WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Ford F-450

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

329 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
TSB 19-22312019-08-06. Service bulletin. POWER TRAIN. Some 2017-2019 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1291, P1292, P0191 and/or P06A6. This may be due to an engine harness chafe on the powertrain control module (PCM) bracket. Before completing Powertrain Control/Emissions Diagnosis (PC/ED) Manual pinpoint tests, follow the Service Procedure steps.
SSM 479762019-06-07. Service bulletin. POWER TRAIN. On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
TSB19-21602019-06-05. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2017-2019 F-Super Duty vehicles equipped with a 6.7L engine built on or before 9-Jan-2019 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P2074, P0401, P0402 and/or P0170. This may be due to various strategies within the powertrain control module (PCM) software. To resolve this condition, follow the Service Procedure steps to reprogram the PCM and perform a mass air flow (MAF) parameter reset. Follow the service procedure steps to correct the condition.
SSM 478232019-04-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE. Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
TSB 19-20532019-04-02. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. Some 2017-2019 F-Super Duty chassis cab/dual rear wheel (DRW) pickup vehicles and 2016- 2019 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an oil consumption concern in applications where the engine is idled for extended periods of time. This may be due to high crankcase pressure as a result of the crankcase ventilation filter element becoming restricted. To resolve the concern, replace the crankcase vent oil separator. The new crankcase vent oil separator appears different from the old crankcase vent oil separator as it no longer includes a serviceable filter element.
SSM 478232019-04-01. Service bulletin. POWER TRAIN. Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
SSM 475972018-11-19. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); EQUIPMENT. Some 2013-2019 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated MIL with only DTC P2074 stored in the powertrain control module (PCM). This may be due to a dirty air filter, replace the filter if necessary. Do not replace the PCM or mass air flow (MAF) sensor for this concern. Instead perform a MAF parameter reset under: Toolbox > Powertrain > Service Functions > Reset/Clear Specified Function > Reset/Clear Functions > MAF Sensor. Engineering is investigating. Monitor OASIS for updates.
SSM 470392018-05-29. Service bulletin. POWER TRAIN. Some 2017 F-Super Duty, 2016-2017 F650-750 equipped with 6.7L diesel engines and 2015-2017 Transit equipped with 3.2L diesel engines may exhibit a MIL on with diagnostic trouble code (DTC) P206C stored in powertrain control module(PCM). This may be due to incorrect diesel exhaust fluid (DEF) concentration. Prior to performing Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test RJ, ensure DEF concentration is checked using Central Tools Refractometer tool number CEN3R201 and if DEF contamination is suspected use the Rotunda Hydrocarbon Test Kit tool number 328-480508.
TSB18-20152018-05-29. Service bulletin. POWER TRAIN. Some 2017 F-Super Duty vehicles equipped with a 6.7L diesel engine may exhibit a fuel knock type noise at idle, illuminated MIL with one or more of the following DTCs stored in powertrain control module (PCM) memory: P0263, P0266, P0269, P0272, P0275, P0278, P0281, P0284, P2B11, P2B13, P2B15, P2B17, P2B19, P2B1B, P2B1D, and/or P2B1F. This may be due to incorrect learning of the injector timing within the PCM. Follow the Service Procedure steps to correct the condition.
SSM 471702018-05-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. Some vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB18-21002018-05-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2017 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated MIL with diagnostic trouble code (DTC) U029D and/or P2209 in the powertrain control module (PCM). This may be due to water intrusion. Follow the Service Procedure steps to correct the condition.
SSM 469212018-01-29. Service bulletin. FUEL SYSTEM, DIESEL; POWER TRAIN. Some 2017 F-Super Duty vehicles with 6.7L diesel engines may exhibit a fuel knock type noise at idle with various cylinder contribution/balance DTCs and/or Fuel Injector Offset Learn DTCs. To resolve this issue please use the following procedure: 1) Make sure ECT1 and EOT are above 176Å?F (80Å?C). 2) Using the IDS or FJDS, run the Manual Injector Balance Test/Enhanced Power Balance Test under Toolbox, Powertrain, Power Balance. If the noise is gone after running the Enhanced Power Balance test, then clear the High Pressure Side Minimum Fuel Mass Adaptation tables for all cylinders, and the Crankshaft Position Sensor under Toolbox, Powertrain, Service Functions, Reset, Clear Specified Function. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.
SSM 469002018-01-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
SSM 464662017-05-22. Service bulletin. POWER TRAIN. THE 2017 POWERTRAIN CONTROL/EMISSIONS DIAGNOSIS (PC/ED) MANUAL HAS BEEN REVISED FOR DIAGNOSING ELECTRONIC THROTTLE BODY (ETB). FOR ALL ETB CONCERNS, THE APPROPRIATE DIAGNOSTIC MUST BE COMPLETED BEFORE THROTTLE BODY REPLACEMENT. IF A CONCERN IS INTERMITTENT AND NO DTCS ARE PRESENT, REFER TO HISTORICAL DTCS AND THE PC/ED, SECTION 3 NO DTCS PRESENT INDEX CHART FOR FURTHER INFORMATION.
SSM 464512017-05-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. 2009-2017 VEHICLES EQUIPPED WITH A 6R80, 6R100, 6R140 AUTOMATIC TRANSMISSION HAVE AN UPDATED MAIN CONTROL VALVE BODY OVERHAUL PROCEDURE. REFER TO WORKSHOP MANUAL (WSM), SECTION 307-01 FOR MAIN CONTROL VALVE BODY (7A100) OVERHAUL PROCEDURES. NOT ALL VALVE BODIES REQUIRE REPLACEMENT. INSPECT THE VALVE BODY BORES, SPRINGS AND VALVES AS DIRECTED DURING DIAGNOSIS AND REPAIR. REFER TO GENERAL SERVICE BULLETIN (GSB) G0000093 AUTOMATIC TRANSMISSION MAIN CONTROL INSPECTION FOR A VIDEO CLIP TO AID IN THE DIAGNOSIS OF THESE REPAIRS.
TSB 16-01522017-03-20. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). SOME 2017 F-SUPER DUTY VEHICLES EQUIPPED WITH A 6.7L ENGINE BUILT ON OR BEFORE 24-OCT-2016 MAY EXHIBIT DTC P0402 IN THE POWERTRAIN CONTROL MODULE (PCM). THIS MAY BE DUE TO A MASS AIR FLOW (MAF) SENSOR ADAPTION FEATURE WHICH HAS NOT YET LEARNED THE APPROPRIATE VALUES FOR THE VEHICLE OPERATING CONDITION. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
SSM 464162017-03-20. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). SOME 2017 F-SUPER DUTY AND 2016-2017 F-650/F-750 VEHICLES EQUIPPED WITH A 6.7L ENGINE MAY EXHIBIT A DTC P0000. THIS DTC IS DUE TO A PROCESSING ERROR IN THE POWERTRAIN CONTROL MODULE (PCM) AS A RESULT OF ON DEMAND SELF TESTING WITH AN INTEGRATED DIAGNOSTIC SYSTEM (IDS). P0000 IS AN INVALID DTC THAT WILL NOT ILLUMINATE THE MIL AND SHOULD BE DISREGARDED.
TSB 17-00202017-03-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). SOME 2017 F-SUPER DUTY, 2016-2017 F650/750 VEHICLES BUILT ON OR BEFORE 20-DEC-2016 AND EQUIPPED WITH A 6.7L ENGINE MAY EXHIBIT AN ILLUMINATED MIL WITH DIAGNOSTIC TROUBLE CODE (DTC) P20E8 IN THE POWERTRAIN CONTROL MODULE (PCM) MEMORY. THIS MAY BE DUE TO AIR TRAPPED IN THE REDUCTANT LINES CAUSING THE REDUCTANT PUMP AND HEATER ASSEMBLY TO NOT BUILD SUFFICIENT SYSTEM PRESSURE OR LOOSE REDUCTANT LINE CONNECTIONS. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
TSB 17-00172017-03-17. Service bulletin. POWER TRAIN. SOME 2017 F-SUPER DUTY VEHICLES EQUIPPED WITH A 6.7L ENGINE AND BUILT ON OR BEFORE 20-FEB-2017 MAY EXHIBIT AN ILLUMINATED MIL WITH DIAGNOSTIC TROUBLE CODES (DTCS) P20EE, P2002, P2201, P246C AND/OR P2463. REPROGRAM THE POWERTRAIN CONTROL MODULE (PCM) TO THE LATEST CALIBRATION USING IDS RELEASE 104.02 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM.
SSM 462662017-03-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN. THE 2017 POWERTRAIN CONTROL/EMISSIONS DIAGNOSIS (PC/ED) MANUAL HAS BEEN REVISED FOR DIAGNOSING ELECTRONIC THROTTLE BODIES (ETBS). FOR ALL ETB CONCERNS, THE APPROPRIATE DIAGNOSTIC MUST BE COMPLETED BEFORE THROTTLE BODY REPLACEMENT. IF A CONCERN IS INTERMITTENT AND NO DTCS ARE PRESENT, REFER TO HISTORICAL DTCS AND THE PC/ED, SECTION 3 NO DTCS PRESENT INDEX CHART FOR FURTHER INFORMATION.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.