WenmarOpen by Wenmar Pro

Service bulletins for the 2019 Ford F-250

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

249 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
SSM 521672024-01-18. Service bulletin. ELECTRICAL SYSTEM. Some 2017-2019 F-Super Duty pick-up vehicles may require the additional KC3Z-14A411-C kit if there is a service need to replace the 14405 main body harness or 14A412 tailgate harness post FSA 19S48. During the FSA 19S48 repair, additional connectors are added to the 14405 and 14A412 that utilize the jumper service kit contained in the FSA. Direction regarding the need for this harness is also noted in the Ford parts catalog.
SSM 519472023-10-06. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Some 2015-2019 F-Super Duty and 2015-2020 F-150/Mustang vehicles may require replacement of the powertrain control module (PCM) for various reasons. While performing a programmable module installation (PMI) using the Integrated Diagnostic Service (IDS) scan tool, an error message may state: Configuration Failed, Would You Like To Retry? This may be due to improper module replacement steps. Make sure that the original module is installed in the vehicle, delete the vehicle session, then start a new vehicle session. Once the session starts, run the PCM PMI and install the new PCM only when the scan tool instructs. Finish the PMI by following the prompts given by IDS. If the original PCM is not available, it is possible to configure the module by running as-built programming on the PCM. When IDS asks to obtain part numbers or configuration data, select configuration data.
SSM 519372023-10-05. Service bulletin. EQUIPMENT. Some vehicles equipped with power folding mirrors may exhibit power folding mirrors that are inoperative or exhibit a clicking sound. This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.
SSM 518382023-09-04. Service bulletin. ELECTRICAL SYSTEM. In various 2017-2023 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.
SSM 518542023-09-04. Service bulletin. POWER TRAIN:MANUAL TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS > Diagnostics tab > HVBoM > Features > Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
SSM 518492023-09-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
SAN-Vol1 I12023-08-16. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
SSM 518292023-08-14. Service bulletin. EQUIPMENT; VISIBILITY:REARVIEW MIRRORS/DEVICES. Some F-Super Duty and F-150 vehicles equipped with trailer tow mirror may exhibit various exterior rear view mirror functional concerns that require replacement after diagnosis. To properly determine if the defect is warrantable, cleaning and close inspection of the affected mirror may be required. To aid in proper warranty determination, the Rear-View Mirror Analysis general service bulletin (GSB) has been updated with a detailed cleaning procedure that should be followed prior to any inspection. New labor operations (17682ZZ or 17682ZZT) have been created that covers the cleaning and inspection process and may be used even if condition of failure is non-warrantable. Ford has inspected numerous returned parts and determined many cases are caused by damage which is unwarrantable and may be subject to chargeback. Refer to the latest version of the GSB on OASIS.
22M032023-07-07. Service bulletin. LANE DEPARTURE: SENSING SYSTEM: CAMERA; EQUIPMENT ADAPTIVE/MOBILITY; FORWARD COLLISION AVOIDANCE: SENSING SYSTEM: CAMERA. Certain 2017-2020 Model Year Continental and Super Duty, 2018-2020 Navigator, 2020 Aviator, and 2020 Explorer Vehicles Replace Front and/or Side Cameras if Foggy
SSM 516912023-06-16. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; POWER TRAIN. 2011-2023 F-Super Duty and 2016-2024 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an elevated idle condition. During prolonged idle time, vehicles may experience this elevated idle to reduce unburned hydrocarbons from the SCR. The powertrain control module estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 RPM for ambient temperatures near 26°C (80°F) and may increase to 1200 RPM at -40 °C (-40°F). Vehicles may exhibit exhaust smoke and diesel exhaust fluid smell during elevated idle condition. Exhaust smoke and smell condition will not affect reliability or durability of the engine. Power take-off (PTO) use and idle set point control will disable elevated speed. It is required that the operator monitor the vehicle and adhere to any Exhaust Filter warning messages.
20N04 S22023-06-06. Service bulletin. POWER TRAIN; EQUIPMENT. Certain 2017-2019 MY F250/F350 and all F450/550 vehicles Steering Linage Damper replacement. Reason for this supplement: Updated program terms, includes new mobile service repair assessment and updated owner letters with revised program terms.
TSB 23-21612023-05-31. Service bulletin. ELECTRICAL SYSTEM. Some 2018-2021 F-150 vehicles equipped with a 3.0L diesel engine, 2016-2022 F-650/F-750 vehicles equipped with a 6.7L engine, and 2017-2022 F-Super Duty vehicles equipped with a 6.7L engine and built on or before 08-Mar-2022 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P21DD, P20BA. P20B9, P204C, P208A, P208B, P208C, P203B, P205B, P21CD and/or U02A2 in the powertrain control module (PCM). This may be due to water intrusion within connectors C3613 and/or C4851/C3610 on the reductant harness going to the reductant pump/heater assembly and the reductant level sensor/quality module. This may also be due to movement of the wiring harness causing terminal fretting. To correct the condition, follow the Service Procedure to replace the reductant tank harness, the reductant pump/heater assembly and/or the reductant tank, as well as securing the wiring harness using a cable zip tie fastener.
SSM 515362023-05-04. Service bulletin. STRUCTURE. For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
TSB 23-21152023-05-04. Service bulletin. EQUIPMENT. Some 2015-2020 F-150 and 2017-2022 F-Super Duty vehicles may exhibit a lack of heat or cooling from the cabin vents when the climate control settings are adjusted between hot and cold. This may be due to a stuck/binding temperature door within the climate control housing or binding/inoperative temperature door actuator. Diagnostic trouble code (DTC) B1081:07 may be present in the front controls interface module (FCIM) or heating ventilation and air conditioning (HVAC) module. To correct the condition, follow the Service Procedure to remove the climate control housing and replace the temperature door cam(s), lubricate the temperature blend door bearing surface, and apply flock tape to actuator to seal out debris.
SSM 512942023-01-31. Service bulletin. ENGINE AND ENGINE COOLING. Some 2016-2019 F-Super Duty/F-650/F-750 vehicles equipped with a 6.7L engine may require the lower intake manifold to be removed for various concerns. The WSM, Section 303-01, has been updated to remove the lower intake manifold leaving the crankcase vent oil separator attached. Both parts should be removed from the engine together to avoid discarding and replacing the crankcase vent oil separator.
SSM 512652023-01-06. Service bulletin. VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR; EQUIPMENT. Some vehicles equipped with power folding mirrors may exhibit power folding mirrors that are inoperative or exhibit a clicking sound. This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.
SSM 512632023-01-06. Service bulletin. BACK OVER PREVENTION; STRUCTURE:BODY:DOOR. Some 2015-2023 F-150, 2017-2022 F-Super Duty, and 2019-2023 Ranger vehicles may exhibit dust ingress into the cabin through the doors or air extractors. This may be due to the climate control system being in recirculation mode as a result of the recirculation button being on or automatic strategies for heating/cooling efficiency. To minimize dust ingress when driving in off-road or secondary road conditions, make sure that all doors and windows are fully closed and the climate control system is switched to defrost on and the instrument panel and footwell air vents are switched to off. Temperature and fan settings may be adjusted as desired. Alternatively, max defrost can be activated which will adjust all settings automatically. Operating in defrost mode will keep constant air flow through the rear air extractors and other small areas, helping minimize dust ingress.
SSM 512612023-01-06. Service bulletin. SERVICE BRAKES. Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 512512023-01-05. Service bulletin. ENGINE AND ENGINE COOLING. Some 2011-2022 F-Super Duty vehicles equipped with a 6.7L diesel engine may exhibit a ticking noise at idle after an engine oil change. It is often referred to as Typewriter Noise because of its similarity to the sound of a mechanical typewriter. When engine temperatures reach 150 °F (65 °C) or higher, (from engine idle up to approximately 1700 RPM's), this noise can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. Typewriter Noise is not detrimental to engine function or durability and has no short or long term effects on the engine. Do not attempt repairs to eliminate this noise. This noise is characteristic of the 6.7L diesel engine and will typically cease or diminish significantly within the oil change maintenance interval.
21M05 S32022-12-02. Service bulletin. LATCHES/LOCKS/LINKAGES:FUELING/CHARGING DOOR/HATCH/PORT:LATCH/LOCK RELEASE SYSTEM; UNKNOWN OR OTHER; ELECTRICAL SYSTEM:WIRING; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Certain 2017-2022 Model Year Super Duty Vehicles Equipped with a Power Release Tailgate - Unintended Tailgate Opening REASON FOR THIS SUPPLEMENT Technical Information: Updated with revised instructions to account for wiring harness changes that were implemented into production and changes to the tailgate latch control assembly removal and installation procedures. As a result, the Labor Allowances and Parts Requirements / Ordering Information have also been updated accordingly. Parts Requirements/Ordering Information: All parts are on open order. Special Service Support Center (SSSC) contact is no longer required to order tailgate actuator ground wiring kit.
SSM 511852022-11-30. Service bulletin. STRUCTURE:BODY:TAILGATE. Some 2015-2022 F-150 and 2017-2022 F-Super Duty vehicles may experience issues with the tailgate center step moulding. If there is an issue with the center molding (warped, damaged condition, loose, or if the molding is missing), the trim cover is now available separately. It is no longer necessary to replace the entire rear step assembly (402A48).
TSB 22-23942022-11-01. Service bulletin. LATCHES/LOCKS/LINKAGES:DOORS:LOCK. Some 2019-2020 F-150 and F-Super Duty vehicles may exhibit one or more power door locks inoperative. This concern may be due to a power door lock actuator. To correct the condition, follow the Service Procedure to replace the affected actuator.
TSB 22-23892022-11-01. Service bulletin. WHEELS. Some 2017-2020 F-Super Duty vehicles equipped with dual rear wheels (DRW) and 17 inch aluminum wheels may exhibit a loss of tire pressure from the valve stem sealing area of the front wheels. This may be due to corrosion of the wheel preventing the valve stem from sealing properly. To correct the condition, follow the Service Procedure to clean the corrosion from the valve stem sealing area of the affected wheel.
TSB 22-23802022-10-31. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2019 F-Super Duty chassis cab/dual rear wheel (DRW) pickup vehicles and 2016-2019 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit a concern of oil consumption in applications where the engine is idled for extended periods of time. This may be due to high crankcase pressure as a result of the crankcase ventilation filter element becoming restricted. To correct the condition, follow the Service Procedure to replace the crankcase oil separator and to inspect the turbocharger to determine whether the turbocharger needs to be replaced. Note: The new crankcase vent oil separator appears different from the old crankcase vent oil separator as it no longer includes a serviceable filter element.
SSM 511222022-10-11. Service bulletin. ELECTRICAL SYSTEM:STARTER ASSEMBLY. Some 2017-2022 F-250-F-550, 2015-2020 F-150 and 2018-2022 Expedition vehicles without push button start and passive entry may exhibit a condition where it is difficult to insert the ignition key and/or turn it to the accessory position when removing the ignition lock cylinder per the functional lock cylinder service procedure in Workshop Manual (WSM), Section 501-14. This may be due to debris or contamination in the ignition lock cylinder. If this concern occurs, use a suitable shop vacuum to dislodge or remove debris or contamination by placing the vacuum hose over the lock cylinder, without the key installed, for 30 seconds. Insert the ignition key and reattempt turning it to the accessory position for lock cylinder removal. If the key will not turn to the accessory position, continue with the non-functional lock cylinder removal procedure.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.