WenmarOpen by Wenmar Pro

Service bulletins for the 2016 Ford Explorer

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

212 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
SSM 477972019-04-08. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2009-2017 Expedition/Navigator, 2009-2014 F-150/Mustang, 2008-2009 Sable, 2008-2019 Taurus/Flex/MKT, 2013-2019 Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.
TSB 19-20502019-04-08. Service bulletin. VISIBILITY:POWER WINDOW DEVICES AND CONTROLS; ELECTRICAL SYSTEM. Some 2016-2017 Explorer vehicles may exhibit front window glass that jumps/chatters during up/down movement. This may be due to various conditions in the window motor including excessive drive gear backlash, bushing wear, and/or excessive endplay. To resolve the concern, replace the door glass top run, door glass, window regulator, window motor and wiring harness.
SSM 478992019-04-03. Service bulletin. ELECTRICAL SYSTEM. Some 2017-2019 F-Super Duty, 2017-2019 Continental, and 2016-2018 Explorer/Police Interceptor Utility vehicles may exhibit a crank/no start condition, inoperative trailer tow lighting and/or inoperative power telescoping mirrors. This may be due to a concern within the battery junction box (BJB) relay module. A lower level service part has been released to allow for replacement of just the BJB relay module instead of the BJB harness. F-Super Duty part number HU5Z-14A067-A, Continental part number GU5Z-14A067-C, Explorer part number FU5Z-14A067-A, Police Interceptor Utility part number GU5Z-14A067-B.
SSM 478792019-04-03. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM. Various 2019 vehicles equipped with SYNC 3 and the latest software version 3.2 may exhibit an error message when attempting to update the software to version 3.3. Professional Technician Society (PTS) website may show that software version 3.3 is available for 2019 SYNC 3 vehicles. Do not carry out this update as it may lead to a hardware error message. Engineering is investigating, monitor OASIS for updates.
SSM 478242019-04-01. Service bulletin. ELECTRICAL SYSTEM. Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 477972019-04-01. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ELECTRICAL SYSTEM. Some 2009-2017 Expedition/Navigator, 2009-2014 F-150/Mustang, 2008-2009 Sable, 2008-2019 Taurus/Flex/MKT, 2013-2019 Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.
SSM 477112019-03-04. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
TSB 18-23672019-03-04. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2017 Explorer/Police Interceptor Utility vehicles equipped with a 3.5L EcoBoost engine built on or before 30-Sep-2016 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0325, P0327, P0330 and/or P0332. This may be caused by a wire chafe condition near the knock sensor connector C109. Follow the Service Procedure steps to correct the condition.
SSM 476352019-01-07. Service bulletin. ELECTRICAL SYSTEM. When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
SSM 475382018-12-03. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the Android Auto Preference menu selection is not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.
SSM 475702018-11-19. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2016-2018 Explorer vehicles built on or before 07-Aug-2018 may automatically switch from A/C to heat and defrost after 1 minute during a remote start event when the customer expects the A/C to remain on. To resolve the concern, reprogram the heating, ventilation and air conditioning (HVAC) control module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 19980 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 475002018-09-24. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some 2015-2017 Explorer and Police Interceptor Utility vehicles equipped with 3.5L Ecoboost engines may exhibit a surge or hesitation condition at approximately 50-60 MPH in 6th gear under light to moderate loads. If there are no DTCs stored in the powertrain control module (PCM), do not attempt further repairs. Advise customers this is a normal characteristic of the vehicle and will not affect durability of the engine or transmission.
SSM 474442018-09-24. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 473932018-07-23. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Some 2016-2018 Explorer vehicles may automatically switch from A/C to heat and defrost after 1 minute during a remote start idle when the customer expects the A/C remain on. The system will return to normal operation after the ignition is turned to the run position. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. To assist with the investigation, use the Report A Vehicle Concern link at the bottom of the OASIS report to complete the form.
SSM 473792018-07-23. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 473502018-07-23. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. RKE stand alone key fobs can be added to 2016 and newer Police Utility vehicles not previously equipped with them. To program the fobs, start an IDS session and enter the Red Toolbox > Module Programming > Programmable Parameters > Police Mode > Remote Keyfob Learn > Enable. Next, refer to the RKE Transmitter Programming procedure listed in Workshop Manual (WSM), Section 501-14 > General Procedures to program the fobs. If the RKE fobs fail to program, verify that the fobs are the correct part number. If the fobs are correct for the vehicle, then refer to the inoperative key fob diagnostics outlined in WSM, Section 501-14. This procedure and part numbers do not apply to 2015 and previous model year Police Utility vehicles. Blue lift gate button fobs are part No. GB5Z-15K601-C and red panic button fobs are part No. GB5Z-15K601-A.
SSM 470412018-06-11. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM. Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 472112018-05-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 471672018-05-21. Service bulletin. ELECTRICAL SYSTEM. Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 471632018-05-21. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Some 2016-2018 Explorer vehicles equipped with automatic temperature control and premium AM/FM/CD may exhibit a broken or missing temperature control switch. The driver and passenger switches are now available separately from the control head. Replacement of the control head assembly is not necessary. The switches are driver and passenger specific and must be installed in the correct location with the red heat indicator facing up. HB5Z-19986-AA - Drivers Side Switch, HB5Z-19986-BA - Passengers Side Switch
SSM 470702018-05-14. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start or no crank conditions or the IPC inoperative. For Lincoln vehicles, this information is now listed in the Technical Inspection and Post Road Test Sections of ePDI on the PTS website. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
SSM 469002018-01-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
SSM 468582017-12-14. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2017 Police Interceptor Utility vehicles may exhibit flickering front amber marker lamps (inboard amber lights under the headlamps) when the engine is running. Before attempting repairs, verify the frequency type using the Integrated Diagnostic System (IDS) or equivalent. The frequency type in police mode programmable parameters must be set to type 2. The engine must be running for the configuration to complete if this parameter is changed.
SSM 464652017-08-01. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM. Some 2016 Edge/Explorer/F-150/Mustang built on or before 01-Nov-2016 and equipped with a 4.2-inch FCDIM may exhibit a blank screen. To correct the concern, Reprogram the FCDIM to the latest level using IDS release 104.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 10D885 and applicable labor operations in section 10 of the service labor time standards (SLTS) manual.
SSM 463672017-03-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. SOME 2016 EDGE, F150, EXPLORER, AND MUSTANG VEHICLES EQUIPPED WITH A MYFORD DISPLAY 4 INCH SCREEN MAY EXHIBIT A BLANK SCREEN AND NO AUDIO. REPROGRAM THE FRONT CONTROL DISPLAY INTERFACE MODULE (FCDIM) TO THE LATEST CALIBRATION USING INTEGRATED DIAGNOSTIC SYSTEM (IDS) RELEASE 104.01 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. USE CAUSAL PART NUMBER 10D885 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.