WenmarOpen by Wenmar Pro

Service bulletins for the 2015 GMC Yukon XL

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

2156 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
PIT52942017-12-22. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a tinny, rattle or buzz noise from the rear of the vehicle. Technician will need to replace the broken stud by installing a M6 rivet stud using the latest version of bulletin 10-08-45-001.
PIP5337J2017-12-14. Service bulletin. POWER TRAIN; ENGINE. This Preliminary Information communication provides information to the technician on the step to diagnose and repair the vehicles that may have a shake or shudder during light throttle acceleration, between 30 and 65 miles per hour steady state driving. Also shudder feeling that may be described as driving over rumble strips or rough pavement. Technician will need to run the vehicle in three different operational modes. The three modes are Normal, torque converter clutch open, and torque converter clutch closed. Technician will need to press and hold the tow-haul mode button for five seconds to disable grade braking to prevent downshifts during test. Technician will need to duplicate the concern in Normal mode. If the concern is gone in torque converter clutch open and closed then the torque converter should be replaced. If the concern is not present in normal mode, torque converter clutch open, and torque converter clutch closed the concern is not with the shudder. Technician should use of the PICO scope and Noise, Vibration and Harshness software can be used to confirm torque converter clutch shudder, Engine, Tire or Driveline component related conditions. Flush the cooler lines and cooler using DT-45096 transmission oil cooling system flush and flow test tool when the torque converter is replace.
PIE0350B2017-08-31. Service bulletin. ENGINE AND ENGINE COOLING. This engineering informational bulletin is requesting information from the field on vehicles that have a concern on Bang or Loud Noise with No Forward (Drive) or Reverse Ranges
16-NA-0272017-08-31. Service bulletin. ENGINE. This technical bulletin provides a procedure to replace 4-5-6 clutch hub to correct a condition of No Fourth, Fifth and Sixth Gears and/or Malfunction indicator Lamp Illuminated with DTC P0796
PIP5395B2017-08-31. Service bulletin. ENGINE. This Preliminary Information communication advises the technician on the steps to diagnose the concern and the steps to repair the concern. Customer hears a rattle or ticking noise that is louder inside the vehicle than outside. A-This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.
PIP5232B2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIP5258A2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Code P0011. If the technician has followed all published Service Information diagnosis and has not come to a conclusion, technician should check the oil pressure at the oil pressure sender. Then the number two cam bearing should be inspected.
PIP5130F2017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.
PIP53572017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about vehicles with engine oil consumption. If published Service Information for oil consumption with no fix. Remove the vacuum line from the back of the vacuum pump and inspect for oil. If oil is found then reference the latest version of PIT5361.
PIT4943D2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
PIP5179B2017-08-15. Service bulletin. ENGINE; EQUIPMENT:MECHANICAL; FUEL SYSTEM, OTHER:FUEL INJECTION SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines.
PIP5199A2017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about vehicles with a crankshaft balancer appears to be out of balance or wobbling while watching it with the engine running. Technician will need to check crankshaft balancer run out. If the balancer run out is greater than 0.25mm the crankshaft balancer will need to be replaced.
PIT5202C2017-08-15. Service bulletin. ENGINE; POWER TRAIN; SERVICE BRAKES, HYDRAULIC:POWER ASSIST. This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission. Starting with the 2013 model year, Full Size Trucks and Utilities now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.
PIP5163B2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FUEL SYSTEM, GASOLINE; ENGINE. This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP54422017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have an exhaust leak, noisy exhaust, or noise mid-vehicle. Technician will need to check for an unseated pipe to pipe mid-joint connection. Technician will need to install new exhaust band.
PIP5382F2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE. This Preliminary Information communication advises the technician that generation 5 engines with Regular Production Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner?s Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before you contacting General Motors Product Quality Center.
PIP52522017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that the engine may run hot with the snow plow installed. Do not exceed 64?kilometers per hour / 40?miles per hour with a snow plow mounted to the vehicle even if equipped with VYU. The vehicle could overheat and be damaged.
PIP5211B2017-08-15. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair vehicles with a rough idle and/or vibration at idle in Drive. This condition will not be present in Park, or Neutral. This concern may be caused by ground out within the one or both engine mounts. Technician will use CH-51450-A (Pico Oscilloscope) to measure the vibration disturbance. If the vibration concern is E1.5 in the horizontal / lateral direction with Pico sensor mounted in seat track as indicated ? continue with steps to reduce the amplitude of the vibration by adding spacers in key locations to reduce ground out within the engine mounts. The 6.2L engine has a characteristic E1 which can be felt, and may be described as a lopey idle. Do not confuse 6.2L E1 characteristic (not caused by mount ground-out), with E1.5 normal idle characteristics being transmitted into the truck via ground-out thru the engine mounts. If measuring high at the seat track 12 mg or greater; replacement of the engine mounts should help reduce the amplitude of the vibration. If the disturbance measures at the seat track as E 1.5 lateral in the range of approximately 2.5 - 8 mg using a tri-axis sensor. Then place tri-axis Pico sensor on the inboard seat track forward-most location to record measurement of the rough idle vibration concern. With the Heater-Vent-Air Conditioning on perform several short heavy launch events from stop to stop to bring the temperatures back up while attempting to re-create the rough idle vibration in Drive with Pico sensor placed on inboard seat track; while the vibration is active ? Record Pico reading. This method seems to provide better results than extended test drives. If the Pico reading for E1.5, with vibration active, at specified seat track location measures close to 2mg or less use Service Information to diagnose rough idle / vibration. If the Pico reading for E1.5, with vibration active, at the inboard forward seat track
PIP5029F2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
PIT53502017-08-15. Service bulletin. ENGINE; ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician that there have been some reports that the current engine hours are not correct and display 0.0. Technician will need to program the Instrument Panel Cluster using Service Programming System.
PIT5448A2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM.
PIP5230B2017-08-15. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication advises the technician before replacing the crankshaft to review the following. Dealer should complete the Service Information diagnostics and the Cost Comparison Worksheet for Assembly Repair vs. Replacement. Technician will use the latest version of 09-06-04-026G to verify the Engine Control Module calibration is not an aftermarket calibration. If the customer prefers to keep the original numbers matching engine please call General Motors Technical Assistance Center for repair direction.
PIP5179A2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines.
PIP5272A2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that may have low oil pressure after an oil change. Technician will inspect the oil filter part number PF63E. Part number PF48 oil filter will fit but will cause a low oil pressure concern.
PIT54482017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that stop running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.