WenmarOpen by Wenmar Pro

Service bulletins for the 2021 Ford Explorer

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

326 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Brakes are shown. Show all

Bulletins, newest first
TSB 23-21202023-05-23. Service bulletin. PARKING BRAKE; POWER TRAIN. Some 2018-2021 Expedition/Navigator and 2020-2021 Explorer/Aviator vehicles equipped with a 10R80/10R80 MHT or 10R60 may exhibit a momentary transmission neutral-out condition while in drive. Vehicle may also have diagnostic trouble code (DTC) P07E6 and/or P07E4 stored in the powertrain control module (PCM) or transmission control module (TCM) and/or a possible audible noise. This may be due to a leak in the park valve circuit. To correct the condition, follow the Service Procedure to inspect the park system hardware for wear or damage and replace the valve body separator plate with an improved valve body separator plate.
SSM 513742023-03-04. Service bulletin. POWER TRAIN; SERVICE BRAKES. Some 2020-2021 Escape/Bronco Sport/Explorer and 2020-2021 Corsair/Aviator vehicles equipped with electric brake booster (EBB) built on or before 1-Aug-2022 may exhibit an illuminated anti-lock brake system (ABS) warning indicator and stability-traction control warning indicator with diagnostic trouble code (DTC) U3000:96 erroneously stored in the ABS module. This condition occurs during connection or power interrupt to the EBB module. If this code is stored and the ABS system has been reassembled, clear the DTC code using Ford Diagnosis and Repair System (FDRS) scan tool and check for recurrence. If the DTC persists, perform normal diagnostics. Refer to the Workshop Manual (WSM), Section 206-09 Anti-Lock Brake System. For claiming use the causal part number 2C219 and applicable labor operations in Section 2 of the Service Labor Time Standards.
SSM 512612023-01-06. Service bulletin. SERVICE BRAKES. Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 511202022-10-11. Service bulletin. SERVICE BRAKES, HYDRAULIC. Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 504722022-02-16. Service bulletin. SERVICE BRAKES, HYDRAULIC:POWER ASSIST:VACUUM:HOSES, LINES/PIPING, AND FITTINGS; SERVICE BRAKES, HYDRAULIC. Some 2021-2022 Bronco vehicles equipped with the 2.3L engine may exhibit a red brake warning lamp and/or brake system warning message in the instrument panel cluster (IPC) with a diagnostic trouble code (DTC) P050F in the anti-lock brake system (ABS) module and a firm brake pedal. This may be due to contamination in a brake booster vacuum line. To correct this condition, replace the vehicle's vacuum hose (MB3Z-2420-A). Refer to Workshop Manual (WSM), Section 206-09 for installation instructions. For claiming, use casual part 2420.
TSB 21-22932021-09-30. Service bulletin. SERVICE BRAKES, AIR:ANTILOCK:ABS WARNING LIGHT; EQUIPMENT; ELECTRICAL SYSTEM. Some 2020-2021 Explorer/Aviator hybrid vehicles may exhibit a brake pedal pulsation or vibration when the brakes are applied. The customer may state that the anti-locking brake system (ABS) system is activating without any indicators on the instrument panel cluster (IPC). This may be due to the regenerative braking software in the ABS module. To correct the condition, follow the Service Procedure Steps to perform a coordinated flash on the powertrain control module (PCM) and ABS module.
SSM 500642021-09-04. Service bulletin. SERVICE BRAKES, ELECTRIC:SOFTWARE/PROGRAMMING. Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
TSB 21-20302021-03-02. Service bulletin. ELECTRICAL SYSTEM; SERVICE BRAKES. Some 2020-2021 Explorer/Aviator/Police Interceptor Utility vehicles built on or before 24-Dec-2020 may exhibit an illuminated anti-lock brake system (ABS) warning indicator lamp with diagnostic trouble code (DTC) C0020 stored in the ABS module. It may not be necessary to replace the ABS module/hydraulic control unit (HCU) to resolve DTC C0020. This may be due to a poor ground connection and/or improper plating on the attachment bolts at G108. To correct the condition, follow the Service Procedure to replace and properly tighten the ground cable fasteners.
SSM 494332021-02-04. Service bulletin. EQUIPMENT; WHEELS; SERVICE BRAKES. Some 2020-2021 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit an illuminated anti-lock brake system (ABS) warning lamp with diagnostic trouble codes (DTCs) C0031, C0034, C0037, and/or C003A. This may be due to metal contamination on the wheel speed sensors or wheel speed sensor rings. Verify that all wheel speed sensors and wheel speed sensor rings are free of metal contamination before replacing them. Refer to Workshop Manual (WSM), Section 206-09 for diagnostics.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.