Service bulletins for the 2017 Ford F-150
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
343 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| TSB 20-2034 | 2020-03-03. Service bulletin. EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:WATER HEATER; SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER. Some 2015-2019 F-150 vehicles equipped with a 3.3L, 3.5L Duratec, 3.5L EcoBoost and 5.0L engine and equipped with a block heater built on or before 1-Jan-2019 may exhibit a lack of heat concern from the heating ventilation and air conditioning (HVAC) system when operating the vehicle consistently in temperatures that are below -20Å’C (4Å’F). This condition may be due to deposits from the engine coolant becoming trapped in the heater core. To correct the condition, flush the cooling system and replace the heater core. |
|---|---|
| TSB-20-2028 | 2020-03-03. Service bulletin. SERVICE BRAKES, HYDRAULIC:POWER ASSIST:VACUUM; EQUIPMENT. Some 2013-2018 F-150/Expedition/Navigator vehicles equipped with 4-wheel drive (4WD) may exhibit an intermittent grinding noise while driving in 2-wheel drive (2WD) mode most commonly on acceleration. This may be due to a loss of vacuum to the integrated wheel end (IWE) actuators and/or wear of the IWE components. To correct the condition, follow the Service Procedure steps to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components. |
| TSB-20-2016 | 2020-03-03. Service bulletin. STEERING:LINKAGES:DRAG:POWER ASSIST SYSTEM. Some 2017 F-150 vehicles equipped with a 3.5L EcoBoost engine may exhibit a rattle type noise from the engine compartment under various operating conditions. This noise may be due to excessive play the turbocharger wastegate linkage. To correct the condition, follow the Service Procedure to install the wastegate linkage spring kit. |
| SSM 48490 | 2020-02-04. Service bulletin. ELECTRICAL SYSTEM; VISIBILITY. Some 2015-2020 F-150 and 2017-2020 F-Super Duty vehicles equipped with a rear defroster may have factory installed or service replacement rear glass that uses rear defroster electrical terminals with a plastic overmolded cover. The rear glass defroster terminals are not serviceable and should not be removed or detached from the glass during diagnosis or repairs. If the rear glass defroster terminals are separated from the glass, the rear glass assembly must be replaced. |
| SSM 48445 | 2020-02-04. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2018 F-150 vehicles built on or before 10-Jul-2018 and 2018-2019 Expedition/Navigator vehicles built on or before 8-Apr-2019 with 3.5L EcoBoost may exhibit tick, tap, or rattle type noises from top of engine front cover for 2-5 seconds after a cold start. Replace all 4 VCT units (6256/6C525) and update the PCM calibration. Do not replace other camshaft timing related components unless inspection identifies a concern. Refer to the Workshop Manual, Section 303-01. Claim labor to replace VCTs using published labor operations and PCM programming using M-time. Dealers should order parts only when required to complete a repair. Once the parts are ordered, the vehicle may be returned to the customer to drive. This condition does not affect long term durability or performance. |
| SSM 48439 | 2020-02-04. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2020 F-150 and 2018-2020 Expedition/Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04DB stored in the powertrain control module (PCM). The regulatory monitor for DTC P04DB is sensitive to crankcase system pressure concerns such as oil level indicator o-ring seal, incorrectly installed oil level indicator, crankcase hose, vacuum hose disconnects and oil fill cap o-rings. If root cause is unidentified after inspecting for loose or incorrectly installed crankcase pressure system components, perform Pinpoint Test HG in the Powertrain Control/Emissions Diagnosis (PC/ED) manual. |
| TSB 20-2015 | 2020-02-04. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2018 F-150 vehicles equipped with a 3.5L EcoBoost engine built at Kansas City Assembly Plant on or before 23-Feb-2018 or Dearborn Truck Plant on or before 26-Feb-2018 and Expedition/Navigator vehicles built on or before 19-Mar-2018 may exhibit an oil leak from the oil pan RTV seal. This may be due to a lack of RTV adhesion. This article includes detailed steps to achieve proper RTV adhesion. To correct the condition, follow the Service Procedure steps to replace the oil pan. |
| TSB 20-2013 | 2020-02-04. Service bulletin. WHEELS. Some 2013-2018 F-150/Expedition/Navigator vehicles equipped with 4-wheel drive (4WD) may exhibit an intermittent grinding noise while driving in 2-wheel drive (2WD) mode most commonly on acceleration. This may be due to a loss of vacuum to the integrated wheel end (IWE) actuators and/or wear of the IWE components. To correct the condition, follow the Service Procedure steps to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components. |
| SSM 48423 | 2020-01-08. Service bulletin. POWER TRAIN. Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| SSM 48404 | 2020-01-08. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2017-2020 F-150 vehicles equipped with a 3.5L EcoBoost engine, 2018-2020 F-150 vehicles equipped with a 2.7L EcoBoost or 5.0L engine, 2019-2020 F-150 vehicles equipped with a 3.0L engine, and an externally controlled variable displacement compressor (EVDC) may exhibit a high pitched squeal or whistle type noise from the engine compartment after the engine is shut off. This condition may be due to the air conditioning (A/C) low side system pressure exceeding the high side pressure resulting in equalization of A/C system pressures through the EVDC A/C compressor. This noise is not detrimental to system operation or durability. Do not attempt diagnosis or repairs for this condition at this time. Engineering is investigating, monitor OASIS for updates. |
| TSB 19-2390 | 2020-01-07. Service bulletin. ELECTRICAL SYSTEM; SEATS. Some 2015-2019 F-150, 2015-2020 Explorer, 2017-2019 F-Super Duty, 2017-2020 Continental, 2018-2020 Expedition/Navigator, 2016-2018 MKX, 2019-2020 Nautilus, 2020 Aviator/Corsair and 2013-2020 MKZ vehicles equipped with multi-contour seats may exhibit intermittent multi-contour seat operation and/or massage and lumbar adjust inoperative from the seat switch or SYNC screen with or without diagnostic trouble code (DTC) B1471, U024B, and/or U024C. This may be due to terminal fretting at the connector for the driver multi-contour seat module (SCMG) and passenger multi-contour seat module (SCMH). To correct the condition, follow the Service Procedure steps to replace the connectors and reroute the harness. |
| TSB 19-2384 | 2020-01-07. Service bulletin. ENGINE AND ENGINE COOLING. Some 2016-2017 F-150 vehicles equipped with a 2.7L EcoBoost engine and built on 1-Apr-2016 and through 1-Jan-2017 may exhibit a rough idle in neutral or park at normal operating temperature with oil consumption greater than 1 liter (1 quart) in less than 4,800 km (3,000 miles). This may be due to a concern with the cylinder head valve guides. Vehicles with this condition may also exhibit an illuminated malfunction indicator lamp (MIL) and diagnostic trouble codes (DTCs) P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0316, P0524 and/or P06DD with the excessive oil consumption. Blue smoke may also be present from the exhaust only after a hot restart. To correct the condition, follow the Service Procedure to replace the cylinder heads. |
| TSB19-2374 | 2020-01-07. Service bulletin. STRUCTURE. Some 2015-2019 F-150, 2017-2019 F-Super Duty, 2018-2019 Expedition/Navigator vehicles may exhibit a rattle and/or squeak noise from the vista roof opening panel while driving with the roof opening panel closed. This may be due to dirt and/or debris build up between the vista roof opening panel seal and the body. To correct the condition, follow the Service Procedure steps to clean and lubricate the vista roof opening panel seal. |
| 18N03-S7 | 2019-12-05. Service bulletin. STRUCTURE; LATCHES/LOCKS/LINKAGES:DOORS:LATCH. Customer Satisfaction Program 18N03 - Supplement #7 Certain 2015-2018 Model Year F-150 and 2017-2018 Model Year F-250-F-550 Vehicles - Door Latch Freezing Concerns |
| SSM 48340 | 2019-12-05. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2019 vehicles equipped with SYNC 3 may experience a map displayed on the left half of the SYNC screen with no other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state. |
| SSM 48322 | 2019-12-05. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2019 F-150 vehicles equipped with a 3.5L EcoBoost engine may exhibit an illuminated MIL with DTC P04DB stored in the powertrain control module (PCM). Regulatory monitor for DTC P04DB is sensitive to crankcase system pressure concerns such as oil level indicator o-ring seal, incorrectly installed oil level indicator, crankcase hose, vacuum hose disconnects and oil fill cap o-rings. If root cause is unidentified after inspection for loose, incorrectly installed crankcase pressure system concerns, perform Pinpoint Test HG. |
| SSM 48316 | 2019-12-05. Service bulletin. ELECTRICAL SYSTEM. Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229. |
| TSB 19-2341 | 2019-12-04. Service bulletin. EQUIPMENT; STRUCTURE. This article supersedes TSB 19-2285 to update the vehicle model years affected and Service Procedure. Some 2015-2020 F-150 vehicles may exhibit a glove compartment door that is difficult to latch on one or both sides or appears misaligned along the storage tray or right side instrument panel when closed. This may be due to the position of the glove compartment storage tray rubber mat or the seating of the glove compartment door strikers or glove compartment door hinge pins. To correct the condition, follow the Service Procedure steps to reposition or adjust the affected component. |
| SSM 48260 | 2019-11-05. Service bulletin. ELECTRICAL SYSTEM. Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229. |
| SSM 48272 | 2019-11-05. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Some 2017-2018 F-150s built on or before 10-Jul-2018 and 2018-2019 Expedition and Navigator built on or before 8-Apr-2019 with 3.5L EcoBoost may exhibit tick, tap, or rattle type noises from top of engine front cover for 2-5 seconds after a cold start. A TSB is expected to be published late 4th quarter 2019. In the interim, replace all 4 VCT units and update the PCM calibration. Do not replace other cam drive related components unless inspection identifies a concern. Refer to the Workshop Manual (WSM), Section 303-01. Claim labor replace VCTs using published labor operations and PCM programming using M-time. Part availability is currently limited. Dealers should order parts only when required to complete a repair. Once the parts are ordered, the vehicle may be returned to the customer to drive. This condition does not affect long term durability or performance. |
| TSB 19-2285 | 2019-11-05. Service bulletin. UNKNOWN OR OTHER. This article supersedes TSB 19-2206 to update the Title, Issue Statement and Service Procedure. Some 2015-2019 F-150 vehicles may exhibit a glove compartment door that is difficult to latch on one or both sides or appears misaligned along the storage tray or right side instrument panel when closed. This may be due to the position of the glove compartment storage tray rubber mat or the seating of the glove compartment door strikers or glove compartment door hinge pins. To correct the condition, follow the Service Procedure steps to reposition or adjust the affected component. Follow the Service Procedure steps to correct the condition on vehicles that meet all of the following criteria: * 2015-2019 F-150 * Glove compartment door is difficult to latch on one or both sides or appears misaligned |
| TSB 19-2293 | 2019-10-04. Service bulletin. SEATS:FRONT ASSEMBLY:POWER ADJUST; SEATS. Some 2015-2019 F-150/Explorer, 2017-2019 F-Super Duty/Continental, 2018-2019 Expedition/Navigator, 2016-2018 MKX, 2019 Nautilus, and 2013-2019 MKZ vehicles equipped with Multi-Contour seats may exhibit intermittent multi-contour seat operation and/or massage and lumbar adjust inoperative from the seat switch or SYNC screen with or without diagnostic trouble code (DTC) B1471, U024B, and/or U024C. This may be due to terminal fretting at the connector for the driver multi-contour seat module (SCMG) and passenger multi-contour seat module (SCMH). To correct the condition, follow the Service Procedure steps to replace the connectors and reroute the harness. |
| SSM 48168 | 2019-10-04. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2018 F-150 vehicles built on or before 10-Jul-2018 and 2018-2019 Expedition/Navigator vehicles built on or before 8-Apr-2019 equipped with a 3.5L EcoBoost engine may exhibit a ticking, tapping, or rattle type noise from the top front cover area of the engine that last 2-5 seconds on initial start-up after a cold soak. This may be due to a worn variable cam timing (VCT) unit. A TSB is expected to be published 4th quarter of 2019. In the interim, replace all 4 VCT units and update the powertrain control module (PCM) calibration. Do not replace timing chains, tensioners, guides or other timing related components unless inspection clearly identifies a concern. Refer to the Workshop Manual (WSM), Section 303-01. Claim the labor required to replace VCTs using published labor operations and PCM programming using M-time. Monitor OASIS for updates. |
| SSM 48135 | 2019-09-09. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions. |
| SSM 48130 | 2019-09-06. Service bulletin. VISIBILITY:GLASS, SIDE/REAR; VISIBILITY. Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.