WenmarOpen by Wenmar Pro

Service bulletins for the 2015 GMC Yukon XL

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

2156 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
PIC5491G2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
PIT54422017-08-15. Service bulletin. POWER TRAIN; EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center.
PIP5274B2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician to call General Motors Technical Assistance Center if the customer has a malfunction indicator lamp on and there is a diagnostic trouble code P16F3 set in the transmission control module.
PIT54262017-08-15. Service bulletin. EQUIPMENT. This Preliminary Information communication provides information to the technician for a water leak in in the second row seating area. Inspect the C-pillar area of the affected side of the vehicle for water intrusion or water marks on the seat belt retractor. If water evidence is found on the seat belt webbing or the retractor the seat belt/ retractor must be replaced after the water leak has been corrected and verified. There are 3 areas of seam sealer that will need to be addressed. After gaining access to the C-pillar and rear quarter panel area inspect for voids or missing seam sealer and apply a clear flow able seam sealer where needed.
PIT5245B2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that the blower motor may be noisy or vibrate when running. This concern will only occur when the temperatures is below 32 degrees Fahrenheit and if the blower motor is removed while still cold, ice may be found on the blower motor cage. This concern could be caused by water leaking or snow ingestion into the Heater-Vent-Air Conditioning case. Technician is to perform normal water testing diagnostics while the Heater-Vent-Air Conditioning is running, looking for water leaking past the plenum cover. If water is leaking past the cover remove the cover and install a 12x12 snow resistant screen to the fresh air intake. Reseal and install the plenum cover cap using Kent air dry sealer or equivalent.
PIT54212017-08-15. Service bulletin. STRUCTURE. This Preliminary Information communication provides information to the technician that there was a temporary change to the frame coating on some vehicles. These vehicles will be painted with environmental coating rather than the normal frame wax. The environmental coated frames meet or exceed General Motors specifications for corrosion and no repair should be made.
PIT5278C2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician about vehicles with erratic or hesitation when opening and closing the power lift gate. There may be a diagnostic trouble code B153A set in the power lift gate module. This concern could occur if the left lift gate actuator is internally coming apart. The actuator will need to be replaced however care must be taken when removing the actuator from the vehicle. If the internal portion of the actuator had completely separated the end of the actuator could become a projectile when removed. Obtain a number 8 self-tapping screw that measures 1 ½ inches long. Fully open the lift gate and install the screw anywhere in a 30 millimeter space from the bottom of the smooth tube to secure the tubes. Continue with the lift gate actuator by following the lift gat power assist actuator procedure in service information.
PIP52982017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician for a Service Engine Soon light with a Diagnostic Trouble code P0300 set. There may be a rough running engine associated with this concern. If service information diagnostics have been completed and there is still no trouble found, the technician is to inspect for a possible terminal tension concern on the ignition coil power feed for the cause of the rough running engine and or the P0300. For the Service Engine Soon light or traction control lamp concern check the X2 connector of the under hood fuse block for poor pin retention.
PIT5365C2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician on how the radio display gets the air ambient temperature. On 1500 series trucks and all sport utility vehicle with regular production option code IO3 radio the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio. On 1500 series trucks and all sport utility vehicle with regular production option code IO4, IO5, or IO6 the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface. On 2500/3500 series trucks production option code IO3 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio. On 2500/3500 series trucks production option code IO4, IO5, or IO6 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface.
PIT54182017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician for vehicles with a black bar while on the Bluetooth audio streaming screen. This concern is a normal operating characteristic of the vehicle and no repairs should be made.
PIT5379A2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician about vehicles that may have a content theft alarm sounding for no apparent reason. Technician may use all published Service Information diagnostics and has not found the cause of the unwanted content theft alarm sounding. Technician should use Global Diagnostic System 2 to review the Body Control Module parameters for "Content Theft Deterrent Trigger History". This is a list of triggers that can cause a content theft alarm sounding. Driver door Passenger door, Left rear door, Right rear door, Rear closure, Tonneau Cover, Hood, Ignition Voltage, Intrusion, Inclination, Telematics enhanced service alarm, Battery reconnect detected, Unauthorized Pulse Width Modulated change, Security Indicates Tamper, and Glass Breakage. If the trigger is an Intrusion inspect for items hanging from the rear view mirror, solar powered dancing characters. When the trigger is a Glass breakage inspect the two rear quarter-panel windows and also in the liftgate glass. The quarter panel windows are attached to the body harness with a connector that looks similar to a 9 volt battery connector inspect them to be fully seated in on the glass. When the trigger is Ignition Voltage/Battery reconnect detected during a cold ambient temperature remote vehicle start event technician should call GM General Motors Technical Assistance Center for further assistance.
PIT5076E2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.
PIC60952017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. There are pictures of all the individual modules for identification purposes.
PIP52932017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician when the customer complaint on a noise from the transmission when the engine starts. The noise may be a clunk with a bump sensation. This condition may be caused by turning the engine off and then quickly restarting it. The transmission control module doesn?t have adequate time to power down and the 1-2-7-8-R along with the 1-2-3-4-5-R clutches will apply at maximum line pressure causing this concern. This is considered normal operation if the transmission control module is not allowed to power down before restarting the engine. The transmission control module needs the transmission to be placed in park the ignition turned off and the door opened and closed. After closing the door the transmission control module requires 2 minutes before the engine should be restarted. If the concern is present and duplicated after following the power down procedure the General Motors Technical Assistance Center for further direction.
PIT54092017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician on how to tell vehicles built with text messaging and vehicles that are not. The text messaging feature was not available at the start of production on the sport utility vehicle or heavy duty truck. The option was added mid-cycle production. These utility and heavy duty pickup models must have regular production option code AVF to have the text messaging feature. There is no upgrade available to add text messaging to a vehicle that was built without it.
PIP52882017-08-15. Service bulletin. ENGINE. This Preliminary Information communication advises the technician to check for an engine build code of K and the dates between 15005 and 15117, the customer concern is an engine oil leak at the oil filter location of the oil pan. A loose oil filter adapter is found to be the cause of the concern, tighten it to 55 newton meters or 40 foot pounds. It is also advised to clean any residual oil from the oil pan area.
PIT54082017-08-15. Service bulletin. SEATS. This Preliminary Information communication advises the technician that some vehicles the haptic seat motors can be felt in the seat. Technician will access both haptic seat motors and rotate the motors flat, and then reinstall them back into the seat cushion. This will help improve the comfort of the seat cushion.
PIT5279B2017-08-15. Service bulletin. ELECTRICAL SYSTEM; SEATS. This Preliminary Information communication provides information to the technician for vehicles that exhibit a driver?s power memory seat and power adjustable pedals inoperative. Look for poor terminal tension at the left instrument panel fuse block connector X1 terminals 27 and 28. If poor retention is found in these terminals replace them with terminated lead part number 19301761.
PIT54072017-08-15. Service bulletin. LATCHES/LOCKS/LINKAGES:HATCHBACK/LIFTGATE:LOCK. This Preliminary Information communication provides information to the technician of a concern on vehicles where the power lift gate binds or makes a popping noise when operated the gate also may not stay open. In most cases no diagnostic trouble codes will be set. The concern is most likely caused by the passenger side strut binding between the inner and outer tubes. Replace the passenger side strut and only if the concern is still present replace the driver side actuator.
PIT5231C2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about vehicles that may have a blank radio display. Technician may find a Diagnostic Trouble Code U150F stored in the Radio / Heater-Vent-Air Conditioning controls. Technician will verify if the correct display is installed. If the Diagnostic Trouble Code is current inspect the circuit form end to end.
PIT5377A2017-08-15. Service bulletin. SERVICE BRAKES, AIR:DISC:PADS. This Preliminary Information communication provides information to the technician on the steps needed to diagnose and repair vehicles that may have uneven brake pad wear. Technician will need to contact General Motors Technical Assistance Center for further assistance.
PIT54052017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician for a reduced power message, steering assist, engine stall or the instrument panel, radio, and or Heater-Vent-Air Conditioning go blank with multiple diagnostic trouble codes. If any of the following diagnostic trouble codes U0073, U0078, U0029, U0028, U0415, U0140, U0126, U0121, U0101, U0100, C0544, U1510, U0073, B127B, B2605, B3600,C0800, U0428, and U0452 set in the vehicle. Check the body control module ground at the G218 location. The front dash insulator mat may be trapped between the ground eyelet and the body stud. Remove the round nut and eyelet and cut the front dash insulator mat away from the ground stud so it no longer interferes with the ground stud and reinstall the eyelet and ground nut.
PIT54042017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; SUSPENSION. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a buffeting vibration and/or drone type noise, exhaust tone change, and/or body pressure booming. The concern may be most noticeable while the engine is operating in 4-cylinder Active Fuel Management mode in the 1,100-1,400 RPM range. If the noise is excessive it may excite the roof sheet metal and compound the issue, if this concern is found refer to the latest version of PIT5318. If the concern is qualified to be present during V4 mode operation, but is deemed to be normal by comparing to a like vehicle, then no further repairs should be made, as this is a normal characteristic. If the concern is qualified to be present during V4 mode operation, but is deemed excessive by comparing to a like vehicle then continue with the direction in the Preliminary Information. Vehicles equipped with the 6.2 liter engine and noise cancellation, the noise cancellation may not be working or working incorrectly this can be the cause of the issue. Technician should inspect for aftermarket audio components, objects blocking the microphones or speakers, Diagnostic Trouble Codes B0560, B1277, B127C, or B127D. By the technician pulling the fuse for the amplifier the noise cancellation will be disabled if the noise improves there may be an issue with the noise cancellation system. Technician should inspect the exhaust system also. Exhaust should be checked when it is hot and cold while the vehicle is in neutral, forward and reverse gear. Inspect the exhaust system for loose and/or missing fasteners, heat shields damaged, joints and/or couplings not properly seated, bracket and/or insulator mounting concerns, inadequate clearance to body and/or chassis components, improper alignment, disconnected and/or missing insulators, cracked, dry-rotted, and/or oil-soaked insulators, stretched, twisted, broken, torn, and/or collapsed insulators, and bent, twist
PIT54032017-08-15. Service bulletin. SUSPENSION. This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.
PIT54012017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician for vehicles with the radio inoperative. The technician may find no communication with the radio and a diagnostic trouble code U0184 set in other modules. Technician is to call General Motors Technical Assistance Center for direction before attempting to diagnose or repair this concern.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.