin. ENGINE. CORE – HEATER
S26090000092026-07-02. Service bulletin. ENGINE. Check Engine Light (CEL) Illuminated with Diagnostic Trouble Code (DTC) P0106 Manifold Absolute Pressure Sensor Performance Setting In The Powertrain Control Module (PCM)
1128422026-07-02. Service bulletin. ENGINE. BOLT - HEX FLANGE HEAD
18-007-26 REV B2026-04-22. Service bulletin. ENGINE; POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0301 - Cylinder 1 Misfire (Active or Stored status set during cold start catalyst heating). ● P0302 - Cylinder 2 Misfire (Active or Stored status set during cold start catalyst heating). ● P0303 - Cylinder 3 Misfire (Active or Stored status set during cold start catalyst heating). ● P0304 - Cylinder 4 Misfire (Active or Stored status set during cold start catalyst heating). ● P0305-00 - Cylinder 5 Misfire (Active or Stored status set during cold start catalyst heating). ● P0306-00 - Cylinder 6 Misfire (Active or Stored status set during cold start catalyst heating).** ● P0300 - Multiple Cylinder Misfire. ● P0032 - O2-Sensor 1/1 Heater Circuit High. ● P0038-02 - O2-Sensor 1/2 Heater Circuit High. ● P0052-02 - O2-Sensor 2/1 Heater Circuit High. ● P0058-02 - O2-Sensor 2/2 Heater Circuit High. ● P0132-02 - O2 Sensor 1/1 Circuit High. ● P0138-02 - O2 Sensor 1/2 Circuit High. ● P0152-02 - O2 Sensor 2/1 Circuit High. ● P0158-02 - O2 Sensor 2/2 Circuit High. ● P2100 - Electronic Throttle Control Motor Circuit. ● P2107 - Electronic Throttle Control Module Processor. ● P0129 - Barometric Pressure Out Of Range Low. China Market Only ● P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation. (Manual Transmission Only). ● P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation. ● P1129 - Closed Loop Fueling Not Achieved - Bank 2 Upstream. Customers may also comment on one or more of the following: ● **The vehicle has a rough idle. ● The engine has a miss. ● Noisy valvetrain.** J18 FSAR-TSB-7200 -2- ● "Service Transmission" message in the Instrument Panel Cluster (IPC) due to clutch slip detection with the transfer case in neutral (Manual Transmission Only). NOTE: Customers might experience wheel spin or slippage and the PCM could
18-044-262026-03-25. Service bulletin. ENGINE. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi
S25090000092025-11-05. Service bulletin. ENGINE. Engine Oil Leak
91006702025-10-02. Service bulletin. ENGINE. Data collection required for all 2020-2026MY vehicles with 3.6L PSU engines during any of their first 3 engine oil changes. This data collection is applicable to all vehicle with engines with sales codes: ERG, ERC, EH3 and ERF. To assist with monitoring and quality improvement of the 3.6L engine, every time a vehicle comes for any of the first 3 oil changes, please use wiTECH to record the total engine idle time and the total engine runtime. 1. Prior to perform the oil change connect wiTECH diagnostic tool. 2. Navigate to the topology screen on the action item section. 3. Once the topology screen loads, disconnect wiTECH and continue with oil change.
S2509000001 REV.B2025-07-31. Service bulletin. ENGINE. Engine Rattle Noise
1056482025-07-23. Service bulletin. ENGINE. MODULE - ENGINE CONTROLLER
91006242025-07-17. Service bulletin. ENGINE. Verify Reman part number availability. Order the "R" part number for all orders:
91006222025-07-09. Service bulletin. ENGINE. When replacing a camshaft and parts kit (P/N 68661146xx and/or 68661147xx), it is NOT necessary to order the roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.
91006142025-06-26. Service bulletin. ENGINE. ADJUSTER Valve Lash Customer's complaint may include a ticking noise coming from the engine. Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.
09-015-252025-06-18. Service bulletin. ENGINE. "Spark Knock/Engine Symptoms Customers may experience the following: ● Knocking or pinging noise coming from the engine upon acceleration. This bulletin involves cleaning the piston heads and cylinder head combustion chambers to resolve a spark knock condition being caused by oil intrusion through the PCV system."
09-011-252025-05-20. Service bulletin. ENGINE. "Misfire Diagnostic Trouble Codes (DTCs), Rough Idle, Valvetrain Noise Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0301 - Cylinder 1 Misfire. ● P0302 - Cylinder 2 Misfire. ● P0303 - Cylinder 3 Misfire. ● P0304 - Cylinder 4 Misfire. ● P0305 - Cylinder 5 Misfire. ● P0306 - Cylinder 6 Misfire. Customers may comment on one or more of the following: ● Rough idle. ● Valvetrain noise. "
9100498 Rev 32025-05-19. Service bulletin. ENGINE. 3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. Refer to SOL # S2509000004. It is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software.
08-099-252025-04-08. Service bulletin. ENGINE; ELECTRICAL SYSTEM. "Camshaft Sensor DTC Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0341 - Camshaft Position Sensor - Performance Bank 1 - Sensor 1. This bulletin involves repairing the cam sensor harness and re-routing the generator wiring."
S25090000042025-04-03. Service bulletin. ENGINE. Misfire DTCs, Rough Idle, Valvetrain Noise
S25090000022025-03-07. Service bulletin. ENGINE. Engine Noise
9100498 REV 12025-03-05. Service bulletin. ENGINE. 3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.
S25090000012025-02-22. Service bulletin. ENGINE. Engine Rattle Noise
09-003-252025-02-20. Service bulletin. ENGINE. "Oil Leaking From Oil Filter Area Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may comment on the following: ● Oil found on the ground beneath the vehicle. "
91004982025-02-12. Service bulletin. ENGINE. "3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."
1011402024-10-18. Service bulletin. ENGINE. FCA Caribbean Warranty Bulletin ID-23-03 Rev. G 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 (Current) Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification
1011372024-10-18. Warranty extension. ENGINE. Warranty Bulletin D-23-04 Rev. F 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.