Service bulletins for the 2022 Ford Transit
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
162 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| TSB 23-2154 | 2023-05-23. Service bulletin. BACK OVER PREVENTION:SOFTWARE; POWER TRAIN. 2021-2022 F-150 vehicles with 2.7L, 3.3L, 3.5L EcoBoost or 5.0L engines, 2020-2022 Transit vehicles with 3.5L Duratec/3.5L EcoBoost engines, 2021-2023 Bronco with the 2.3L or 2.7L engine having charging system diagnostics performed in the Workshop Manual (WSM) may experience the generator voltage desired (GENVDSD) parameter identification (PID) missing from the powertrain control module (PCM) PID list in the Ford Diagnosis And Repair System (FDRS) scan tool. This may be due to a software parameter in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM. |
|---|---|
| TSB 23-2138 | 2023-05-23. Service bulletin. POWER TRAIN. Some 2022 Aviator/Bronco/Expedition/Explorer/F-150/Mustang/Navigator/Ranger/Transit vehicles built on or before 31-Jul-2022 equipped with a 10R60/10R80/10R80 MHT automatic transmission may exhibit a fluid leak from the selector shaft seal. This may be caused by a crack in the manual shaft. To correct this condition, follow the Service Procedure to replace the manual shaft, the manual shaft-to-sensor roll pin and the selector shaft seal. |
| SSM 51563 | 2023-05-04. Service bulletin. ELECTRICAL SYSTEM. Some 2021-2023 Transit, 2022-2023 E-Transit vehicles built on or before 17-feb-2023 may exhibit an uncommanded/erratic wipers and/or washer operation. It may also exhibit diagnostic trouble code (DTC) B1131, an inoperative left headlamp, and/or inoperative horn. This may be due to a poor connection at ground G110 in the left side of the engine compartment. To correct the condition, inspect ground G110 and verify eyelet anti-rotational tab is properly located and ground fastener is properly secured. Refer to Wiring Diagram, Cell 010. For claiming, use causal part 14401 and M-Time. |
| SSM 51531 | 2023-05-04. Service bulletin. POWER TRAIN. Some 2020-2023 Explorer/Aviator/Transit, 2021-2023 F-150/Bronco, 2022-2023 Expedition/Navigator/Mustang and 2023 F-250/F-350 Super Duty vehicles may exhibit harsh/delayed engagement and/or harsh/delayed shift concerns. These may be addressed with the powertrain control module (PCM)/transmission control module (TCM) Transmission Accelerated Main Control Break In Routine and/or a main control overhaul. Refer to Workshop Manual (WSM), Section 307-01, DTC Chart if DTCs are present and/or Diagnosis By Symptom to identify the clutch(s) to be cycled. Cycling the shift solenoids and clutch control valves to remove contamination must be performed along with an adaptive drive cycle before attempting repair. For claiming, use causal part 7A100 and applicable labor operations in Section 7 of the Service Labor Time Standards (SLTS) Manual. |
| SSM 51513 | 2023-04-06. Service bulletin. ELECTRICAL SYSTEM. Some 2021-2023 Ford and Lincoln vehicles may exhibit a condition where the high voltage battery stops charging when connected to level 1 or level 2 chargers with an illuminated malfunction indicator lamp (MIL) and diagnostic trouble code (DTC) P2C94 stored in the secondary on-board diagnostic control module A (SOBDM). To restore charging capability, disconnect the off-board charging station charge handle from the vehicle charge port and reconnect. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in June 2023. Replacement of the SOBDM will not resolve this condition. Monitor OASIS for additional information. |
| SSM 51449 | 2023-04-05. Service bulletin. EQUIPMENT:ELECTRICAL. Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPass®/LincolnWay® app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| SSM 51419 | 2023-04-04. Service bulletin. POWER TRAIN. Some 2017-2023 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability. |
| SSM 51412 | 2023-04-04. Service bulletin. STRUCTURE:BODY:DOOR. Some 2021-2022 Transit vehicles may exhibit a rear door that does not open or close correctly. The vehicle may also exhibit a condition of the rear door swinging all the way open. This may be due to the rear door switch. Inform customers the operation of the rear door switch has been updated in the Owner´s Manual. Refer Owner´s Manual (HTML), section Doors and Locks > Operating the doors from outside your vehicle > Opening and Closing the Doors. If the rear door switch is not damaged but the issue is still present, remove the switch and inspect the internal latch system. Remove the rear door panel and the plastic shield, with a hooked hand tool unclip the lock switch from inside the door and push down the top and the bottom clip to release the switch. To reinsert the switch, position it in the neutral stage and push it into the door. |
| SSM 51407 | 2023-04-04. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Some 2021-2022 Ford and Lincoln vehicles equipped with SYNC 4 may experience an error message during the gateway module (GWM) software update application which states Procedure Unsuccessful- GetConfigDataFromGIVIS. This may be the result of a server related concern. To correct the condition, download and run the Ford Diagnosis and Repair System (FDRS) application GWM-Read the Gateway Module A (GWM) Configuration Data application. When the application completes, refresh and re-attempt the GWM-Gateway Module A (GWM) Software Update application. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| TSB 23-2014 | 2023-04-04. Service bulletin. ELECTRICAL SYSTEM. This article supersedes TSB 22-2355 to update the vehicle model years affected. Some 2021-2023 Mustang Mach-E, 2022-2023 e-Transit and F-150 Lightning vehicles may experience inoperative level 3 charging with an illuminated Charger Service Required indicator in the instrument panel cluster (IPC) and diagnostic trouble codes (DTCs) P0D93:00, P0D94:00, P0D98:00, P0D9E:00 and/or P0DA0:00 in the secondary on-board diagnostic module (SOBDM). If the charging cord is removed from the charge port without the lock/release button fully pressed, this can damage the charge port locking pin actuator and disable level 3 charging for the next charging session. To correct the condition, follow the Service Procedure to replace only the charge port lock actuator. |
| TSB 23-2034 | 2023-03-04. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Some 2022 Transit vehicles may exhibit a DTC U0198:00 stored in the APIM but does not exhibit any customer concerns around the vehicle location or global positioning system (GPS). This may be due to the software in the gateway module (GWM). To correct the condition, follow the Service Procedure to reprogram the GWM. |
| SSM 51379 | 2023-03-04. Service bulletin. ELECTRICAL SYSTEM. Some 2021-2023 F-150/Transit, 2022-2023 F-150 Lightning vehicles may experience issues utilizing the Smart Hitch, ProPower Onboard or Onboard Scales features (if equipped) in the FordPass app. Symptoms may include inability to connect, incorrect data displayed in the app, no weight displayed, unable to power on/off the feature, unable to turn on generator mode (gas vehicles only). The connection for these features has been removed from the Android version of the FordPass app, and will soon be removed from the iOS version. The Smart Hitch and Onboard Scales will also be removed in a future FordPass release expected no later than March 1st, 2023. Full functionality of these features will remain in vehicle, but will not be controllable from FordPass. Advise the customer of the FordPass changes and do not perform any repairs for this concern. |
| SSM 51370 | 2023-03-04. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:PRESSURE/TEMPERATURE SENSOR. Some 2022-2023 Transit/E-Transit vehicles may experience an inaccurate air discharge temperature when the EATC is operating in auto or manual mode and the temperature set to 60°F (15.5°C) or above. During this condition, the system commands full or mostly heat and the air discharge temperature will only reduce in the LO setting. This may be due to calibration in the heating, ventilation and air conditioning (HVAC) module. Engineering is aware of the concern and is currently working on a solution, expected in 2nd Quarter 2023. Inform the customer that Ford is currently investigating this concern and they can continue to drive the vehicle. Monitor OASIS for updates. |
| SSM 51306 | 2023-02-02. Service bulletin. ELECTRICAL SYSTEM. Some 2018-2023 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150 - G401, Expedition/Navigator - G403, Transit - G401, 2018-2019 Explorer G302, 2020-2022 Explorer/Aviator - G407) and confirm FPCM connector (F-150 - C4336, Expedition/Navigator - C433, Transit - C433, 2018-2019 Explorer - C3239, 2020-2022 Explorer/Aviator - C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components. |
| SSM 51295 | 2023-01-31. Service bulletin. ELECTRICAL SYSTEM; STEERING:ELECTRIC POWER ASSIST SYSTEM. Some 2020-2022 Transit, 2022 E-Transit vehicles built on or before 26-Apr-2022 may exhibit a lack of power steering assist at initial vehicle start-up with diagnostic trouble code (DTC) C102D:00 stored in the power steering control module (PSCM). This may be due to the PSCM software. To correct this condition, update the PSCM to the latest software level using the latest version of Ford Diagnosis and Repair System (FDRS) tool. If the DTC C102D:00 returns, continue with diagnostics and repair direction from Workshop Manual, Section 211-02. For claiming, use causal part 3504 and applicable labor operations in Sections 10 of the Service Labor Time Standards (SLTS) Manual. |
| SSM 51290 | 2023-01-31. Service bulletin. EXTERIOR LIGHTING:TURN SIGNAL; ELECTRICAL SYSTEM. Some 2022 Transit vehicles built on or before 01-Sep-2022 with halogen lamp assemblies may exhibit a turn signal indicator fast flashing in the instrument cluster panel (IPC) with diagnostic trouble code(s) (DTC) B123A and/or B123B stored in the body control module (BCM). This may be due to a front turn signal lamp socket being internally damaged. To correct this condition, replace the affected front turn lamp socket before replacing the BCM. |
| TSB 23-2015 | 2023-01-31. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING. 2021-2022 F-150 vehicles with 2.7L, 3.3L, 3.5L EcoBoost or 5.0L engines, 2020-2022 Transit vehicles with 3.5L Duratec/3.5L EcoBoost engines, 2023 Bronco with the 2.3L engine having charging system diagnostics performed in the Workshop Manual (WSM) may experience the generator voltage desired (GENVDSD) parameter identification (PID) missing from the powertrain control module (PCM) PID list in the Ford Diagnosis And Repair System (FDRS) scan tool. This may be due to a software parameter in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM. |
| SSM 51261 | 2023-01-06. Service bulletin. SERVICE BRAKES. Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00. |
| SSM 51253 | 2023-01-05. Service bulletin. BACK OVER PREVENTION:SOFTWARE; ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR; EQUIPMENT:ELECTRICAL. Some 2022 Transit vehicles that are not equipped with a telematics control unit (TCU) module and built on or before 28-Mar-2022 may exhibit a no crank/no start condition due to a discharged battery. If no parasitic draw is found during normal diagnostics, run the GWM - Gateway Module A (GWM) Configuration application using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool to correct the condition. For claiming, use causal part 14F642 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| SSM 51228 | 2023-01-05. Service bulletin. COMMUNICATION:MANUFACTURER TELEMATICS. Some 2020-2023 Ford and Lincoln vehicles equipped with a telematic control unit (TCU) may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| TSB 22-2496 | 2023-01-05. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM:PROPULSION SYSTEM:TRACTION MOTOR:CONTROLLER:SOFTWARE. This article supersedes TSB 22-2402 to update the vehicle model years affected. Some 2021-2022 Mustang Mach-E base model (non-GT) built on or before 25-Jul-2022, 2022-2023 e-Transit vehicles built on or before 17-Sep-2022 may experience an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P1A3C, U3000:16, U3000:64, U3000:04 and/or U3000:45 in the off-board charging controller (OBCC) module and the high voltage (HV) battery will not charge using a level 3 direct current (DC) fast charging station/electrical vehicle supply equipment (EVSE). This may be due to OBCC software. To correct the condition, follow the Service Procedure to reprogram the OBCC. |
| TSB 22-2491 | 2023-01-05. Service bulletin. ELECTRICAL SYSTEM. Some 2021-2022 Mustang Mach-E built on or before 17-Sep-2022, 2022 e-Transit vehicles may exhibit an illuminated red triangle indicator lamp with diagnostic trouble code (DTC) P27B4 stored in the secondary on-board diagnostic control module C (SOBDMC) or the charge status indicator (CSI) is blinking red with DTC P0A7F stored in the battery energy control module (BECM) and/or P0CF7 stored in the secondary on-board diagnostic control module A (SOBDM). This may be due to an unsecured plug-in electric vehicle supply equipment (EVSE). To correct the condition, follow the Service Procedure to reprogram the SOBDM. |
| TSB 22-2471 | 2023-01-05. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:PROPULSION SYSTEM. This article supersedes TSB 21-2205 to update the vehicles and vehicle model years affected. 2021-2022 F-150 vehicles with 2.7L, 3.5L EcoBoost or 5.0L engines, 2020-2022 Transit vehicles with 3.5L EcoBoost engine having charging system diagnostics performed in the Workshop Manual (WSM) may experience the generator voltage desired (GENVDSD) parameter identification (PID) missing from the powertrain control module (PCM) PID list in the FDRS. This may be due to a software parameter in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM. |
| TSB 22-2444 | 2022-12-02. Service bulletin. UNKNOWN OR OTHER; POWER TRAIN:DRIVELINE:DRIVESHAFT; POWER TRAIN. This article supersedes TSB 22-2271 to update the vehicle model years affected. Some 2015-2023 Transit vehicles equipped with rear wheel drive (RWD), single rear wheel (only), and U-joints at the transmission flange and rear driveshaft may experience a boom/hum/moan noise from the rear while driving. This noise is most noticeable at highway speeds: 112-121 km/h (70-75 mph) for 4.10 axle ratio 121-128 km/h (75-80 mph) for 3.73 axle ratio 136-145 km/h (85-90 mph) for 3.31 axle ratio The noise may also be present to a lesser degree at roughly half of the noted speeds. This may be due to a 2nd order driveline frequency transmitted through the rear driveshaft, rear axle and into the body through the leaf springs. To correct the condition, follow the Service Procedure to install a driveshaft torsional damper. NOTE: The torsional damper will not resolve a vibration. |
| SSM 51191 | 2022-11-30. Service bulletin. POWER TRAIN. Some 2021-2022 Mustang Mach-E built on or before 17-Jan-2022, 2022 Escape built on or before 03-Mar-2022, Bronco Sport built on or before 04-Mar-2022, 2022 Maverick built on or before 25-Jan-2022 and 2022 Transit built on or before 17-May-2022 may exhibit a powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0929:77 stored in the gear shift module (GSM). This may be due to the software in the GSM. To correct this condition, perform Pinpoint Test D. Refer to Workshop Manual (WSM), Section 307-05 > Diagnosis and Testing. If the GSM is not operating correctly, perform the replacement of the GSM. Do not perform a PMI after installing a new GSM assembly. The GSM is shipped with the latest software level. For claiming, use causal part 7P155 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.