WenmarOpen by Wenmar Pro

Service bulletins for the 2011 Chevrolet Silverado

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

2185 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
1008110001I2021-05-03. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This informational bulletin provides information on proper use of floor mats.
100310001F2021-05-03. Service bulletin. WHEELS. This informational bulletin provides information on Wheel Balancer Mounting Instructions.
21NA0432021-05-03. Service bulletin. EQUIPMENT. This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
20NA1382021-05-03. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
19NA2552021-05-03. Service bulletin. STRUCTURE. This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
18NA3062021-05-03. Service bulletin. EQUIPMENT. This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).
18NA0992021-05-03. Service bulletin. EQUIPMENT. This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
16NA1092021-05-03. Service bulletin. STEERING. This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
PI0653A2021-04-26. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center A Service Agent (Dealer) during vehicle service may need to replace an engine turbocharger (TC). Any turbocharger that is returned to the Warranty Parts Center (WPC) will be inspected by engineering for root cause failure. The Warranty Part Center (WPC) has received turbochargers returned by Service Agents that have been disassembled, damaged during removal from the engine, electrical harnesses or connectors that have been cut or removed from the turbocharger and/or improperly packaged turbochargers resulting in shipping damage.
PI0369D2021-04-26. Service bulletin. EQUIPMENT:OTHER:LABELS. Frame Labels Visible from Outside of Vehicle Some customers may comment on disliking the appearance of the white labels that are visible on the frame The frame labels are only required during the manufacturing process and can be removed during pre-delivery inspection (PDI). There are two labels on the frame: the left front label (1) visible underneath the driver's door and the right front label (2) visible through the wheelhouse. Use care when removing the labels to prevent damage to the wax coating on the frame. Use a plastic trim tool to lift up on the edge and then pull the label off. The time required to perform this action is included in the PDI base time.
PI0281D2021-04-26. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS. Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
PI0281D2021-04-26. Service bulletin. STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS; EQUIPMENT ADAPTIVE/MOBILITY. Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
99-08-51-007F2021-04-26. Service bulletin. EQUIPMENT; WHEELS; EQUIPMENT ADAPTIVE/MOBILITY. Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility — Outside Company later in this bulletin.
99-08-51-007F2021-04-26. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; WHEELS; EQUIPMENT. Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility — Outside Company later in this bulletin.
15-NA-0822021-04-20. Service bulletin. SUSPENSION:FRONT. Clunking Noise from Front of Vehicle During Turns and/or Bumps Some customers may comment on a clunking noise originating from the front of the vehicle that is more predominant during turns or traveling over bumps. This may be caused by a damaged stabilizer shaft frame bracket. There have been some cases in which the bracket is cracked, as shown. This condition has been found to be the result of insufficient welds between the bracket and frame rail. There have been some cases on older vehicles of corrosion affecting the bracket
12-06-04-002E2021-04-20. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. Information on Exhaust Fluid Range, Exhaust Fluid Quality Poor, Service Exhaust Fluid System or Service Emission System Driver Information Center Messages
09-08-66-011C2021-04-20. Service bulletin. STRUCTURE:BODY; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. Information on Mounting Points for Pickup Box Accessories
07-08-49-020J2021-04-20. Service bulletin. ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® – The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.
06-00-89-031D2021-04-20. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE. OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
10-06-05-002B2021-04-20. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:FILTER/SCREEN. CLEAN EXHAUST FILTER SEE OWNERS MANUAL NOW or CLEANING EXHAUST FILTER KEEP DRIVING UNTIL MESSAGE IS CLEARED Displayed on DIC, DTC P2463 May Be Set
10-06-04-013C2021-04-20. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:DIESEL. Information on Diesel Exhaust Fluid (DEF) Filling Instructions, Frozen Tank Status and General Information In operating temperatures of 15°F (−9°C) or less, customers may comment on an “Exhaust Fluid Range” message displaying on the DIC even though the DEF fluid has been filled. When the DEF is frozen, the level sensor cannot determine the fluid level in the tank. If this occurs the logic of the PCM will assume a default fluid level. The logic will use the calculated range based on DEF dosing history and the assumed fluid level. If there is a high learned dosing rate and the fluid has not thawed to where the pins of the level sensor can function, there is a possibility the “Exhaust Fluid Range” message can set with the range from approximately 1609 km (1000 mi) to less than 482 km (300 mi), even though the tank is known to have fluid or be full. This is an operating characteristic of the system. However to increase or eliminate the range message, once the range drops below 482 km (300 mi), the DEF tank should be refilled. This should allow refill detection to occur and turn off the range indicator. The operator must be sure not to overfill the DEF tank using the instructions provided in this bulletin or in the owner’s manual. When in frozen tank status, refill detections are not allowed until the warning strategy reaches the point at which the distance remaining is less than 482 km (300 mi). The refill detection is dependent on the DEF thawing enough that the level sensor pins can be read. A fully frozen tank can take almost an hour to detect a refill, after the vehicle is started. This condition should not be confused with the situation described in PIP4864: Low Or Speed Limited Diesel Exhaust Fluid Message (DEF) Will Not Reset”.
08-06-04-003D2021-04-20. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE); EQUIPMENT. New Tool Availability — EN-48974 – EGR Cooler Pressure Tester Adapter Set to Diagnose Duramax® Diesel Engine EGR Cooler Engine Coolant Leaks into Combustion Chamber
02-06-01-022P2021-04-19. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL. Information on Diesel Engine Ticking Noise
PIP5163E2021-04-19. Service bulletin. FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5260D2021-04-19. Service bulletin. VISIBILITY:SUN/MOON ROOF ASSEMBLY. This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.