Service bulletins for the 2016 GMC Yukon XL
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1454 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| 15-00-89-004 | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This informational bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered seepage. |
|---|---|
| 15-00-89-003 | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This informational bulletin provides information on dealer reimbursement procedures for Customer Assistance Center (CAC) Tier 1 and Tier 2 empowerment tools: diagnostic fee, short term rental, and up-front towing (U.S. only). |
| PIT5389C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system. |
| PIC4935F | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. |
| PIP4723B | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update. |
| PIC5959C | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module. |
| PIC4801H | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance. |
| PIC3278G | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; STEERING. This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern. |
| PIC5588C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System. |
| PIP5029H | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years. |
| PIP5338A | 2017-08-15. Service bulletin. EQUIPMENT. This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number. |
| PIP4902J | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question. |
| PIC6086C | 2017-08-15. Service bulletin. VISIBILITY:WINDSHIELD; VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR. This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced. |
| PIT5380B | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; SEATS:FRONT ASSEMBLY:RECLINER. This Preliminary Information communication provides information to the technician about vehicle that may have a front driver's or passenger's seat back may lean or be turned outward. Technician will need to remove the seat bottom trim cover and reinstall it completely and squarely to the cushion to correct the concern. |
| GCUS-3-848 | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL. 44180 02 - Customer Satisfaction. Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Dealers are to replace all applicable keys and lock cylinders with new key configurations. |
| PIT5543 | 2017-08-15. Service bulletin. SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER; ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. This Preliminary Information communication provides information to the technician about vehicles that have a dead battery after sitting for more than 20 days. Technician will need to change Rear Heated Seat Control Module power circuit 5140 from a hot-at-all-times fuse to a hot-in-run/crank fuse. |
| PIT5405C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; STEERING:ELECTRIC POWER ASSIST SYSTEM; STEERING:HYDRAULIC POWER ASSIST SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a reduced or loss of power steering assist, steering wheel jerks or kicks back when turning, Service Stabilitrak message with warning chime, engine stall, Instrument Panel Cluster going blank or inoperative, radio/Integrated Center Stack going blank, Heater-Vent-Air Conditioning going blank, hood ajar message and/or dome lamps flash when shifting into reverse, alarm sounds when locking doors or door locks cycling, and or wipers continue to run for a short time after turning off and then stop/park in the incorrect location. Technician may find Diagnostic Trouble Codes U0073, U0078, U0029, U0028, U0415, U0140, U0126, U0121, U0101, U0100, C0544, C0710, U1510, B127B, B2605, B3600, C0800, U0428, U0452, U0131, and P0513 set in the vehicle. Check the body control module ground at the G218 location. The front dash insulator mat may be trapped between the ground eyelet and the body stud. Remove the round nut and eyelet and cut the front dash insulator mat away from the ground stud so it no longer interferes with the ground stud and reinstall the eyelet and ground nut. Technician will also inspect the starter solenoid battery cable for shorting out on the starter heat shield. Technician will need to voltage drop the battery cables. The battery should be tested using the GR8. X183 or X133 should be inspected for any broken/loose/backed out terminals. |
| PIT5509A | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System" message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector. |
| PIT5542 | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; SEATS. This Preliminary Information communication provides information to the technician about vehicles that have an excessive lateral driver or passenger seat movement and/or a clunk/click/pop type feeling or noise. Technician will need to install a front seat lateral retainer. Technician will need to remove plastic material from the top side of the guide end of the lateral retainer to enable installation. |
| PIT5295C | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician on the step to diagnose and repair vehicles with a CD or DVD player that will not take a disc. Technician will gain access to the player and inspect the player to be mounted on the locating pins. If the player is not mounted on the location pins reinstall the player. |
| PIT5448C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time. |
| PIT5233C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:IGNITION:SWITCH; STEERING; ELECTRICAL SYSTEM:IGNITION. This Preliminary Information communication provides information to the technician about vehicles that may have hard or unable to rotate ignition key concern. When the concern is present the steering wheel will need to be rotated in either direction to alleviate the pressure between the steering column lock pin and lock plate. Please communicate to the customer this condition is a normal operating characteristic of their vehicle. |
| PIT4733K | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system. |
| PIP3119N | 2017-08-15. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; POWER TRAIN. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. |
| PIC5759B | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.