WenmarOpen by Wenmar Pro

Service bulletins for the 2013 Ford Fusion

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

229 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
TSB1600752021-12-20. Service bulletin. ENGINE. Hard start/no start/loss of engine RPM after refueling - built on or before 11/09/2013
TSB1600452021-12-20. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE. 2.0L Ecoboost - Fuel odor
TSB1600012021-12-20. Service bulletin. FUEL/PROPULSION SYSTEM; ENGINE; EQUIPMENT; POWER TRAIN; AIR BAGS; STRUCTURE. 49 CFR Part 579.5 Monthly Communications - March 2016 Air bag warning light illuminated with diagnostic trouble code (DTC) B141B and/or B141C
LTR37562021-12-20. Service bulletin. FUEL/PROPULSION SYSTEM; AIR BAGS; ENGINE; STRUCTURE; POWER TRAIN; ELECTRICAL SYSTEM. 49 CFR Part 579.5 Monthly Communications - January 2016
SSM 492102020-10-06. Service bulletin. ENGINE AND ENGINE COOLING. Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
SSM 485982020-03-03. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. 2013-2018 C-Max, 2013-2020 Fusion Hybrid/MKZ Hybrid vehicles may exhibit a MIL with Diagnostic Trouble Code (DTC) P0340 and/or P0344. This may occur due to excessive moisture build up in the engine oil. Excess moisture occurs when the vehicle is driven short distances and/or less than 6,000 combined miles per year. To correct the condition, replace the camshaft position sensor (CMP) and change the engine oil. Advise the customer to perform more frequent oil changes and allow the internal combustion engine to reach operating temperature when running to prevent reoccurrence. Refer to the owners guide - maintenance - engine oil check - operating in cold climates and short driving cycles.
TSB 19-22072019-07-03. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. Some 2013-2017 C-Max/Fusion/MKZ Hybrid/Energi vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1450, P0456, P0457, P04EE and/or P04EF. This may be due to the sealing capability of the canister purge valve. To correct the condition, follow the Service Procedure steps to update the PCM software and replace the canister purge valve.
SSM 479482019-05-07. Service bulletin. ENGINE. SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
SSM 477902019-04-08. Service bulletin. ELECTRICAL SYSTEM; ENGINE. Some 2013-2019 Fusion/MKZ and 2013-2018 C-Max vehicles with 2.0L HEV/PHEV engine may exhibit multiple drivability or electrical concerns with one or more diagnostic trouble codes, being the most common P26C3, P26CA, P26D0, P2800, P2802, U019F and U0284. On Fusion/MKZ inspect connectors C146, C1651, C1812, C168C, C1717 and C134 for signs of water entry or corrosion. On C-Max, inspect connectors C134, C140, C144, C1651, C1717 and C1812 and service as necessary. NOTE: Connector C1717 is only equipped on PHEVs for both Fusion and C-Max.
SSM 476622019-01-07. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
TSB 18-22552018-09-24. Service bulletin. ENGINE. Some 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost, 2013-2018 Fusion vehicles equipped with 2.0L/2.7L EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.
SSM 470002018-06-11. Service bulletin. ENGINE; POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE). Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
SSM 470002018-05-29. Service bulletin. ENGINE AND ENGINE COOLING. Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
SSM 460852017-08-01. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE); ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS; ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY; ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV); ENGINE AND ENGINE COOLING:COOLING SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:ENGINE:DIESEL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS; ENGINE AND ENGINE COOLING:ENGINE; ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.
SSM 463272017-03-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. 2013-2016 FIESTA, ESCAPE, TRANSIT CONNECT AND 2013 FUSION VEHICLES WITH A 1.6L GASOLINE TURBOCHARGED DIRECT INJECTION (GTDI) ENGINE MAY EXHIBIT AN ENGINE OIL LEVEL READING THAT IS UP TO 8 MM ABOVE THE MAXIMUM MARK ON THE ENGINE OIL DIPSTICK WHEN THE ENGINE IS FILLED WITH THE CORRECT AMOUNT OF OIL. THIS IS A NORMAL CHARACTERISTIC OF THIS ENGINE. DO NOT LOWER THE OIL LEVEL TO THE MAXIMUM MARK ON THE ENGINE OIL DIPSTICK IF THE ENGINE CONTAINS THE CORRECT AMOUNT OF OIL. ADDING OIL IS NOT REQUIRED IF THE LEVEL IS ABOVE THE MINIMUM MARK ON THE ENGINE OIL DIPSTICK. REFER TO THE OWNERS MANUAL FOR PROPER ENGINE OIL CAPACITY.
SSM 462952017-03-15. Service bulletin. ENGINE. TO HELP DIFFERENTIATE ENGINE OIL LEAKS FROM OTHER POSSIBLE SOURCES, A NEW WHITE-COLORED FLUORESCENT ENGINE OIL DYE IS AVAILABLE. WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.
TSB16-01012017-02-10. Service bulletin. ELECTRICAL SYSTEM; ENGINE. SOME 2013-2014 FOCUS ST, FUSION, ESCAPE AND VEHICLES EQUIPPED WITH A 2.0L GASOLINE TURBOCHARGED DIRECT INJECTION (GTDI) ENGINE AND BUILT ON 9/1/2012 AND THROUGH 8/1/2013 MAY EXHIBIT AN ILLUMINATED MALFUNCTION INDICATOR LAMP (MIL) WITH DIAGNOSTIC TROUBLE CODE (DTC) P2096 (POST CATALYST FUEL TRIM SYSTEM TOO LEAN BANK 1) STORED IN POWERTRAIN CONTROL MODULE (PCM) MEMORY. THIS MAY BE DUE TO ENGINE OIL MIGRATING FROM THE VARIABLE VALVE TIMING (VVT) OIL CONTROL SOLENOIDS THROUGH THE ENGINE WIRE HARNESS TO THE CATALYST MONITOR SENSOR (CMS). FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
16-00312016-06-22. Service bulletin. ELECTRICAL SYSTEM; ENGINE. ISSUE Some 2013-2014 Focus ST, Fusion, Escape and MKZ vehicles equipped with a 2.0L gasoline turbocharged direct injection (GTDI) engine and built on 9/1/2012 and through 8/1/2013 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2096 (post catalyst fuel trim system too lean bank 1) stored in powertrain control module (PCM) memory. This may be due to engine oil migrating from the variable valve timing (VVT) oil control solenoids through the engine wire harness to the catalyst monitor sensor (CMS).
ASI-451612016-06-22. Service bulletin. ENGINE. SUMMARY TO BE PROVIDED ON A FUTURE DATE.
15-01622016-06-22. Service bulletin. ENGINE. SUMMARY TO BE PROVIDED ON A FUTURE DATE.
ASI-452202015-10-21. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. LINCOLN/FORD: ADVANCE TRAC LAMP OR MALFUNCTION INDICATOR LAMP (MIL) WILL BE ON WITH VARIOUS DIAGNOSTIC TROUBLE CODES (DTC) REGARDING EVAPORATIVE EMISSIONS LEAK DETECTION CONTROL MODULE AND POSSIBLE REPLACEMENT, IF CORROSION IS FOUND. MODEL 2013-15 FUSION, MKZ HYBRID. *PE
ASI-446572015-06-23. Service bulletin. ELECTRICAL SYSTEM:STARTER ASSEMBLY; ENGINE. FORD: THERE IS AN INTERMITTENT DELAY ENGAGEMENT OF STARTER OR CRANKING ENGINE, ON SOME VEHICLES, WHEN IGNITION KEY HAS BEEN TURNED TO START. MODEL 2013 FUSION S, SE. *PE
TSB-14-01292015-03-17. Service bulletin. ENGINE. FORD: STORED IN POWERTRAIN CONTROL MODULE (PCM) MEMORY ARE VARIOUS DIAGNOSTIC TROUBLE CODES (DTC), ALONG WITH MALFUNCTION INDICATOR LAMP ILLUMINATING (MIL) AND INFORMATION PROVIDED TO CORRECT THE ISSUE. MODEL 2013 ESCAPE, FUSION. *PE
TSB-14-01292015-01-28. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE. FORD/LINCOLN: DIAGNOSTIC TROUBLE CODE (DTC) P0132, P0135, P0030, P2243, P2251 ARE STORED IN POWERTRAIN CONTROL MODULE (PCM) MEMORY AND CAUSES MALFUNCTION INDICATOR LAMP (MIL) TO ILLUMINATE. MODEL 2013 ESCAPE, FUSION, MKZ. *PE
TSB-14-00862014-11-14. Service bulletin. ENGINE; EXTERIOR LIGHTING:HEADLIGHTS. FORD/LINCOLN: WHEN HEADLAMP SWITCH IS IN AUTOLAMP POSITION, AFTER ENGINE START UP, THE AMBIENT LIGHTING IS INOPERATIVE, INTERMITTENTLY AND BODY CONTROL MODULE (BCM) NEEDS REPROGRAMMING TO LATEST CALIBRATION. MODEL 2013-2014 FUSION, MKZ. *PE

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.