WenmarOpen by Wenmar Pro

Service bulletins for the 2014 GMC Yukon

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1641 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
16NA3382018-05-07. Service bulletin. POWER TRAIN. This Bulletin provides guidelines for Dealers to determine whether or not they need to contact the PQC for an engine, transmission or transfer case assembly replacement and information explaining the PQC process, Global Warranty Management Transaction submission, vehicle repair record retention and proper handling of assembly returns.
PI09382018-04-23. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. This preliminary information bulletin provides information on powertrain and various electronic/electrical control issues.
09-06-04-026G2018-04-23. Service bulletin. ENGINE; POWER TRAIN. This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2® or global diagnostic system 2 (GDS 2)
PIP5168F2018-02-21. Service bulletin. POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published “Engine Cranks But Does Not Run” diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
06-00-89-031C2017-12-22. Service bulletin. POWER TRAIN; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This informational bulletin provides information to dealership personnel on proper engine and automatic transmission/transaxle identification.
030729004I2017-12-22. Service bulletin. POWER TRAIN. This informational bulletin was created for the Manual Transmission Operating Characteristics. The different noises caused by driver habit, weather conditions , and normal manual transmission noises.
PIP4112P2017-12-22. Service bulletin. ENGINE; POWER TRAIN. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PIP4653E2017-12-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicle that have a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0601, P0603, P0604, P062F or P1621 stored in the Transmission Control Module. Technician will need to ensure that the Diagnostic Trouble Codes are set in the Transmission Control Module. If the Diagnostic Trouble Codes are only set in the Transmission Control Module reprogram the Transmission Control Module.
PIT5202D2017-12-14. Service bulletin. ENGINE; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission, now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.
16-NA-3382017-08-31. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
PIT5202C2017-08-15. Service bulletin. ENGINE; POWER TRAIN; SERVICE BRAKES, HYDRAULIC:POWER ASSIST. This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission. Starting with the 2013 model year, Full Size Trucks and Utilities now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.
PIT54422017-08-15. Service bulletin. POWER TRAIN; EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center.
PI13282017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This preliminary bulletin provides a procedure to inspect and repair the parking pawl spring in the transmission if the customer states that theres a grind or rattle noise during a left turn or bump.
PI1344A2017-08-15. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY. This preliminary bulletin provides a procedure to remove and inspect the clutch select solenoid valve for damage, located in the valve body to correct the customers concern of reduced acceleration at low speeds and trans slip at lauch.
PI13602017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This preliminary bulletin provides a procedure to perform a transmission inspection and adjustment before having to replace the parking pawl actuator if the inspection found no problem.
PIP5382H2017-08-15. Service bulletin. WHEELS:LUGS/NUTS/BOLTS/STUDS; POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. This Preliminary Information communication advises the technician that generation 5 engines with Regular Production Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner’s Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before doing any repairs to the vehicle.
PI0020D2017-08-15. Service bulletin. POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT. This preliminary informational bulletin provides technicians with information on the normal condition of white, milky or cloudy appearance of front differential fluid.
PI1360C2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:PARK/NEUTRAL START INTERLOCK SWITCH. This preliminary informational bulletin provides diagnosis and repair information to correct a customer concern of alleged no park, vehicle rolls in park or park will not hold.
PI1360B2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:PARK/NEUTRAL START INTERLOCK SWITCH. This preliminary informational bulletin provides diagnosis and repair information to correct a customer concern of alleged no park, vehicle rolls in park or park will not hold.
06-00-89-026L2017-08-15. Service bulletin. SERVICE BRAKES; EQUIPMENT:ELECTRICAL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER; POWER TRAIN:AXLE ASSEMBLY; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND.
PIP3119N2017-08-15. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; POWER TRAIN. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
PIP4765A2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have Service Engine Soon Malfunction Indicator Lamp on and a constant engine misfire. If Service Information diagnosis isolates no compression on the misfiring cylinder(s) with 100% leakage into the crankcase, perform the following steps as necessary before disassembling the engine. Technician will use a lighted bore scope if available to inspect the top of the related piston(s) through the spark plug hole to determine if any of the pistons are melted. If damaged piston(s) are found inspect for aftermarket parts. Also use the latest version of 09-06-04-026 to verify if there are aftermarket calibrations in the Engine Control Module. Take photos and document accordingly if anything is found.
PIT5206A2017-08-15. Service bulletin. SERVICE BRAKES, AIR:CONTROLS:FOOT CONTROL/VALVE; ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages " Brake Pedal Override Feature ", transmission busy or frequent shifting up or down. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor.
PIT5202A2017-08-15. Service bulletin. POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission. Starting with the 2013 model year, Full Size Trucks and Utilities now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.
PIT5202B2017-08-15. Service bulletin. SERVICE BRAKES; POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission. Starting with the 2013 model year, Full Size Trucks and Utilities now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.