WenmarOpen by Wenmar Pro

Service bulletins for the 2000 GMC Suburban

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

261 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
24-NA-1412024-08-15. Service bulletin. POWER TRAIN. GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
PI1394B2024-02-02. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. This PI bulletin advises the technician on the proper way to install the pistons in an engine.
23-NA-1532023-09-26. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
PIP5640A2022-10-17. Service bulletin. POWER TRAIN. This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
22-NA-1812022-09-19. Service bulletin. POWER TRAIN. This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
PIP53462017-08-15. Service bulletin. EQUIPMENT; POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES; POWER TRAIN. This Preliminary Information communication provides information to the technician about cooler line fittings that come with the 4T65E General Motors remanufactured transmission may not be the same as Original equipment manufacturer quick connect verses inverted flare. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIP3259J2017-08-15. Service bulletin. POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that may have a planetary gear whine noise in first and second gear. Technician should compare the noise to a like vehicle. Technician will need to check the build date of the transmission, if it was built after 09/01/2003 and it is determined that a vehicle has an abnormal amount of noise, perform the rear unit end play check. Technician will replace the output planetary gear set if end play is out of specification. The transmission assembly will need to be replaced if the end play is with in specification.
PIP3720D2017-08-15. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.
PIP50722017-08-15. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have slip in forward ranges immediately after replacing the input housing. Technician will inspect the 3-4 clutches and the forward clutch oil feed passages for leakage between circuits. Technician should apply regulated compressed air to the 3-4 clutch feed hole and the forward clutch feed hole one at a time with the input housing. Technician will need to replace the input housing if there is an air leak 3-4 clutches.
40302007-06-15. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. NEW DESIGN FRONT AXLE SIDE BEARING ADJUSTERS. *KB
3012B2004-08-23. Service bulletin. POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE). THE NVG 136 ALL WHEEL DRIVE (AWD) TRANSFER CASE AND THE 236 AND 246 NVG SELECTABLE TRANSFER CASES OPERATING IN THE AUTO MODE MAY EXHIBIT A CONDITION OF A VIBRATION/SHUDDER DURING LOW SPEED TURNS SUCH AS A PARKING LOT MANEUVER, UP TO APPROXIMATELY 5 MPH. *TT 3012A NOT YET RECEIVED. *TT
30022004-08-23. Service bulletin. POWER TRAIN. 4L60E/4L65E INTERMITTENT NEUTRAL CONDITION WHILE ACCELERATING FROM A STOP OR WHILE DRIVING. *TT 1999-2006 GM CARS, LIGHT DUTY TRUCKS AND UTILITIES. *TT
014092003-11-22. Service bulletin. POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE). THE NVG 136 ALL WHEEL DRIVE (AWD) TRANSFER CASE AND THE 236 AND 246 NVG SELECTABLE TRANSFER CASE SHUDDER ON TURNS. *TT
020421005A2003-04-15. Service bulletin. POWER TRAIN. SLIPS IN 4-WHEEL DRIVE, NOISE, VIBRATION, LEAKS, HOT ODOR. *TT
0204210052002-10-10. Service bulletin. POWER TRAIN. SOME VEHICLES WILL NOT MOVE WHEN 4-WHEEL DRIVE IS REQUESTED, NOISE, SHUDDER, POOR PERFORMANCE, TRANSMISSION / TRANSFER CASE SLIPS, TRANSMISSION WILL NOT UPSHIFT, SLIPS IN 4-WHEEL DRIVE. *TT

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.