Service bulletins for the 2017 Ford F-150
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
343 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| TSB 24-2098 | 2024-04-04. Service bulletin. ENGINE AND ENGINE COOLING. This article supersedes TSB 23-2330 to update the Parts List. Some 2015-2017 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit an oil leak from the oil pan RTV seal. This may be due to various concerns with the oil pan. To correct the condition, follow the Service Procedure to replace the oil pan with the later style oil pan. |
|---|---|
| SSM 52335 | 2024-03-20. Service bulletin. ENGINE AND ENGINE COOLING. For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed. |
| SSM 52334 | 2024-03-20. Service bulletin. ENGINE AND ENGINE COOLING. Some 2011-2024 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a tick tap and/or typewriter ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150°F (65°C) or higher and engine speed is at idle up to approximately 1700 RPM. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise tick rate can be faster or slower and is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted. This information along with an example audio clip has been added to the WSM Section 303-00 Engine System General Information > Diagnosis and Testing > Engine > PPT F > Step F2. |
| TSB 23-2330 | 2024-03-07. Service bulletin. ENGINE AND ENGINE COOLING. This article supersedes TSB 23-2083 to update the Service Procedure and the Part List. Some 2015-2017 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit an oil leak from the oil pan RTV seal. This may be due to various concerns with the oil pan. To correct the condition, follow the Service Procedure to replace the oil pan with the later style oil pan. |
| TSB 23-2143 | 2023-05-31. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. Some 2017-2020 F-150 and 2018-2020 Expedition/Navigator vehicles built on or before 30-Nov-2019 and equipped with a 3.5L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. Some vehicles may also exhibit an intermittent condition with no auto restart during auto-start-stop operation with or without diagnostic trouble code (DTC) P164C present in the powertrain control module (PCM). This may be due to a worn variable camshaft timing (VCT) unit. To correct the condition, follow the Service Procedure to replace the VCT units. |
| TSB 23-2083 | 2023-04-04. Service bulletin. ENGINE AND ENGINE COOLING. Some 2015-2017 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit an oil leak from the oil pan RTV seal. This may be due to various concerns with the oil pan. To correct the condition, follow the Service Procedure to replace the oil pan with the later style oil pan. |
| SSM 51296 | 2023-01-31. Service bulletin. ENGINE AND ENGINE COOLING. Some 2015-2020 F-150 vehicles equipped with a 2.7L, 3.5L or 5.0L engine may require replacement of the long block engine assembly. New service kits have been released which include all the one-time-use components required in the service procedure for removal and replacement of the long block engine assembly. Refer to the Ford Electronic Parts Catalog (ECAT) for long block service kit part number by application. |
| TSB 22-2200 | 2022-05-24. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2020 F-150 2018-2020 Expedition/Navigator vehicles built on or before 31-Oct-2019 and equipped with a 3.5L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure steps to replace the VCT units. |
| 21N03-S4 | 2022-04-04. Service bulletin. ENGINE AND ENGINE COOLING. Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine - Cam Phase Replacement. Parts Requirements / Order information - Intake Gaskets HL3Z-9439-A should be inspected and only replaced if damaged. It is no longer required to replace these gaskets. |
| TSB 22-2089 | 2022-03-15. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN; UNKNOWN OR OTHER. Some 2015-2022 F-150, 2017-2022 F-Super Duty and 2018-2022 Expedition/Navigator vehicles may exhibit poor air conditioning (A/C) performance, loss of airflow and/or engine cooling fans running continuously from high A/C pressures. This concern may be from the evaporator freezing up due to the evaporator temperature sensor being biased. To correct the condition, follow the Service Procedure steps to replace the evaporator temperature sensor. |
| SSM 50445 | 2022-02-04. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2021 F-150 vehicles built on or before 01-Feb-2021, 2017-2020 F-150 vehicles equipped with a 3.5L EcoBoost engine, 2018-2020 F-150 vehicles equipped with a 2.7L EcoBoost or 5.0L engine, 2019-2020 F-150 vehicles equipped with a 3.0L diesel engine may exhibit a high pitched squeal or whistle type noise from the engine compartment after the engine is shut off. This condition may be due to the air conditioning (A/C) low side system pressure exceeding the high side pressure resulting in equalization of A/C system pressures through the A/C compressor. An updated A/C compressor has been released to resolve this concern. For claiming, use causal part 19703 and applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual. |
| TSB 21-2404 | 2022-02-04. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE. Some 2015-2021 F-150, 2017-2021 Super Duty and 2018-2021 Expedition/Navigator vehicles may exhibit poor air conditioning (A/C) performance, loss of airflow and/or engine cooling fans running continuously from high A/C pressures. This concern may be from the evaporator freezing up due to the evaporator temperature sensor being biased. To correct the condition, follow the Service Procedure steps to replace the evaporator temperature sensor. |
| 21N03-S3 | 2021-12-07. Service bulletin. ENGINE AND ENGINE COOLING. Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine Cam Phaser Replacement REASON FOR THIS SUPPLEMENT • Parts Requirements / Ordering Information - Due to limited availability of originally specified parts, alternate option parts have been added. • Submitting Claims with Customer Loyalty Program for Balance Remaining – Added instructions on how to use Lincoln Loyalty funds. |
| 21N08 | 2021-11-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE; ENGINE. Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine PCM Reprogram Due to Engine Shudder; Owner Letter sent |
| TSB 21-2250 | 2021-09-30. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. Some 2015-2020 F-150, 2017-2020 Super Duty and 2018-2020 Expedition/Navigator vehicles may exhibit poor air conditioning (A/C) performance, loss of airflow and/or engine cooling fans running continuously from high A/C pressures. This concern may be from the evaporator freezing up due to the evaporator temperature sensor being biased. To correct the condition, follow the Service Procedure steps to replace the evaporator temperature sensor. |
| SSM 50089 | 2021-09-28. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE. Some 2017-2021 Ford and Lincoln vehicles equipped with 3.3L, 3.5L EcoBoost, or 5.0L engines may exhibit stalling, lack of power, low fuel rail pressure and/or DTCs P0087 or P008A after a repair was made that required the removal of the fuel line that connects the high-pressure fuel pump to the port injection rail, such as injector replacements or base engine repairs. This line must be installed in the correct orientation as it has an internal one-way check valve. To determine if the fuel line has been installed improperly, look at the position of the Oetiker clamp (stainless band clamped around the black fuel line). The clamp holds the one-way check valve in place and should be located closest to the end connected to the port injection rail. If the clamp is not closest to the port injection rail, remove and reinstall the line in the proper orientation. |
| 21N03 | 2021-09-05. Service bulletin. ENGINE AND ENGINE COOLING. In some of the affected vehicles, an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after the vehicle was turned off for an extended period of time or as a knocking noise when the engine is idling after it is warmed up. These concerns should be addressed by the updated calibration provided in FSA 21B10. However, for peace of mind, Ford is providing an extended warranty for customers who receive the PCM update under program 21B10 prior to December 21, 2021 and continue to experience cam phaser noise after receiving that PCM update. |
| 21B10-S2 | 2021-09-05. Service bulletin. ENGINE AND ENGINE COOLING. It may be possible that an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after your vehicle was turned off for an extended period of time, or as a knocking noise when the engine is idling after it is warmed up. |
| 21N03-S1 | 2021-08-02. Service bulletin. ENGINE AND ENGINE COOLING. In some of the affected vehicles, an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after the vehicle was turned off for an extended period of time or as a knocking noise when the engine is idling after it is warmed up. These concerns should be addressed by the updated calibration provided in FSA 21B10. However, for peace of mind, Ford is providing an extended warranty for customers who receive the PCM update under program 21B10 prior to December 31, 2021 and continue to experience cam phaser noise after receiving that PCM update, A cam phaser that has developed an undesirable noise does not affect the vehicle safety, performance, or emissions. |
| 21B10-S2 | 2021-08-02. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING. In some of the affected vehicles, an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after the vehicle was turned off for an extended period of time, or as a knocking noise when the engine is idling after it is warmed up. A cam phaser that has developed an undesirable noise does not affect the vehicle safety, performance, or emissions. |
| SSM 49821 | 2021-06-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE AND ENGINE COOLING. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| TSB 21-2119 | 2021-05-04. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2020 F-150 2018-2020 Expedition/Navigator vehicles built on or before 31-Oct-2019 and equipped with a 3.5L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure steps to replace the VCT units. |
| SSM 49761 | 2021-05-03. Service bulletin. ENGINE AND ENGINE COOLING. Some 2011-2021 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150F (65Å’C) or higher and engine speed is at idle up to approximately 1700 RPMs. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted. |
| 21B10 | 2021-04-03. Service bulletin. ENGINE AND ENGINE COOLING. Certain 2017-2020 Model Year F-150 Equipped with a 3.5L GTDI Engine Powertrain Control Module Reprogram for Cam Phaser Rattle In some of the affected vehicles, an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after the vehicle was turned off for an extended period of time, or as a knocking noise when the engine is idling after it is warmed up. A cam phaser that has developed an undesirable noise does not affect the vehicle safety, performance, or emissions |
| 21N03 | 2021-04-03. Service bulletin. ENGINE AND ENGINE COOLING. Certain 2017-2020 Model Year F-150 Equipped with a 3.5L GTDI Engine Cam Phaser Replacement In some of the affected vehicles, an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after the vehicle was turned off for an extended period of time or as a knocking noise when the engine is idling after it is warmed up. A cam phaser that has developed an undesirable noise does not affect the vehicle safety, performance, or emissions |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.