WenmarOpen by Wenmar Pro

Service bulletins for the 2022 Ford Explorer

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

262 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
SSM 514492023-04-05. Service bulletin. EQUIPMENT:ELECTRICAL. Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPass®/LincolnWay® app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 514392023-04-05. Service bulletin. POWER TRAIN. Some 2020-2023 Explorer/Aviator 4x4/AWD vehicles with hybrid powertrain may experience a harshness and/or vibration felt through the seat, steering wheel and/or center console after initial driveaway between 25-50 MPH (40-80 Km/h) that lessens after driving 5-10 minutes. This may be due to driveshaft center bearing bounce mode during cold ambient temperatures. To resolve the concern, install a softer durometer L1MZ-4A499-F driveshaft center bearing per Workshop Manual Section 205-01. For claiming, use causal part 4A499 and applicable labor operations in Section 4 of the Service Labor Time Standards (SLTS) Manual.
SSM 514192023-04-04. Service bulletin. POWER TRAIN. Some 2017-2023 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability.
TSB 23-20792023-04-04. Service bulletin. EQUIPMENT. Some 2022-2023 Explorer vehicles may exhibit a buzz/vibration/rattle from the center left of the IP during tip-in when the vehicle is up to operating temperature. This may be due to heater tube movement against the tube bracket.
TSB 22-24112023-04-04. Service bulletin. POWER TRAIN. Some 2022 Explorer/Aviator/Bronco vehicles built on or before 9-Aug-2022 and equipped with a 10R60 automatic transmission may exhibit a harsh 7-6 gear downshift. This may be caused by the A clutch piston return spring snap ring becoming dislodged. To correct the condition, follow the Service Procedure to replace the front support assembly and A clutch components.
TSB 22-24062023-04-04. Service bulletin. POWER TRAIN. Some 2021-2023 Explorer Timberline vehicles may exhibit differential fluid venting from the differential fluid vent. The customer may notice differential fluid pooling below the vehicle or saturating the wheel well liner. This may be due to the differential vent tube not having enough positive incline. To correct the condition, follow the Service Procedure to replace the differential vent tube.
23B012023-03-06. Service bulletin. ENGINE AND ENGINE COOLING. Certain 2021-2022 Model Year Various Vehicle Lines Long Block Replacement
SSM 513922023-03-04. Service bulletin. EQUIPMENT. Some vehicles equipped with a 2.7L, 3.0L,3.5L or 5.0L engine may require replacement of the long block engine assembly. New service kits have been released which include all the one-time-use components required in the service procedure for removal and replacement of the long block engine assembly. Refer to the Ford Electronic Parts Catalog (ECAT) for long block service kit part number by application.
SSM 513802023-03-04. Service bulletin. ELECTRICAL SYSTEM. Some 2020-2023 Explorer/Aviator vehicles may exhibit the A/C blowing warm air with DTCs P0645, P2CFC, and/or P2CFD present in the heating ventilation and air conditioning (HVAC) module. This may be due to spread terminal/terminal pushout in wire harness 14290 and on the corresponding pins to the body control module C (BCMC). Before replacement of the BCMC, disconnect all connectors from the BCMC and check the BCMC pins and wire terminals for damage. Refer to Workshop Manual (WSM), Section 419-10. If spread terminals or terminal pushout is present, repair as necessary. Refer to Wiring Diagram, Cell 005 for repair procedures. Reconnect all connections to the BCMC as indicated by the procedure in the WSM. Test the function of the A/C to verify that it is blowing cold air.
SSM 513332023-03-04. Service bulletin. ENGINE AND ENGINE COOLING. Some 2022-2023 Explorer vehicles equipped with a 2.3L engine may exhibit an intermittent check engine light on with diagnostic trouble code (DTC) P1026 and/or P1299 present in the powertrain control module (PCM) and an engine over-temperature message displayed on the instrument panel cluster (IPC) after a cold start in cold (at or below freezing) ambient temperatures. The vehicle may also enter fail safe cooling open loop mode when this concern occurs. If the engine does not show any obvious signs of overheating and Workshop Manual, Section 303-03A diagnostics are inconclusive, clear the DTCs to reset the fail safe cooling open loop mode. Inform the customer that Ford is currently investigating this concern and that they can continue to drive the vehicle. Monitor OASIS for further updates.
SSM 513062023-02-02. Service bulletin. ELECTRICAL SYSTEM. Some 2018-2023 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150 - G401, Expedition/Navigator - G403, Transit - G401, 2018-2019 Explorer G302, 2020-2022 Explorer/Aviator - G407) and confirm FPCM connector (F-150 - C4336, Expedition/Navigator - C433, Transit - C433, 2018-2019 Explorer - C3239, 2020-2022 Explorer/Aviator - C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.
SSM 512972023-01-31. Service bulletin. POWER TRAIN. Some 2020-2023 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a hybrid powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2D40. This may be due to the high voltage battery thermal system not cooling as it should. Follow the updated WSM Section 414-03 including listed possible sources, visual inspection and prechecks, and diagnostic procedures.
TSB 23-20302023-01-31. Service bulletin. POWER TRAIN. 2020-2022 Aviator/Explorer/Police Interceptor, 2021-2022 F-150 vehicles equipped with a 10R80 MHT transmission and built on or before 15-Nov-2022 may exhibit an 8th gear start after coming to a stop and/or a no movement in Reverse condition. This may be due to the driver applying the accelerator pedal and brake pedal simultaneously during regenerative braking. To improve the condition, follow the Service Procedure to reprogram the powertrain control module (PCM) and refer the customer to the Automatic Transmission Section of the Owners Manual warning regarding applying both pedals simultaneously.
SSM 512652023-01-06. Service bulletin. VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR; EQUIPMENT. Some vehicles equipped with power folding mirrors may exhibit power folding mirrors that are inoperative or exhibit a clicking sound. This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.
SSM 512612023-01-06. Service bulletin. SERVICE BRAKES. Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 512472023-01-05. Service bulletin. ELECTRICAL SYSTEM. Some 2020-2022 Explorer vehicles equipped with a 2.3L engine may exhibit an illuminated malfunction indicator lamp (MIL) with multiple diagnostic trouble codes (DTCs). These DTCs may include P04F0, P008A, P0451, P0455, P0456, P0496 and/or P018C. This may be due to the wiring harness connection at connector C1198 on driver's side lower frame area underneath the brake lines that route near the electric brake booster (EBB). Prior to replacement of any components, inspect the connector and wiring harness for any damage or pin fit concerns. If any damage or pin fit concerns are found, repair the connector or harness as necessary. If no damage or pin fit concerns are found, refer to normal diagnostics. Refer to Wiring Diagram (WD) Cell 22-12 to view the 3 voltage reference (VREF) wires at C1198 on the 2.3L engine.
SSM 512282023-01-05. Service bulletin. COMMUNICATION:MANUFACTURER TELEMATICS. Some 2020-2023 Ford and Lincoln vehicles equipped with a telematic control unit (TCU) may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 22-24852023-01-05. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL:WIRELESS CHARGER/CRADLE. Some 2020-2021 Expedition/Navigator, 2020-2022 F Super Duty/Explorer, 2021-2022 Bronco/Corsair/Escape/Bronco Sport, 2022 Maverick vehicles may exhibit the wireless charger inoperative or poor performance when using some Apple iPhone models that use MagSafe wireless charging including iPhone 12 and 13. This may be due to limited compatibility with the wireless accessory charging module (WACM). To correct the condition, follow the Service Procedure to update the WACM. Note: The WACM software is designed to improve the compatibility between some Apple MagSafe charging iPhones, including iPhone 12 and 13 models, and the Ford Qi wireless charging module.
TSB 22-24332023-01-05. Service bulletin. FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY. This article supersedes TSB 22-2176 to increase the labor operation allowance and update the part list. Some 2020-2022 Escape/Corsair vehicles built on or before 3-Jan-2022, 2020-2022 Explorer vehicles built on or before 14-Feb-2022, 2020-2022 Aviator vehicles built on or before 07-Feb-2022 and 2021-2022 Bronco Sport vehicles built on or before 3-Dec-2021 may exhibit a slow fuel fill and/or spit back condition during refueling. This may be due to the design of the fuel tank filler pipe. To correct the condition, follow the Service Procedure to replace the fuel tank filler pipe.
22G012022-12-02. Service bulletin. UNKNOWN OR OTHER. Certain 2022 Model Year Explorer Vehicles Rear Climate Control Module Retrofit In all of the affected vehicles, a global supply shortage of semiconductor chips caused unavailability of the rear heating, ventilation and air conditioning control (RHVAC) module for certain vehicles.
SSM 511692022-11-29. Service bulletin. BACK OVER PREVENTION:DISPLAY FUNCTION. Some 2020-2022 Aviator/Explorer Hybrid vehicles may experience a concern where the EV power flow does not display in the center display screen. This may be due to accessory protocol interface module (APIM) software. To correct the condition, run the APIM-SYNC Module (APIM) Standard Programming application using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 22-23772022-10-31. Service bulletin. ENGINE AND ENGINE COOLING. Some 2020-2022 Explorer/Aviator vehicles equipped with a 3.0L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure to replace the VCT units.
SSM 511322022-10-19. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:WIRING. Some 2020-2022 Explorer vehicles equipped with a 2.3L engine may exhibit an illuminated malfunction indicator lamp (MIL) with multiple diagnostic trouble codes (DTCs). These DTCs may include P04F0, P008A, P0451, P0455, P0456, P0496 and/or P018C. This may be due to the wiring harness connection at connector C1198. Prior to replacement of any components, inspect the connector and wiring harness for any damage or pin fit concerns. If any damage or pin fit concerns are found, repair the connector or harness as necessary. If no damage or pin fit concerns are found, refer to normal diagnostics.
SSM 511312022-10-19. Service bulletin. UNKNOWN OR OTHER; COMMUNICATION:MANUFACTURER TELEMATICS. Some 2020-2022 Ford and Lincoln vehicles equipped with a telematic control unit (TCU) may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 511202022-10-11. Service bulletin. SERVICE BRAKES, HYDRAULIC. Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.