WenmarOpen by Wenmar Pro

Service bulletins for the 2019 Jeep Cherokee

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

407 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Lighting are shown. Show all

Bulletins, newest first
23004242024-03-18. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS. Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
08112232023-05-30. Service bulletin. EXTERIOR LIGHTING; EXTERIOR LIGHTING:TAIL LIGHTS. Rear Tail Lamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior tail lamp assemblies are fogged with a light layer of condensation on the inside of the lenses. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off, and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). This bulletin is to communicate the procedure for rear tail lamp condensation clearing.
09-003-232023-02-13. Service bulletin. SERVICE BRAKES; EXTERIOR LIGHTING. 2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: Oil pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.
18-161-222023-01-17. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; BACK OVER PREVENTION; VEHICLE SPEED CONTROL; EXTERIOR LIGHTING. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or moreof the following DTCs have been set: P02EE - Cylinder 1 Injector Circuit Performance. P02EF - Cylinder 2 Injector Circuit Performance. P02F0 - Cylinder 3 Injector Circuit Performance. P02F1 - Cylinder 4 Injector Circuit Performance. P2C90 - Crankcase Ventilation System - Hose "A" Disconnected. P1D73 - AGS performance fault. P04FC - Crankcase Ventilation System Performance. P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation(Enlarged Europe and Middle East/Africa) only equipped with Gas ParticulateFilter (GPF))(DTC will set when driving above 72 kph (45 mph). P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P050B - Cold Start Ignition Timing Performance. P258B - Electric Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P2B95 - Cold Start Injection Pulse Performance. P062A - Fuel Pump Control Performance. P058C - Battery Monitor Module Temperature Monitoring Performance. P0607 - ECU Internal Performance. Injector performance faults for cylinders 2 - 4 map to DTC for incorrect cylinders. In addition the following software enhancement are included: AGS stuck condition (The customer won't see an issue, but this calibrationallows AGS performance fault - P1D73, to work correctly). Software corrects an issue with the wrong cylinder identification if an injectorcircuit performance fault is set in the PCM: If any of the series of injector control circuit faults are set, please refer tothe bullet-pointed list below to determine which injector to address.
S22180000232023-01-17. Service bulletin. EXTERIOR LIGHTING; BACK OVER PREVENTION. Malfunction Indicator Lamp (MIL) Illuminated. Diagnostic Trouble Code (DTC) U02A3 ? Lost Communication ith Particulate Matter (PM) Sensor, Set After PM Sensor Replacement.
S2008000131 Rev.2023-01-17. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING. U11E9 Lost Communication with AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated
18052202023-01-09. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; BACK OVER PREVENTION; ENGINE AND ENGINE COOLING; EXTERIOR LIGHTING; VEHICLE SPEED CONTROL. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set:P04FC - Crankcase Ventilation System Performance. P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation(EMEA only equipped with Gas Particulate Filter (GPF))(DTC will set when driving above 72 kph (45 mph). P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P050B - Cold Start Ignition Timing Performance. P258B - Electric Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P2B95 - Cold Start Injection Pulse Performance. P062A - Fuel Pump Control Performance. P058C - Battery Monitor Module Temperature Monitoring Performance. P0607 - ECU Internal Performance. Injector performance faults for cylinders 2 - 4 map to DTC for incorrect cylinders. In addition the following software enhancement are included:Software corrects an issue with the wrong cylinder identification if an injector circuit performance fault is set in the PCM:If any of the series of injector control circuit faults are set, please refer to the bullet-pointed list below to determine which injector to address.For reference, the correct injector circuit performance faults are listed below:P02EE - Cylinder 1 Injector Circuit Performance. P02EF - Cylinder 2 Injector Circuit Performance. P02F0 - Cylinder 3 Injector Circuit Performance. P02F1 - Cylinder 4 Injector Circuit Performance. Customers may also experience the following condition:Audible noise from the Low Temperature Radiator (LTR) coolant pump, at low speeds. Abnormal noise from the radiator cooling fan. LTR runs too long after the engine is turned off.
S20080001012023-01-09. Service bulletin. AIR BAGS; EXTERIOR LIGHTING; ELECTRICAL SYSTEM:ADAS:BLINDSPOT:SENSORS. Blind Spot Indicator Light Remains On In High Ambient Temperatures
18077222022-12-19. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING; AIR BAGS; PARKING BRAKE:ELECTRICAL; VEHICLE SPEED CONTROL; BACK OVER PREVENTION; SERVICE BRAKES, HYDRAULIC; FUEL SYSTEM, GASOLINE. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs: P1D83 - Implausible Engine Oil Temperature Signal Received. P2610 - PCM Internal Engine Off Timer Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit P0616 - Starter Control Circuit Lo. - Starter Control Circuit High. P0607 - ECU Internal Performance
18063202022-10-17. Service bulletin. AIR BAGS; BACK OVER PREVENTION; ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P20EE-00 - SCR NOx Catalyst Efficiency Below Threshold Bank 1 Catalyst 1. P24B2-00 - Particulate Matter Sensor Circuit Intermittent. Customers may also describe the following condition:Engine Start/Stop inoperative. Remote start inoperative(South Korea vehicles only). Incorrect vehicle speed reported by the cluster when the driver changes the speed units. Undesirable pedal response in 4-LO mode. Selective Catalytic Reduction (SCR) system fault codes logged at higher vehicle speeds. Alternator load protection at idle. Check Engine Lamp or low battery indicator
1808420REVA2022-10-17. Service bulletin. BACK OVER PREVENTION; EXTERIOR LIGHTING; ELECTRICAL SYSTEM; SERVICE BRAKES; FUEL SYSTEM, GASOLINE; VEHICLE SPEED CONTROL; AIR BAGS. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P2610 - PCM Internal Engine Off Timer Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault). P0616 - Starter Control Circuit Low. P0617 - Starter Control Circuit High. P0607 - ECU Internal Performance. P3032 - Barometric Pressure Sensor Performance
S2008000131RevB2022-10-17. Service bulletin. EXTERIOR LIGHTING. U11E9 Lost Communication With AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated
23024222022-09-26. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS. Headlamp Condensation Clearing Procedure This bulletin is to communicate the procedure for headlamp condensation clearing.
18020212022-09-26. Service bulletin. FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM; VEHICLE SPEED CONTROL; BACK OVER PREVENTION; AIR BAGS; SERVICE BRAKES, HYDRAULIC; EXTERIOR LIGHTING. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P2610 - PCM Internal Engine Off Timer Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault). P0616 - Starter Control Circuit Low. P0617 - Starter Control Circuit High.P0607 - ECU Internal Performance.
S2008000131RevC2022-09-15. Service bulletin. EXTERIOR LIGHTING. U11E9 Lost Communication With AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated
S21080000622022-08-22. Service bulletin. EXTERIOR LIGHTING. U11E9 Lost Communication With AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated
08-037-222022-06-27. Service bulletin. EQUIPMENT; EXTERIOR LIGHTING:TAIL LIGHTS. Rear Tail Lamp Condensation Clearing Procedure This bulletin is to communicate the procedure for rear tail lamp condensation clearing. Some customers may report that on occasion, vehicle exterior tail lamp assemblies are fogged with a light layer of condensation on the inside of the lenses. This may be reported after the lamps have been turned on and brought up to operatingtemperature, turned off, and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e., a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into avapor. Turning the tail lamps on will usually accelerate this process.Clear Tail Lamp AssemblyTail Lamp Assembly with CondensationImages are not specific to vehicle, and only used for showing the tail lamps either clearFig. 1or having a condensation build up within the tail lamp assemblyFig. 2per the procedure.
08-060-212021-05-24. Service bulletin. EXTERIOR LIGHTING:TAIL LIGHTS. Rear Tail Lamp Condensation Clearing Procedure This bulletin is to communicate that a new procedure for rear tail lamp condensation clearing that is now available in the service information.
18-023-202020-05-26. Service bulletin. EXTERIOR LIGHTING; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0780 - Gear Shift Malfunction. P050B - Cold Start Ignition Timing Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. Customers may also comment on one or more of the following:Extended engine crank times or possibly a no start condition(South Korea with Sales Code EDD only). The engine fails to restart while in Engine Stop/Start (ESS) mode. This is usually accompanied withDTC P06EF.
S18080001752020-05-26. Service bulletin. EXTERIOR LIGHTING. LED Front Fog Lamps Flicker Or Intermittently Light, Are Dim Or Inoperative. A U11E9, or B16FB-15 may be set
S18080001752020-05-18. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM. LED Front Fog Lamps Flicker Or Intermittently Light, Are Dim Or Inoperative. A U11E9, or B16FB-15 may be set
S18080001752020-04-27. Service bulletin. ELECTRICAL SYSTEM; VISIBILITY; EXTERIOR LIGHTING. LED Front Fog Lamps Flicker Or Intermittently Light, Are Dim Or Inoperative. A U11E9, or B16FB-15 may be set

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.