WenmarOpen by Wenmar Pro

Service bulletins for the 2018 Ford Expedition

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

165 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
TSB 20-22672020-10-01. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM:ADAS:DRIVER MONITORING:CAMERA/SENSOR. Some 2015-2020 F-150 except Raptor, 2017-2020 F-Super Duty, 2018-2020 Expedition vehicles equipped with a front camera washer may exhibit a washer fluid leak at the front camera washer jet when not in use. This may be due to the rubber seal internal to the jet. To correct the condition, follow the Service Procedure to replace the washer jet.
SSM 490842020-09-04. Service bulletin. ELECTRICAL SYSTEM. Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app , incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 20-22552020-09-02. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F150/Focus/CMAX/Edge/Fiesta/MKX/ Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
TSB 20-22532020-09-02. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; POWER TRAIN. Some 2018-2020 Expedition/Navigator two-wheel drive (2WD) vehicles may exhibit a clunk noise from the driveshaft area when shifting from REVERSE to DRIVE or DRIVE to REVERSE and/or during coast down. This condition may be caused by a slip/stick condition at the transmission output flange/anti-ting ring interface. To correct the condition, follow the Service Procedure to apply a light coating of grease to the anti-ting washer and output shaft splines.
TSB 20-22332020-08-06. Service bulletin. STRUCTURE. This article supersedes TSB 19-2026 to update the vehicle model years affected. Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.
SSM 490012020-08-04. Service bulletin. ELECTRICAL SYSTEM. Some 2018-2019 Explorer/Expedition/F-150/F-Super Duty/Taurus vehicles equipped with a forward collision warning head up display (HUD) may exhibit various warning indicators caused by a possible intermittent lack of HS2-CAN (HS-CAN for Taurus) network communication. If the concern cannot be duplicated, place the vehicle in direct sunlight for 15 to 30 minutes to increase the temperature of the HUD and retest. If the concern is present, disconnect the HUD and check for proper network communication. If proper network communication is achieved, then HUD module replacement is likely needed. If disconnecting the HUD does not re-establish communication, the HUD is not at fault, refer to Workshop Manual (WSM), Section 418-00 for diagnostics.
TSB 20-21662020-07-08. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING; EQUIPMENT ADAPTIVE/MOBILITY. Some 2018-2019 Expedition/Navigator vehicles built on or before 8-Apr-2019 equipped with a 3.5L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure steps to replace the VCT units and update the powertrain control module (PCM) calibration with revised VCT parameters.
SSM 489082020-07-07. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Some 2016-2020 Ford and Lincoln vehicles equipped with a SYNC 3 Touchscreen may experience the volume control unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.
SSM 489342020-07-07. Service bulletin. FORWARD COLLISION AVOIDANCE: WARNINGS. Some 2018-2019 Explorer/Expedition/F-150/F-Super Duty/Taurus vehicles equipped with a forward collision warning head up display (HUD) may exhibit various warning indicators caused by a possible intermittent lack of HS2-CAN network communication. If the concern cannot be duplicated, place the vehicle in direct sunlight for 15 to 30 minutes to increase the temperature of the HUD and retest. If the concern is present, disconnect the HUD and check for proper HS2-CAN network communication. If proper HS2-CAN network communication is achieved, then HUD module replacement is likely needed. If disconnecting the HUD does not re-establish communication, the HUD is not at fault, refer to Workshop Manual (WSM), Section 418-00, PPT AL for diagnostics.
TSB 20-21892020-07-06. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; VEHICLE SPEED CONTROL:ACCELERATOR PEDAL; EQUIPMENT. This article supersedes TSB 20-2028 to update the description of Labor Operation D. Some 2013-2018 F-150/Expedition/Navigator vehicles equipped with 4-wheel drive (4WD) may exhibit an intermittent grinding noise while driving in 2-wheel drive (2WD) mode most commonly on acceleration. This may be due to a loss of vacuum to the integrated wheel end (IWE) actuators and/or wear of the IWE components. To correct the condition, follow the Service Procedure steps to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.
TSB 20-21712020-06-05. Service bulletin. STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS; SEATS. Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
TSB 20-21702020-06-05. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2018-2020 F-150/Expedition/Navigator/F-Super Duty vehicles built on 31-Aug-2018 and through 02-Feb-2020 may exhibit a water leak on the right front floor during and/or after the air conditioning (A/C) is used. This may be due to condensation from the evaporator drain tube entering the vehicle through the drain tube seal. To correct the condition, follow the Service Procedure steps to install an elbow on the evaporator drain tube to direct the condensation away from the seal.
SSM 488582020-06-04. Service bulletin. ELECTRICAL SYSTEM. Some 2012-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit an inoperative remote start with a 'Vehicle Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.
SSM 488072020-06-04. Service bulletin. FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM; ENGINE AND ENGINE COOLING. Some 2017-2020 Model year vehicles equipped with 3.3L, 3.5L EcoBoost, or 5.0L engines may exhibit stalling, lack of power, low fuel rail pressure and/or DTCs P0087 or P008A after a repair was made that required the removal of the fuel line that connects the high-pressure fuel pump to the port injection rail, such as injector replacements or base engine repairs. This line must be installed in the correct orientation as it has an internal one-way check valve. To determine if the fuel line has been installed improperly, look at the position of the Oetiker clamp (stainless band clamped around the black fuel line). The clamp holds the one-way check valve in place and should be located closest to the end connected to the port injection rail. If the clamp is not closest to the port injection rail, remove and reinstall the line in the proper orientation.
TSB 20-21322020-06-04. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). This article supersedes TSB 19-2232 to update the vehicles affected. Some 2017-2019 F-150 and 2018-2019 Expedition vehicles built on or before 1-Apr-2019 and equipped with a 3.5L EcoBoost engine may exhibit excessive oil consumption with no visible oil leaks with or without diagnostic trouble code (DTC) P0365 and/or P0369. This may be due to a concern with the positive crankcase ventilation (PCV) system. To correct the condition, follow the Service Procedure steps to verify the condition and replace the valve covers.
TSB 20-21172020-05-05. Service bulletin. POWER TRAIN. Some 2017-2018 F-150/Raptor, 2018 Expedition/Mustang/Navigator vehicles equipped with a 10R80 automatic transmission and built on or before 20-Nov-2017 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0741 and P1744 in the powertrain control module (PCM) or transmission control module (TCM). This may be due to a sticking torque converter clutch (TCC) valve in the main control valve body assembly. To correct the condition, follow the Service Procedure to replace the main control valve body.
TSB 20-20512020-03-03. Service bulletin. EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK ASSEMBLY. Some 2017-2018 F-150 vehicles equipped with a 3.5L EcoBoost engine built at Kansas City Assembly Plant on or before 23-Feb-2018 or Dearborn Truck Plant on or before 26-Feb-2018 and Expedition/Navigator vehicles built on or before 19-Mar-2018 may exhibit an oil leak from the oil pan RTV seal. This may be due to a lack of RTV adhesion. This article includes detailed steps to achieve proper RTV adhesion. To correct the condition, follow the Service Procedure steps to replace the oil pan.
TSB-20-20282020-03-03. Service bulletin. SERVICE BRAKES, HYDRAULIC:POWER ASSIST:VACUUM; EQUIPMENT. Some 2013-2018 F-150/Expedition/Navigator vehicles equipped with 4-wheel drive (4WD) may exhibit an intermittent grinding noise while driving in 2-wheel drive (2WD) mode most commonly on acceleration. This may be due to a loss of vacuum to the integrated wheel end (IWE) actuators and/or wear of the IWE components. To correct the condition, follow the Service Procedure steps to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.
TSB 20-20152020-02-04. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2018 F-150 vehicles equipped with a 3.5L EcoBoost engine built at Kansas City Assembly Plant on or before 23-Feb-2018 or Dearborn Truck Plant on or before 26-Feb-2018 and Expedition/Navigator vehicles built on or before 19-Mar-2018 may exhibit an oil leak from the oil pan RTV seal. This may be due to a lack of RTV adhesion. This article includes detailed steps to achieve proper RTV adhesion. To correct the condition, follow the Service Procedure steps to replace the oil pan.
TSB19-23742020-01-07. Service bulletin. STRUCTURE. Some 2015-2019 F-150, 2017-2019 F-Super Duty, 2018-2019 Expedition/Navigator vehicles may exhibit a rattle and/or squeak noise from the vista roof opening panel while driving with the roof opening panel closed. This may be due to dirt and/or debris build up between the vista roof opening panel seal and the body. To correct the condition, follow the Service Procedure steps to clean and lubricate the vista roof opening panel seal.
TSB 19-23452019-12-04. Service bulletin. STRUCTURE. Some 2018-2020 F-150/Expedition/Navigator/F-Super Duty vehicles may exhibit a water leak on the right front floor during or after the air conditioning (A/C) is used. This may be due to condensation from the evaporator drain tube entering the vehicle through the drain tube seal. To correct the condition, follow the Service Procedure steps to install an elbow on the evaporator drain tube to direct condensation away from the seal.
SSM 482722019-11-05. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Some 2017-2018 F-150s built on or before 10-Jul-2018 and 2018-2019 Expedition and Navigator built on or before 8-Apr-2019 with 3.5L EcoBoost may exhibit tick, tap, or rattle type noises from top of engine front cover for 2-5 seconds after a cold start. A TSB is expected to be published late 4th quarter 2019. In the interim, replace all 4 VCT units and update the PCM calibration. Do not replace other cam drive related components unless inspection identifies a concern. Refer to the Workshop Manual (WSM), Section 303-01. Claim labor replace VCTs using published labor operations and PCM programming using M-time. Part availability is currently limited. Dealers should order parts only when required to complete a repair. Once the parts are ordered, the vehicle may be returned to the customer to drive. This condition does not affect long term durability or performance.
SSM 481682019-10-04. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2018 F-150 vehicles built on or before 10-Jul-2018 and 2018-2019 Expedition/Navigator vehicles built on or before 8-Apr-2019 equipped with a 3.5L EcoBoost engine may exhibit a ticking, tapping, or rattle type noise from the top front cover area of the engine that last 2-5 seconds on initial start-up after a cold soak. This may be due to a worn variable cam timing (VCT) unit. A TSB is expected to be published 4th quarter of 2019. In the interim, replace all 4 VCT units and update the powertrain control module (PCM) calibration. Do not replace timing chains, tensioners, guides or other timing related components unless inspection clearly identifies a concern. Refer to the Workshop Manual (WSM), Section 303-01. Claim the labor required to replace VCTs using published labor operations and PCM programming using M-time. Monitor OASIS for updates.
SSM 481082019-08-07. Service bulletin. ELECTRICAL SYSTEM. Some 2015-2019 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the appropriate Ford diagnostic scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the body control module (BCM) is internally damaged and requires replacement. The BCM should only be replaced for this condition when the 232 key table error message is present. If the 232 key table error is not present, follow normal diagnostics for the no crank condition. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 480822019-08-07. Service bulletin. POWER TRAIN. Some 2015-2018 F-150/Expedition/Navigator vehicles equipped with a 3.5L/2.7L EcoBoost engine and four-wheel drive (4WD) may exhibit an intermittent grinding type noise while driving in two-wheel drive (2WD), most commonly on acceleration. This noise could appear to be turbocharger related. After engineering analysis of returned turbochargers that have been replaced for this condition, no concerns were identified with the turbochargers. The grinding type noise may be related to the 4WD system integrated wheel ends (IWE). To aid in diagnosis, shift the vehicle to 4WD and attempt to verify the condition. If the grinding noise no longer occurs with the vehicle in 4WD a IWE vacuum system and/or mechanical fault may be present.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.