Service bulletins for the 2022 Ford Escape
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
169 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| TSB 23-2041 | 2023-03-04. Service bulletin. SERVICE BRAKES; POWER TRAIN. Some 2020-2022 Escape vehicles built on 1-Nov-2020 and through 29-Aug-2022 and 2021-2022 Bronco Sport vehicles built on or before 23-Sep-2022 may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity. This may be due to the suspension sensitivity of the vehicle and interaction of the caliper housing with the pad backplate. To correct this condition, follow the Service Procedure to replace the rear caliper bushings. |
|---|---|
| 22B38 | 2023-02-03. Service bulletin. POWER TRAIN. Certain 2022 Model Year Multiple Vehicle Lines Equipped with 8F35 Transmissions Transmission Replacement In all of the affected vehicles, the snap ring that is used to hold the 8F35 transmission clutch compression spring engaged was not fully seated in the assembly process. When the snap ring is not fully seated, the transmission will function as if the C clutch is partially engaged. The customer may experience rough shifts until the transmission can adapt to the clutch performance. There is a potential long term durability concern associated with the compromised function of the clutch. |
| SSM 51318 | 2023-02-02. Service bulletin. STRUCTURE; LATCHES/LOCKS/LINKAGES. Some 2020-2022 Escape/Corsair vehicles may exhibit a door ajar warning lamp or higher than expected efforts to fully close doors. Verify the hood/liftgate are not open. Confirm all doors are fully closed and latches are fully engaged. Doors will not fully close when lightly letting go of the door or letting it swing closed from a short distance under its own weight. Push/pull effort must be applied to doors while closing to fully engage latch and turn off the ajar signal warning. If doors are still not fully latching closed, manually adjust door striker position to allow for proper alignment and engagement to the door latch. The door hang position may also need to be slightly adjusted to achieve the same effect. Refer to Workshop Manual (WSM), Section 501-03. |
| SSM 51285 | 2023-01-31. Service bulletin. FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; VEHICLE SPEED CONTROL:CRUISE CONTROL. Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport, 2022 Maverick vehicles may exhibit any of the following driver assistance warning messages displayed in the instrument panel cluster (IPC): Pre-collision Assist Not Available, Cruise Control Not Available, Collision Warning Malfunction and/or Adaptive Cruise Control Malfunction. Diagnostic trouble code (DTC) U0415:00 may also be stored in the power steering control module (PSCM), DTC C0051:67 stored in the anti-lock brake system (ABS) module and DTC U0418:86 stored in the image processing module A (IPMA). This may be due to the software in the power steering control module (PSCM). To correct this condition, using the latest version of Ford Diagnosis and Repair System (FDRS) scan tool. Update the PSCM to the latest software level. |
| SSM 51261 | 2023-01-06. Service bulletin. SERVICE BRAKES. Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00. |
| SSM 51255 | 2023-01-05. Service bulletin. POWER TRAIN; STEERING:STEERING CONTROL MODULE. Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport, and 2022 Maverick vehicles may exhibit a hard, stiff, and/or difficult to turn condition due to a lack of power steering assist during engine start-up with various U3000 diagnostic trouble codes (DTCs) and/or U3000:66. To correct this condition, using the latest version of Ford Diagnosis and Repair System (FDRS) tool, select and run the PSCM - Reset the Power Steering Control Module (PSCM) application. After PSCM reset, perform an ignition cycle. Update the PSCM to the latest software level using (FDRS) tool. If DTCs U3000 returns, continue with diagnostics and repair direction using Workshop Manual (WSM), Section 211-02 > Power Steering > Diagnosis and Testing. For claiming, use causal part 3C529 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| SSM 51254 | 2023-01-05. Service bulletin. BACK OVER PREVENTION:SOFTWARE; ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR. Some 2020-2022 Escape/Corsair/F-53 Motorhome/F-59 Commercial Stripped Chassis, 2021-2023 F-650/F-750/E-Series, and 2021-2022 Bronco Sport vehicles may exhibit an intermittent no crank/no start condition and/or an intermittent blank instrument panel cluster (IPC)/SYNC touchscreen. This may be due to the software in the gateway module (GWM). To correct the condition, reprogram the GWM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part 14F642 and the applicable labor operations of Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| SSM 51228 | 2023-01-05. Service bulletin. COMMUNICATION:MANUFACTURER TELEMATICS. Some 2020-2023 Ford and Lincoln vehicles equipped with a telematic control unit (TCU) may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| TSB 22-2485 | 2023-01-05. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL:WIRELESS CHARGER/CRADLE. Some 2020-2021 Expedition/Navigator, 2020-2022 F Super Duty/Explorer, 2021-2022 Bronco/Corsair/Escape/Bronco Sport, 2022 Maverick vehicles may exhibit the wireless charger inoperative or poor performance when using some Apple iPhone models that use MagSafe wireless charging including iPhone 12 and 13. This may be due to limited compatibility with the wireless accessory charging module (WACM). To correct the condition, follow the Service Procedure to update the WACM. Note: The WACM software is designed to improve the compatibility between some Apple MagSafe charging iPhones, including iPhone 12 and 13 models, and the Ford Qi wireless charging module. |
| TSB 22-2433 | 2023-01-05. Service bulletin. FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY. This article supersedes TSB 22-2176 to increase the labor operation allowance and update the part list. Some 2020-2022 Escape/Corsair vehicles built on or before 3-Jan-2022, 2020-2022 Explorer vehicles built on or before 14-Feb-2022, 2020-2022 Aviator vehicles built on or before 07-Feb-2022 and 2021-2022 Bronco Sport vehicles built on or before 3-Dec-2021 may exhibit a slow fuel fill and/or spit back condition during refueling. This may be due to the design of the fuel tank filler pipe. To correct the condition, follow the Service Procedure to replace the fuel tank filler pipe. |
| SSM 51191 | 2022-11-30. Service bulletin. POWER TRAIN. Some 2021-2022 Mustang Mach-E built on or before 17-Jan-2022, 2022 Escape built on or before 03-Mar-2022, Bronco Sport built on or before 04-Mar-2022, 2022 Maverick built on or before 25-Jan-2022 and 2022 Transit built on or before 17-May-2022 may exhibit a powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0929:77 stored in the gear shift module (GSM). This may be due to the software in the GSM. To correct this condition, perform Pinpoint Test D. Refer to Workshop Manual (WSM), Section 307-05 > Diagnosis and Testing. If the GSM is not operating correctly, perform the replacement of the GSM. Do not perform a PMI after installing a new GSM assembly. The GSM is shipped with the latest software level. For claiming, use causal part 7P155 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| SSM 51184 | 2022-11-29. Service bulletin. PARKING BRAKE. Some 2020-2022 Escape/Corsair vehicles built on or before 17-May-2022 and 2021-2022 Bronco Sport vehicles built on or before 25-Feb-2022 may exhibit a hiss or rattle noise while driving. This may be due to an internal issue with the manual park release cable. If the noise is eliminated when the cable is disconnected from the transmission, install a new manual park release cable assembly LX6Z-7D246-T. Refer to the Workshop Manual (WSM), Section 307-05 > Automatic Transmission External Controls > Removal and Installation. |
| TSB 22-2387 | 2022-11-01. Service bulletin. ENGINE AND ENGINE COOLING. Some 2021-2022 Escape vehicles built on 01-Oct-2020 and through 21-Jul-2022 and equipped with 1.5L engine and vacuum booster and 2021-2022 Bronco Sport vehicles built on or before 2-Dec-2021 may exhibit a squeal noise from the front brakes when applied at low or high speed. The alternate front brake disc (standard version) improves high frequency noise performance. To correct this condition, follow the Service Procedure to perform the replacement of the front brake discs. |
| SSM 51149 | 2022-10-31. Service bulletin. ELECTRICAL SYSTEM. Some 2022 Escape vehicles built on 01-Dec-2021 and through 30-Jun-2022 equipped with one-touch open driver window may exhibit a condition where the passenger rear door window is inoperative. The vehicle may also exhibit a rear door window motor overheating. This may be due to a continuous power supply of the driver door master window switch. To correct this condition, replace the driver door master window switch. Refer to the Workshop Manual (WSM), Section 501-11 Glass, Frames and Mechanisms > Removal and Installation. Let the affected window regulator motor to cool down for 1-2 minutes before operating the switch again. For claiming, use causal part 14529 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. Note: The window regulator motor has thermal protection designed into the motor and will not be damaged |
| SSM 51137 | 2022-10-25. Service bulletin. POWER TRAIN. Some 2021-2022 Mustang Mach-E/Escape plug-in hybrid electric vehicle (PHEV), 2020-2022 Aviator PHEV, and 2022 Transit battery electric vehicle (BEV) vehicles may experience an illuminated powertrain malfunction (Wrench) indicator and/or malfunction indicator lamp (MIL) with secondary on board diagnostic control module (SOBDM) diagnostic trouble code (DTC) U3000:49. This may be due to an internal SOBDM concern. To correct the concern, replace the SOBDM following Workshop Manual, Section 414-03B Removal and Installation, Secondary On-board Diagnostic Control Module. For claiming use base part # 10B689 and the applicable labor operations of Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| SSM 51131 | 2022-10-19. Service bulletin. UNKNOWN OR OTHER; COMMUNICATION:MANUFACTURER TELEMATICS. Some 2020-2022 Ford and Lincoln vehicles equipped with a telematic control unit (TCU) may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| SSM 51120 | 2022-10-11. Service bulletin. SERVICE BRAKES, HYDRAULIC. Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00. |
| SSM 51117 | 2022-10-11. Service bulletin. POWER TRAIN. Some 2021-2022 Bronco Sport 1.5L, 2019-2022 Edge/Nautilus, 2020-2022 Escape/Corsair, and 2022 Maverick vehicles may exhibit an illuminated AWD warning indicator or fault message with diagnostic trouble code (DTC) C0095:71/:19 stored in the all wheel drive (AWD) module. Some 2021-2022 Bronco Sport 2.0L may exhibit an illuminated AWD warning indicator or fault message with DTC C05D9:71, C05E8:71, C05D8:19 and/or C05E7:19 stored in the AWD module. This may be due to a rear drive unit (RDU) motor magnet ring misalignment. RDU assembly replacement is no longer required. To correct the condition, replace the RDU motor which is now available separately for service. Refer to Workshop Manual, Section 205-02 for diagnosis and repair procedures. For claiming use causal part 4C210 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| TSB 22-2343 | 2022-09-30. Service bulletin. POWER TRAIN. Some 2021-2022 Mustang Mach-E vehicles built on 01-Aug-2021 and through 18-Jan-2022, 2022 Maverick vehicles built on 13-Sep-2021 and through 18-Jan-2022, 2022 Escape vehicles built on 24-Sep-2021 and through 18-Jan-2022, 2022 Bronco Sport vehicles built on 08-Nov-2021 and through 18-Jan-2022 may exhibit a shift knob can be rotated without stepping on the brake pedal, although the transmission remains in park (P). This condition may be intermittent, more noticeable in warmer temperatures. DTC P0929 may also be set in the gear shift module (GSM). This may be due to a GSM concern. To correct the condition, follow the Service Procedure to update the GSM. |
| SSM 51093 | 2022-09-26. Service bulletin. ENGINE AND ENGINE COOLING. Some 2022 Escape and Bronco Sport vehicles equipped with 1.5L engines should not be taken out of transport mode before customer delivery to reduce the risk of driving performance issues such as: rough operation, idle quality, engine misfires, lack or loss of engine power. These conditions may occur due to carbon fouled spark plugs from repeated engine ignition starts without driving the vehicle to normal operation temperatures (82°C to 97°C) during cold weather. Make sure that the vehicles in stock are in transport mode. Refer to the Workshop Manual (WSM), Section 419-10 Malfunction Electronic Modules > General Procedures. |
| SSM 51057 | 2022-09-01. Service bulletin. POWER TRAIN. Some 2021-2022 Mustang Mach-E, 2022 Escape/Bronco Sport/Maverick/Transit vehicles may exhibit a powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0929:77 stored in the gear shift module (GSM). This may be due to the software in the GSM. To correct this condition, reprogram the GSM module using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 7P155 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| TSB 22-2326 | 2022-08-23. Service bulletin. SUSPENSION. Some 2020-2022 Escape and 2022 Bronco Sport vehicles may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity. This may be due to the suspension sensitivity of the vehicle. To correct this condition, follow the Service Procedure to replace the rear caliper bushings. |
| SSM 51011 | 2022-08-15. Service bulletin. POWER TRAIN. Some 2018-2022 Ford and Lincoln vehicles equipped with the 8F35 transmission built on or before 16-Mar-2022 may exhibit transmission slip during acceleration from a stop when hot. This may be due damaged internal case half pump seals (7N265). To correct the condition, remove the transmission and replace the internal case half pump seals. Refer to Workshop Manual (WSM), Section 307-01. |
| SSM 50974 | 2022-08-02. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL; EQUIPMENT; ELECTRICAL SYSTEM:SOFTWARE. Some 2020-2022 Escape/Corsair/F-53 Motorhome/F-59 Commercial Stripped Chassis, 2021-2023 F-650/F-750/E-Series, and 2021-2022 Bronco Sport vehicles may exhibit a communication fault with emissions inspection equipment. This may be due to the software in the gateway module (GWM). To correct this condition, reprogram the GWM to latest software level using the appropriate Ford diagnostic scan tool. Use causal part 14F642 and applicable labor times from Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| TSB 22-2246 | 2022-07-01. Service bulletin. LATCHES/LOCKS/LINKAGES. Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport and 2022 Maverick vehicles may exhibit a condition where the door(s) do not open using the exterior door handle(s). This may be due to an enabled permanent engagement inertia lock within the exterior door handle, this condition occurs when the doors are closed or opened with excessive force. To correct this condition, follow the Service Procedure to properly disengage the permanent engagement inertia lock clip to allow the exterior door handle(s) to fully extend and open the door(s) from the outside. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.