Service bulletins for the 2021 Ford Mustang
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
148 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Transmission and driveline are shown. Show all
| SSM 51419 | 2023-04-04. Service bulletin. POWER TRAIN. Some 2017-2023 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability. |
|---|---|
| TSB 23-2020 | 2023-01-31. Service bulletin. POWER TRAIN. Some 2021-2022 Mustang Mach-E vehicles built on or before 28-May-2022 may exhibit an illuminated malfunction indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P0563, P0ADA, P0ADE, P0AA1, P0AA4, P0AA5, P0AA2, P0D10, P0D0F, and/or P0C78 stored in battery energy control module (BECM). It may also have a low/discharged 12V battery and/or display a Stop Safely Now message in the instrument panel cluster (IPC). This may be due to the high voltage battery junction box (HVBJB). To correct the condition, follow the Service Procedure to replace the HVBJB and reprogram the BECM. |
| SSM 51236 | 2023-01-05. Service bulletin. POWER TRAIN. Some 2018-2022 Mustang vehicles equipped with a 5.0L engine and a 10R80 transmission may exhibit a buck/jerk sensation that may be perceived as an engine misfire during throttle tip-in between 35-45 mph (56-72 km/h) and with the transmission in 8th, 9th, or 10th gear. This buck/jerk sensation is a characteristic of the vehicle and can be compared to a like vehicle that is equipped with a similar powertrain (engine, transmission, and rear end gear ratio) driven in the same manner. A diagnostic trouble code (DTC) will not set because of this condition and no repair attempts should be made. If a misfire DTC is present, the DTC should be diagnosed first following the correct diagnostic procedure outlined in the Workshop Manual, Section 303-07B. |
| SSM 51232 | 2023-01-05. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. Some 2018-2022 Mustang vehicles equipped with a 5.0L engine and a 10R80 transmission may exhibit a buck/jerk sensation that may be perceived as an engine misfire during throttle tip-in between 35-45 MPH (56-72 KPH) and with the transmission in 8th, 9th, or 10th gear. This buck/jerk sensation can be compared to a like vehicle that is equipped with a similar powertrain (engine, transmission, and rear end gear ratio) and driven in the same manner. A diagnostic trouble code (DTC) will not set because of this condition. If a misfire DTC is present, the DTC should be diagnosed first following the correct diagnostic procedure outlined in the Workshop Manual, Section 303-07B. |
| TSB 22-2339 | 2022-09-23. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Some 2018-2021 Expedition/Navigator, 2018-2020 F-150/Mustang and 2019-2021 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P163E stored in the powertrain control module (PCM) or transmission control module (TCM) after replacing the main control valve body. This may be due to software incompatibility between the replacement main control valve body solenoid strategy file and the PCM/TCM software. To correct this condition, follow the Service Procedure to enter only the 13-digit solenoid body strategy when downloading transmission strategy. |
| TSB 22-2280 | 2022-07-18. Service bulletin. EQUIPMENT; POWER TRAIN:MANUAL TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2020-2021 Mustang GT500 vehicles may experience erratic and harsh shifting at highway speeds and/or perceived lack of power when accelerating from a stop, with a powertrain malfunction (wrench) indicator and diagnostic trouble codes (DTCs) P1601 and/or P061A stored in the powertrain control module (PCM) while using SelectShift. This may be due to the software in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM. |
| TSB 22-2185 | 2022-05-16. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2021-2022 Mustang vehicles built on or before 21-Apr-2022 and equipped with a 2.3L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) and diagnostic trouble codes (DTC) P0300 and/or P0316 in the powertrain control module (PCM). This may be due to various strategies within the PCM software. To correct the condition, follow the Service Procedure to reprogram the PCM. |
| SSM 50756 | 2022-05-16. Service bulletin. POWER TRAIN. Some 2020-2021 Mustang GT500 vehicles may experience erratic and harsh shifting at highway speeds and/or reduced speed when accelerating from a stop, with a powertrain malfunction (wrench) indicator and DTCs P1601/P061A while using SelectShift. This may be due to powertrain control module (PCM) calibration. This condition does not affect vehicle durability and no additional diagnosis or service is required at this time. Inform customers that they can continue to drive the vehicle but not to use SelectShift. Engineering is currently working on a solution for this condition that is expected in June 2022. Replacement or reprogramming of the PCM will not resolve this condition at this time. Schedule a follow-up appointment for repair in June 2022. Once the update becomes available, contact the customer and confirm the service appointment. Monitor OASIS for updates. |
| TSB 22-2139 | 2022-04-26. Service bulletin. POWER TRAIN; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. Some 2017-2020 F-150, 2018-2022 Expedition/Navigator/Mustang and 2019-2022 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware break-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle. |
| SSM 50555 | 2022-03-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN. Some 2020-2021 Mustang GT500 vehicles may experience erratic and harsh shifting at highway speeds and/or reduced speed when accelerating from a stop, with a powertrain malfunction (wrench) indicator and DTCs P1601/P061A while using SelectShift. This may be due to powertrain control module (PCM) calibration. This condition does not affect vehicle durability and no additional diagnosis or service is required at this time. Inform customers that they can continue to drive the vehicle but not to use SelectShift. Engineering is currently working on a solution for this condition that is expected in April 2022. Replacement or reprogramming of the PCM will not resolve this condition at this time. Schedule a follow-up appointment for repair in April 2022. Once the update becomes available, contact the customer and confirm the service appointment. Monitor OASIS for updates. |
| TSB 21-2423 | 2022-01-01. Service bulletin. POWER TRAIN. Some 2018-2021 Expedition/Navigator, 2018-2020 F-150/Mustang and 2019-2021 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P163E stored in the powertrain control module (PCM) or transmission control module (TCM) after replacing the main control valve body. This may be due to software incompatibility between the replacement main control valve body solenoid strategy file and the PCM/TCM software. To correct this condition, follow the Service Procedure to obtain a new main control valve body with a new strategy number. |
| TSB 21-2357 | 2022-01-01. Service bulletin. POWER TRAIN. This article supersedes TSB 21-2315 to increase the labor operation time allowances. Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang and 2019-2021 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware wear-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle. |
| TSB 21-2390 | 2021-12-02. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Some 2020-2021 Mustang GT500 vehicles built on or before 30-June-2021 may exhibit a no crank/no start with no powertrain control module (PCM) communication condition if the oil level is approximately 1 or more quarts low and the oil life is at or less than 20%. This may be due to various parameters within the PCM. To correct the condition, follow the Service Procedure to reset and reprogram the PCM. |
| TSB 21-2346 | 2021-11-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Some 2021 Mustang vehicles equipped with a 2.3L engine and a 6-speed manual transmission MT82 built on or before 24-Sep-2021 may exhibit an illuminated MIL and diagnostic trouble codes (DTC) P0300 and/or P0316 in the powertrain control module (PCM). This may be due to various strategies within the PCM software. To correct the condition, follow the Service Procedure to reprogram the PCM. |
| TSB 21-2315 | 2021-10-05. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION. Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang and 2019-2021 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware wear-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle. |
| TSB 21-2330 | 2021-09-30. Service bulletin. POWER TRAIN. Some 2020 Mustang GT350 - 2020-2021 Mustang Mach 1/Shelby GT500 vehicles may exhibit a rear differential fluid leak at the differential cooler line fittings. This may be due to a seal within the fittings. To correct the condition, follow the service procedure to replace both rear differential cooler line fittings. |
| TSB 21-2294 | 2021-09-30. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); POWER TRAIN:MANUAL TRANSMISSION:INTERNAL:DOGS/SYNCHROS. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software. |
| TSB 21-2284 | 2021-09-04. Service bulletin. POWER TRAIN. Some 2020-2021 Mustang GT500 vehicles may exhibit a clatter noise/vibration in reverse (R) at 3-8 mph (5-13 km/h) and/or an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P175C, P175D, P175E, P0844, P0849 and/or P0874 set in the transmission control module (TCM). This may be due to the software in the TCM. To correct the condition, follow the Service Procedure steps to check the transmission fluid pressure sensor and reprogram the PCM/TCM. |
| TSB 21-2148 | 2021-09-04. Service bulletin. POWER TRAIN. Some 2020-2021 Mustang GT500 vehicles may exhibit a transmission fluid leak caused by improperly seated or cracked transmission cooler tubes attached to the transmission case. This may be due to the retaining bolts being cross threaded causing the seals to leak and/or crack the lines. If the threads in the transmission case that the cooler tube retaining bolts go into are damaged, it is not necessary to replace the transmission. These threads can be repaired. To correct the condition, follow the Service Procedure to repair these threads and replace the tubes. |
| SSM 50049 | 2021-09-04. Service bulletin. POWER TRAIN:MANUAL TRANSMISSION:INTERNAL:DOGS/SYNCHROS. Some 2017-2021 Ford and Lincoln vehicle customers may receive a message in their FordPass or Lincoln Way App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription. |
| TSB 21-2174 | 2021-07-01. Service bulletin. POWER TRAIN. Some 2021 Mustang vehicles equipped with a 5.0L engine and built on or before 11-Feb-2021 may exhibit an intermittent rough running drivability concern with an illuminated malfunction indicator lamp (MIL) and diagnostic trouble codes (DTC) P0351, P0352, P0353 and/or P0354 stored in the powertrain control module (PCM). This may be due to a software parameter within the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM. |
| SSM 49821 | 2021-06-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE AND ENGINE COOLING. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| TSB 21-2108 | 2021-05-04. Service bulletin. POWER TRAIN. Some 2020-2021 Mustang GT500 vehicles may exhibit a transmission fluid leak caused by improperly seated transmission cooler tubes attached to the transmission case. If the threads in the transmission case that the cooler tube retaining bolts go into are damaged, it is not necessary to replace the transmission. These threads can be repaired. To correct the condition, follow the Service Procedure to repair these threads. |
| SSM 49581 | 2021-03-03. Service bulletin. POWER TRAIN. Some 2020-2021 Mustang GT500 vehicles may exhibit various transmission related concerns and/or DTCs. In addition to following normal Workshop Manual (WSM) diagnostics, inspect C105, an inline connector next to the right side valve cover, for signs of pushed out terminals, terminal damage, or harness damage. If any pushed out terminals, terminal damage, or harness damage is found, repair as necessary. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.