WenmarOpen by Wenmar Pro

Service bulletins for the 2019 Jeep Cherokee

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

407 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Fuel system are shown. Show all

Bulletins, newest first
18-161-222023-01-17. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; BACK OVER PREVENTION; VEHICLE SPEED CONTROL; EXTERIOR LIGHTING. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or moreof the following DTCs have been set: P02EE - Cylinder 1 Injector Circuit Performance. P02EF - Cylinder 2 Injector Circuit Performance. P02F0 - Cylinder 3 Injector Circuit Performance. P02F1 - Cylinder 4 Injector Circuit Performance. P2C90 - Crankcase Ventilation System - Hose "A" Disconnected. P1D73 - AGS performance fault. P04FC - Crankcase Ventilation System Performance. P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation(Enlarged Europe and Middle East/Africa) only equipped with Gas ParticulateFilter (GPF))(DTC will set when driving above 72 kph (45 mph). P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P050B - Cold Start Ignition Timing Performance. P258B - Electric Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P2B95 - Cold Start Injection Pulse Performance. P062A - Fuel Pump Control Performance. P058C - Battery Monitor Module Temperature Monitoring Performance. P0607 - ECU Internal Performance. Injector performance faults for cylinders 2 - 4 map to DTC for incorrect cylinders. In addition the following software enhancement are included: AGS stuck condition (The customer won't see an issue, but this calibrationallows AGS performance fault - P1D73, to work correctly). Software corrects an issue with the wrong cylinder identification if an injectorcircuit performance fault is set in the PCM: If any of the series of injector control circuit faults are set, please refer tothe bullet-pointed list below to determine which injector to address.
18052202023-01-09. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; BACK OVER PREVENTION; ENGINE AND ENGINE COOLING; EXTERIOR LIGHTING; VEHICLE SPEED CONTROL. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set:P04FC - Crankcase Ventilation System Performance. P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation(EMEA only equipped with Gas Particulate Filter (GPF))(DTC will set when driving above 72 kph (45 mph). P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P050B - Cold Start Ignition Timing Performance. P258B - Electric Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P2B95 - Cold Start Injection Pulse Performance. P062A - Fuel Pump Control Performance. P058C - Battery Monitor Module Temperature Monitoring Performance. P0607 - ECU Internal Performance. Injector performance faults for cylinders 2 - 4 map to DTC for incorrect cylinders. In addition the following software enhancement are included:Software corrects an issue with the wrong cylinder identification if an injector circuit performance fault is set in the PCM:If any of the series of injector control circuit faults are set, please refer to the bullet-pointed list below to determine which injector to address.For reference, the correct injector circuit performance faults are listed below:P02EE - Cylinder 1 Injector Circuit Performance. P02EF - Cylinder 2 Injector Circuit Performance. P02F0 - Cylinder 3 Injector Circuit Performance. P02F1 - Cylinder 4 Injector Circuit Performance. Customers may also experience the following condition:Audible noise from the Low Temperature Radiator (LTR) coolant pump, at low speeds. Abnormal noise from the radiator cooling fan. LTR runs too long after the engine is turned off.
21041202023-01-09. Service bulletin. FUEL SYSTEM, GASOLINE; POWER TRAIN; WHEELS. Transmission Case Oil Leak This bulletin involves tightening the lower transmission bolts to updated torque specifications to possibly eliminate a leak at the case split line of the transmission. Customers may notice (possibly transmission) fluid leaking on the ground from the left front of the vehicle.
18077222022-12-19. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING; AIR BAGS; PARKING BRAKE:ELECTRICAL; VEHICLE SPEED CONTROL; BACK OVER PREVENTION; SERVICE BRAKES, HYDRAULIC; FUEL SYSTEM, GASOLINE. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs: P1D83 - Implausible Engine Oil Temperature Signal Received. P2610 - PCM Internal Engine Off Timer Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit P0616 - Starter Control Circuit Lo. - Starter Control Circuit High. P0607 - ECU Internal Performance
1808420REVA2022-10-17. Service bulletin. BACK OVER PREVENTION; EXTERIOR LIGHTING; ELECTRICAL SYSTEM; SERVICE BRAKES; FUEL SYSTEM, GASOLINE; VEHICLE SPEED CONTROL; AIR BAGS. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P2610 - PCM Internal Engine Off Timer Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault). P0616 - Starter Control Circuit Low. P0617 - Starter Control Circuit High. P0607 - ECU Internal Performance. P3032 - Barometric Pressure Sensor Performance
18020212022-09-26. Service bulletin. FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM; VEHICLE SPEED CONTROL; BACK OVER PREVENTION; AIR BAGS; SERVICE BRAKES, HYDRAULIC; EXTERIOR LIGHTING. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P2610 - PCM Internal Engine Off Timer Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault). P0616 - Starter Control Circuit Low. P0617 - Starter Control Circuit High.P0607 - ECU Internal Performance.
25001192022-09-15. Service bulletin. FUEL SYSTEM, DIESEL; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Instrument Panel Cluster (IPC) Message about Diesel Particulate Filter (DPF) Regeneration
90044012022-08-22. Service bulletin. ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); ELECTRICAL SYSTEM; SERVICE BRAKES, HYDRAULIC; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE. DIFFERENTIAL, Rear Axle (KL 4WD w/DK2 = 1-SPEED RDM) The Differential, Rear Axle (aka RDM) design, pump design, Driveline Control Module (aka DLCM) hardware & software and pressure sensor have all changed in the past few years. The changes are not interchangeable and each had a separate implementation date. Please comprehend it to avoid repeat repairs. There are 2 sections each with 3 sub-sections: 1) For 2014/5 VINs with DK2 = 1-spd RDM 2) For 2016 and later VINs with DK2 = 1-spd RDM 1) For 2014/5 VINs with DK2 = 1-spd RDM 2014 - 2015 VINs were built with a 1-speed RDM used a 24 plate clutch design. New service RDMs 68550586A$ use a 20-plate design. 1.1) If replacing the RDM · 24 plate and 20-plate design RDMs are NOT interchangeable unless the Drive Line Control Module (DLCM) is also replaced. · 68550586A$ service RDMs have a 20 clutch plate design · Not all 20-plate RDMs have the new pump design. The new pump requires a new DLCM. · All new service RDMs are shipped with the new pump design. · If a new 68550586AA service RDMs is installed, then replace the DLCM with new DLCM 68540647AA - 1-spd designed for the 20-plate RDM. 1.2) If replacing the DLCM but not the RDM or pump assembly, then · If the RDM is the original 24 plate design then use 68540645AA - 1-spd, 24 plate DLCM AND replace the pump with 68551790AA · If the RDM is the new 20 plate design then use 68540647AA - 1-spd, 20 plate DLCM AND also replace the pump with 68551790AA new pump unless the RDM previously had a 68551790AA installed. 1.3) If replacing the pump assembly, then use 68551790AA (new pump) AND also replace the DLCM with the version that matches the correct version of the RDM (24 or 20 plate). · Use 68540645AA for the 24 plate RDM with a new pump. · Use 68540647AA for the 20 plate RDM with a new pump. 2) For 2016 and later VINs with DK2 = 1-spd RDM Early 2016 were built with 68090612AG 24 plate RDMs. Use Section 1 ?For 2014/5 VINs with DK2 = 1-spd RDM? to resolve. The balance of M
90044022022-08-22. Service bulletin. SERVICE BRAKES, HYDRAULIC; ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; BACK OVER PREVENTION. DIFFERENTIAL, Rear Axle (KL 4WD w/DK4 = 2-SPEED RDM) The Differential, Rear Axle (aka RDM) design, pump design, Driveline Control Module (aka DLCM) hardware & software and pressure sensor have all changed in the past few years. The chages are not interchangeable and each had a separate implementation date. Please comprehend it to avoid repeat repairs. There are 2 sections each with 3 sub-sections: 1) For 2014/5 VINs with DK2 = 1-spd RDM 2) For 2016 and later VINs with DK2 = 1-spd RDM 1) For 2014/5 VINs with DK4 = 2-spd RDM 2014 - 2015 VINs built with a 2-speed RDM used a 24 plate clutch design. Service RDMs (DK4: 68545100AA and DK4 + AWL: 68545101AA) have a 20-plate design. 1.1) If replacing the RDM · 24-plate and 20-plate design RDMs are NOT interchangeable unless the Drive Line Control Module (DLCM) is also replaced. · Both 68545100A$ and 68545101A$ service RDMs have a 20 clutch plate design · Not all 20 plate RDMs have the new pump design. The new pump requires a new DLCM. · All new service RDMs are shipped with the new pump design. · If a new 20 plate service RDM is installed, then replace the DLCM with new DLCM 68383660AE - 2-spd designed for the 20 plate RDM. 1.2) If replacing the DLCM but not the RDM or pump assembly, then · If the RDM is the original 24 plate design then use 68540646AA - 2-spd, 24 plate DLCM AND also replace the pump with 68551790AA new pump. · If the RDM is the new 20 plate design then use 68383660AE - 2-spd, 20 plate DLCM AND also replace the pump with 68551790AA new pump unless the RDM previously had a 68551790AA installed. 1.3) If replacing the pump assembly, then use 68551790AA (new pump) AND also replace the DLCM with the version that matches the correct version of the RDM (24 or 20 plate). · Use 68540646AA for the 24-plate RDM with a new pump. · Use 68383660AE for the 20-plate RDM with a new pump. 2) Early 2016 were built with 24 plate RDMs. These include p/n?s 68090615AJ (2spd std), and 52123642AJ (2spd locker). Use Secti
18-047-202020-06-22. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT; ENGINE; FUEL SYSTEM, GASOLINE; SERVICE BRAKES, HYDRAULIC. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs:P2610 - PCM Internal Engine Off Timer Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault). P0616 - Starter Control Circuit Low. P0617 - Starter Control Circuit High. P0607 - ECU Internal Performance. P3032 - Barometric Pressure Sensor Performance
18-039-202020-05-26. Service bulletin. FUEL SYSTEM, GASOLINE. Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
90042442020-05-26. Service bulletin. POWER TRAIN; FUEL SYSTEM, GASOLINE. COOLER, Transmission Oil Work procedure to address fluid leak issue with the transmission oil cooler on the MP (Part # 68249191A$), KL (Part # 68399021A$) and RU (Part # 68217322A$) needs to be followed. Service Instructions for the Condition of a TOC fluid leak: 1) Mark the leakage area if visible to assist in diagnosis and determination of the area where the leak has occurred. 2) If fluid leak was caused by damage or leakage at the transmission oil cooler: - Replace transmission oil cooler - Test drive and verify no additional fluid leaks 3) If fluid leak was caused by leak at quick connect fittings: - Replace transmission oil cooler lines - Test drive and verify no additional fluid leaks
18-089-192019-12-16. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE. wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
25-001-192019-12-16. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; FUEL SYSTEM, DIESEL; ELECTRICAL SYSTEM. Instrument Panel Cluster (IPC) Message about Diesel Particulate Filter (DPF) Regeneration
90041502019-12-02. Service bulletin. FUEL SYSTEM, GASOLINE; POWER TRAIN. SEAL, Input If looking to replace stubshaft due to ATX fluid leaking, do not replace PTU seals. None of the seals from the PTU side will need to be replaced whenever the ATX stubshaft is replaced, even though V-seal (68408748A$) is in direct contact with the stubshaft, it will not avoid grease/oil leakage from transmission side. PTU V-seals are intended to act as a dust cover for stubshaft - PTU input shaft spline interface. PTU Input shaft seal (68408749A$) is intended to hold PTU oil and debris ingress; it should be replaced only if the fluid leakage is confirmed to be PTU oil and not ATX trans. fluid.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.