WenmarOpen by Wenmar Pro

Service bulletins for the 2009 Dodge Challenger

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

46 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
S17090000102023-01-09. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
21020162022-12-19. Service bulletin. EQUIPMENT; BACK OVER PREVENTION; POWER TRAIN. Manual Transmission Shifter Noise This bulletin involves greasing or replacing the manual transmission rear shifter bushing. Customers may experience a clunk, squeak, or similar noise heard from center console area while shifting.
90040092022-09-26. Service bulletin. POWER TRAIN. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
18-021-132022-07-18. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Flash: Performance Derate Above 55 MPH Immediately After Start-Up When Accelerating At Wide Open Throttle This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience any of the following conditions: Performance derate above 55 MPH when accelerating at wide open throttle immediately following engine start-up.
18-021-132021-03-15. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING. Flash: Performance Derate Above 55 MPH Immediately After Start-Up When Accelerating At Wide Open Throttle This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience any of the following conditions: Performance derate above 55 MPH when accelerating at wide open throttle immediately following engine start-up.
21-020-162020-10-26. Service bulletin. POWER TRAIN; EQUIPMENT. Manual Transmission Shifter Noise This bulletin involves greasing or replacing the manual transmission rear shifter bushing. Customers may experience a clunk, squeak, or similar noise heard from center console area while shifting.
21-020-162018-06-18. Service bulletin. POWER TRAIN:MANUAL TRANSMISSION. Manual Transmission Shifter Noise This bulletin involves greasing or replacing the manual transmission rear shifter bushing. Customers may experience a clunk, squeak, or similar noise heard from center console area while shifting.
18-021-132018-05-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Performance Derate Above 55 MPH Immediately After Start-Up When Accelerating At Wide Open Throttle This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience any of the following conditions: Performance derate above 55 MPH when accelerating at wide open throttle immediately following engine start-up.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.