Service bulletins for the 2004 Dodge Dakota
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
53 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Engine are shown. Show all
| 9003215 | 2023-01-09. Service bulletin. ENGINE AND ENGINE COOLING. Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine. |
|---|---|
| 05191925A | 2022-12-19. Service bulletin. ENGINE AND ENGINE COOLING. Radiator If vehicle comes in for transmission fluid leaking from trans-oil cooler fittings on the radiator, please perform the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Remove hex nut and the top flared fitting on the radiator tank.~ 3. Using a wire brush and gasket remover, clean off the old sealant on the smaller threaded portion of the flared fitting. Do the same for the threads on the trans oil cooler.~ 4. Apply a new application of Mopar PN 04318032 to the flared fitting, leaving the first threads free for ease of engagement.~ 5. Install the top flared fitting by hand, then torque the fitting to 235 +/- 15 Lb-In.~ 6. Install the hex nut and torque to 100 +/- 10 Lb-In.~ 7. Repeat steps 2-6 for bottom flared fitting.~ 8. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ |
| 68332810 | 2022-10-17. Service bulletin. ENGINE AND ENGINE COOLING. Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar® Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 N·m [21 ft. lbs.]. |
| 9003215 | 2022-10-17. Service bulletin. ENGINE AND ENGINE COOLING. Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine. |
| R2118796A | 2021-05-03. Service bulletin. ENGINE AND ENGINE COOLING. Valve Body. These may cause over drive cycling. |
| 05191925A$ | 2020-10-26. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING; POWER TRAIN. Radiator If vehicle comes in for transmission fluid leaking from trans-oil cooler fittings on the radiator, please perform the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Remove hex nut and the top flared fitting on the radiator tank.~ 3. Using a wire brush and gasket remover, clean off the old sealant on the smaller threaded portion of the flared fitting. Do the same for the threads on the trans oil cooler.~ 4. Apply a new application of Mopar PN 04318032 to the flared fitting, leaving the first threads free for ease of engagement.~ 5. Install the top flared fitting by hand, then torque the fitting to 235 +/- 15 Lb-In.~ 6. Install the hex nut and torque to 100 +/- 10 Lb-In.~ 7. Repeat steps 2-6 for bottom flared fitting.~ 8. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ |
| 2500108 | 2008-03-06. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). POSITIVE CRANKCASE VENTILATION (PCV) SYSTEM FREEZES IN EXTREME COLD AMBIENT TEMPERATURES -- INVOLVES INSTALLING REVISED PCV SYSTEM COMPONENTS. *NJ |
| 05002 | 2005-05-18. Service bulletin. ENGINE AND ENGINE COOLING. NEW WATER PUMP FOR 3.7L ENGINE - NO LONGER COMMON WITH 4.7L. ADVANCED SERVICE INFORMATION #05-002. *TT |
| 1801704 | 2004-05-18. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE. DRIVEABILITY AND OBD II MONITOR IMPROVEMENTS. FLASH. 3.7L. *TT |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.