WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Ford F-150

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

343 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
TSB 21-20842021-08-02. Service bulletin. POWER TRAIN. Some 2017-2021 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0096 in the powertrain control module (PCM). This may be due to an issue with the manifold absolute pressure (MAP) sensor. To correct the condition, follow the Service Procedure to replace the MAP sensor.
SSM 498212021-06-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE AND ENGINE COOLING. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
21B10-S12021-05-04. Service bulletin. POWER TRAIN. Certain 2017-2020 Model Year F-150 Equipped with a 3.5L GTDI Engine Powertrain Control Module Reprogram for Cam Phaser Rattle Reports of Transmission Shudder after PCM Reprogram: Dealers are instructed to stop performing this field service action until further notice. This shudder is under investigation.
TSB 21-20762021-04-03. Service bulletin. POWER TRAIN. Some 2013-2018 F-150 vehicles equipped with electronic shift on-the-fly (ESOF) 4-wheel drive (4WD) may exhibit an intermittent grinding noise while driving in 2-wheel drive (2WD) mode most commonly on acceleration. ESOF can be identified as it does not have a 4WD AUTO (4A) position on the mode selector switch (MSS). This may be due to a loss of vacuum to the integrated wheel end (IWE) actuators and/or wear of the IWE components. To correct the condition, follow the Service Procedure steps to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.
TSB 20-23062020-11-05. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES; EQUIPMENT. The service part long block for 2017-2018 F-150 vehicles equipped with a 3.5L EcoBoost engine built at Kansas City Assembly Plant on or before 23-Feb-2018 or Dearborn Truck Plant on or before 26-Feb-2018 and 2018 Expedition/Navigator vehicles built on or before 19-Mar-2018 has been changed to a one piece oil pan design. To make sure there is proper fitment of the new long block with the one piece oil pan, replacement of the transmission cooler coolant lines and an engine harness modification will be necessary. To correctly install, follow the Service Procedure steps to complete the repair.
TSB 20-22782020-11-05. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT; POWER TRAIN. Some 2013-2018 F-150 vehicles equipped with Electronic Shift On-The-Fly (ESOF) 4-wheel drive (4WD) may exhibit an intermittent grinding noise while driving in 2-wheel drive (2WD) mode most commonly on acceleration. This may be due to a loss of vacuum to the integrated wheel end (IWE) actuators and/or wear of the IWE components. To correct the condition, follow the Service Procedure steps to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.
TSB 20-21912020-07-06. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2017-2018 F-150 vehicles built on or before 10-Jul-2018 and equipped with a 3.5L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure steps to replace the VCT units and update the powertrain control module (PCM) calibration with revised VCT parameters.
TSB 20-21172020-05-05. Service bulletin. POWER TRAIN. Some 2017-2018 F-150/Raptor, 2018 Expedition/Mustang/Navigator vehicles equipped with a 10R80 automatic transmission and built on or before 20-Nov-2017 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0741 and P1744 in the powertrain control module (PCM) or transmission control module (TCM). This may be due to a sticking torque converter clutch (TCC) valve in the main control valve body assembly. To correct the condition, follow the Service Procedure to replace the main control valve body.
TSB-20-20602020-04-02. Service bulletin. POWER TRAIN. Some 2015-2017 F-150 vehicles equipped with a 6R80 transmission may experience an intermittent loss of reverse engagement, loss of the ability to shift into reverse or a neutral state when performing a specific shift pattern during manual shift events with no diagnostic trouble codes (DTCs). This may occur after shifting from MANUAL 1 or MANUAL 2 to REVERSE at low speeds while the vehicle is rolling. To correct the condition, follow the Service Procedure to reprogram the powertrain control module (PCM).
SSM 485632020-03-03. Service bulletin. POWER TRAIN; STEERING. SSM 48563 - 2017-2020 F-150 - No Crank/No Start, Multiple Illuminated Warning Indicators And/Or DTCs Some 2017-2020 F-150 vehicles may exhibit a no crank/no start, auto start stop inoperative, illuminated malfunction indicator lamp (MIL) and/or powertrain malfunction indicator lamp, transmission shift concerns, diagnostic trouble codes (DTCs) P061A, U0140, U0401, U0101, U0074 and/or U0037 being set in the powertrain control module (PCM), transmission control module (TCM), instrument panel cluster (IPC), front controls interface module (FCIM), anti-lock braking system (ABS) module and/or power steering control module (PSCM). This may be due to the 15525 transmission wire harness not being properly secured. Visually inspect the harness for possible damage and proper routing at the rear of the engine down to the transmission. Repair as necessary. If no concerns are found, proceed with normal diagnosis.
SSM 484232020-01-08. Service bulletin. POWER TRAIN. Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 19-22522019-09-06. Service bulletin. POWER TRAIN. Some 2013-2018 F-150/Expedition/Navigator vehicles equipped with four wheel drive (4WD) may exhibit an intermittent grinding noise while driving in two wheel drive (2WD) mode most commonly on acceleration. This may be due to a loss of vacuum to the integrated wheel end (IWE) actuators and/or wear of the IWE components. To correct the condition, follow the Service Procedure steps to replace the worn vacuum and/or IWE components.
SSM 480822019-08-07. Service bulletin. POWER TRAIN. Some 2015-2018 F-150/Expedition/Navigator vehicles equipped with a 3.5L/2.7L EcoBoost engine and four-wheel drive (4WD) may exhibit an intermittent grinding type noise while driving in two-wheel drive (2WD), most commonly on acceleration. This noise could appear to be turbocharger related. After engineering analysis of returned turbochargers that have been replaced for this condition, no concerns were identified with the turbochargers. The grinding type noise may be related to the 4WD system integrated wheel ends (IWE). To aid in diagnosis, shift the vehicle to 4WD and attempt to verify the condition. If the grinding noise no longer occurs with the vehicle in 4WD a IWE vacuum system and/or mechanical fault may be present.
SSM 479762019-06-07. Service bulletin. POWER TRAIN. On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
SSM 478122019-04-08. Service bulletin. POWER TRAIN. Some 2017-2019 F-150, 2018-2019 Expedition/Navigator/Mustang, 2019 Ranger vehicles equipped with a 10R80 transmission may exhibit a whine noise. This may occur at idle and while driving coming from the bell housing and front pan area of the transmission. The whine noise may become louder when at operating temperature and increases with higher engine RPM in the PARK position. A small amount of whine noise is considered to be characteristic of the 10R80 transmission due to the offset gear drivetrain in the front support and has no effect on durability.
SSM 478122019-04-01. Service bulletin. POWER TRAIN. Some 2017-2019 F-150, 2018-2019 Expedition/Navigator/Mustang, 2019 Ranger vehicles equipped with a 10R80 transmission may exhibit a whine noise. This may occur at idle and while driving coming from the bell housing and front pan area of the transmission. The whine noise may become louder when at operating temperature and increases with higher engine RPM in the PARK position. A small amount of whine noise is considered to be characteristic of the 10R80 transmission due to the offset gear drivetrain in the front support and has no effect on durability.
TSB 19-20192019-04-01. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; POWER TRAIN. Some 2018-2019 F-150 vehicles equipped with a 3.0L diesel engine built on or before 25-Jan-2019 may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0234, P208E and/or P2201 stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.
SSM 475152018-12-03. Service bulletin. POWER TRAIN. Some 2017-2018 F-150, 2018 Expedition/Navigator, 2018-2019 Mustang vehicles equipped with a 10R80 transmission may exhibit a whine noise. This may occur at idle and while driving coming from the bell housing and front pan area of the transmission. The whine noise may become louder when at operating temperature and increases with higher engine RPM in the Park position. A small amount of whine noise is considered to be characteristic of the 10R80 transmission due to the offset gear drivetrain in the front support and has no effect on durability.
TSB 18-22652018-09-24. Service bulletin. POWER TRAIN. Some 2018 F-Super Duty vehicles built on 29-Jan-2018 and through 24-Jul-2018 equipped with a 6R140 automatic transmission may experience a howl, flutter and/or whine noise typically in 4th and/or 6th gear that appears to be coming from under the dash near the right side of the steering column. This may be due to noise transferring through the shift cable into the vehicle. Follow the Service Procedure steps to correct the condition.
TSB18-21602018-07-23. Service bulletin. POWER TRAIN; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. Some 2017-2018 F-150/Raptor, 2018 Expedition/Mustang/Navigator vehicles equipped with a 10R80 automatic transmission and built on or before 20-Nov-2017 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0741 and P1744 in the powertrain control module (PCM) or transmission control module (TCM). This may be due to a sticking torque converter clutch (TCC) valve in the main control valve body assembly. Follow the Service Procedure steps to correct the condition.
SSM 471702018-05-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. Some vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB18-20792018-05-21. Service bulletin. POWER TRAIN. Some 2017 F-150/Raptor vehicles equipped with a 10R80 automatic transmission built on or before 1-Aug-2017 may exhibit harsh or delayed shifts and/or an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0711 stored in the transmission control module (TCM). Reprogram the powertrain control module (PCM) using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 108.04 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
SSM 470932018-05-14. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. 2017-2018 F-150/Raptor and 2018 Expedition/Navigator/Mustang vehicles equipped with a 10R80 automatic transmission require a new automatic transmission fluid, MERCONù Ultra Low Viscosity (ULV). It is important to positively identify the transmission and service with the correct fluid. Use only Motorcraft MERCONù ULV Automatic Transmission Fluid XT-12-QULV (WSS-M2C949-A) or equivalent when servicing a 10R80 automatic transmission. Using improper transmission fluid may result in internal transmission damage. For any further questions regarding the 10R80 transmission or fluid specification for 2017-2018 F-150 or 2018 Expedition/Mustang/Navigator Refer to WSM Section 307-01 - Specifications.
SSM 469212018-01-29. Service bulletin. FUEL SYSTEM, DIESEL; POWER TRAIN. Some 2017 F-Super Duty vehicles with 6.7L diesel engines may exhibit a fuel knock type noise at idle with various cylinder contribution/balance DTCs and/or Fuel Injector Offset Learn DTCs. To resolve this issue please use the following procedure: 1) Make sure ECT1 and EOT are above 176Å?F (80Å?C). 2) Using the IDS or FJDS, run the Manual Injector Balance Test/Enhanced Power Balance Test under Toolbox, Powertrain, Power Balance. If the noise is gone after running the Enhanced Power Balance test, then clear the High Pressure Side Minimum Fuel Mass Adaptation tables for all cylinders, and the Crankshaft Position Sensor under Toolbox, Powertrain, Service Functions, Reset, Clear Specified Function. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.
SSM 469002018-01-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.