WenmarOpen by Wenmar Pro

Service bulletins for the 2024 Ford Escape

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

163 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
SSM 524102024-04-24. Service bulletin. UNKNOWN OR OTHER. Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.
SSM 523692024-04-04. Service bulletin. ENGINE AND ENGINE COOLING. 2024 Escape/Bronco Sport vehicles equipped with 1.5L engines should not be taken out of transport mode before customer delivery to reduce the risk of various driving performance concerns such as: rough operation, idle quality, engine misfires, lack or loss of engine power. These conditions may occur due to carbon fouled spark plugs from repeated engine ignition starts without driving the vehicle to normal operation temperatures 179°F-206°F (82°C-97°C) during cold weather. Make sure that the vehicles in stock are in transport mode before customer delivery. Refer to the Workshop Manual (WSM), Section 419-10 Malfunction Electronic Modules > General Procedures.
SSM 523682024-04-04. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. 2024 Escape and Bronco Sport vehicles equipped with 1.5L engines should add local fuel once the vehicle arrives at the dealership to reduce the risk of various engine performance concerns such as: rough operation, idle quality, engine misfires, lack or loss of engine power. These conditions may occur due to different fuel specifications between the manufacturing plant and the final market. Make sure that the vehicles in stock have local fuel added.
TSB 24-20782024-04-03. Service bulletin. POWER TRAIN. This article supersedes TSB 23-2244 to add 2024 model year. Some 2020-2024 Escape hybrid vehicles equipped with a 2.5L (FHEV) full hybrid electric vehicle powertrain and 4-wheel drive (4WD) may exhibit a grinding or rubbing noise while braking at or below 10 mph (16 km/h) from the front of the vehicle. This may be due to an inadequate gap between the driveshaft and the heat shield. To correct this condition, follow the Service Procedure to diagnose and position the heat shield away from the driveshaft.
SSM 523452024-03-20. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some 2022-2024 various Ford/Lincoln vehicles equipped with SYNC 4 may experience concern where customers are receiving an error message when trying to enroll in connected services. This may be due to the gateway module (GWM) software. To correct the concern, download and run the Transport and Factory Mode Deactivation app: under HS1 modules select BCM > Transport and Factory Mode > Download > Run. When the pop-up message appears for Change Vehicle Mode - Transport/Factory/Normal Mode, press OK. This will proceed to the Transport and Factory Mode Deactivation screen, select Unlock Vehicle Connectivity Settings (21 MY + Vehicles). A pop-up message appears noting Vehicle Is Now In Normal Mode, select OK. This will return to the Transport and Factory Mode Deactivation screen, select Exit. A final pop-up notification stating that the application is finished, select OK. For claiming, use causal part 14G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 523352024-03-20. Service bulletin. ENGINE AND ENGINE COOLING. For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 523282024-03-20. Service bulletin. EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE; EQUIPMENT:ELECTRICAL:INFOTAINMENT. Some 2021-2024 Bronco/F-150, 2023-2024 Escape/F-Super Duty vehicles equipped with SYNC 4 may experience a concern during accessory protocol interface module (APIM) programming where the vehicle's center display screen indicates USB Error. This may be due to a lack of memory space available to perform the APIM software update. If it is a memory concern, the Ford Diagnosis and Repair System (FDRS) will provide an option to delete the voice application. Re-enter the module programming and when prompted, do not select first option - SYNC Module (APIM) Software Update, select the second option - Delete Voice Application(s) From Module. Once deleted, run the SYNC Module (APIM) Software Update as directed, this will update the software and automatically reload the voice app. If the voice delete option is not available, continue with normal diagnostics in the Workshop Manual, Section 418.
SSM 523142024-03-20. Service bulletin. POWER TRAIN. During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
OTAPU0102SVDFXEs2024-03-07. Service bulletin. BACK OVER PREVENTION:SOFTWARE; ELECTRICAL SYSTEM. Software Update 24-PU0102-SVD-FX for 2024 MY Escape vehicles is now available. Quality Improvements include: - Improved OTA deployment
SSM 522692024-02-23. Service bulletin. STRUCTURE:BODY:HATCHBACK/LIFTGATE; EQUIPMENT. 2022-2024 Explorer/Aviator vehicles built on or after 28-May-2022, 2022-2024 Expedition/Navigator vehicles built on or after 08-Jun-2022, 2022-2024 Escape vehicles built on or after 01-Jun-2022 and 2022 Corsair vehicles built on or after 01-Jun-2022 are no longer equipped with a hands free liftgate system. The vehicle is not misbuilt. The addition of any parts is not a warrantable repair. Do not submit a claim for this condition.
SANVol 2 Issue 12024-02-06. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN; ELECTRICAL SYSTEM. The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This artile includes ifnormation on warranty, technical service tips and other service information.
SSM 522192024-02-06. Service bulletin. ENGINE AND ENGINE COOLING. Some 2023-2024 Escape vehicles built on or before 11-Jan-2024 equipped with 1.5L engines may exhibit an Engine Coolant Over-Temperature Warning message displayed in the IPC and an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern can not be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Disconnect the charge air cooler inlet and outlet hose, overflow hose, upper and lower hose of the radiator and position these components aside. Disconnect the inlet and outlet coolant hoses of the heater core and position these compone
SSM 521342023-12-19. Service bulletin. BACK OVER PREVENTION. Various 2021-2024 Ford and Lincoln vehicles equipped with the rear camera on demand feature may exhibit a Please Check Surroundings For Safety or Full View Not Available message when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.