WenmarOpen by Wenmar Pro

Service bulletins for the 2013 Cadillac SRX

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

2008 on file from NHTSA, as of 2026-10-19.

About P228C on the 2013 Cadillac SRX: what the code means, and the bulletins and recalls about the same components.

By type

By component

By trouble code

By topic

Only bulletins with trouble code: P228C are shown. Show all

Bulletins, newest first
18NA0722020-04-27. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ENGINE; FUEL SYSTEM, GASOLINE. This technical bulletin provides a procedure to inspect the fuel system and replace the high pressure fuel pump if faulty for a Reduced Engine Power, MIL On, DTC P228C condition.
18NA0722018-05-21. Service bulletin. FUEL SYSTEM, GASOLINE. This technical bulletin provides a procedure to inspect the fuel system and replace the high pressure fuel pump if faulty for a Reduced Engine Power, MIL On, DTC P228C condition.
PIP5385D2018-02-21. Service bulletin. FUEL SYSTEM, OTHER:DELIVERY:FUEL PUMP; FUEL SYSTEM, GASOLINE. This Preliminary Information communication advises the technician on the steps to diagnose the concern, and the steps to repair the concern of Diagnostic Trouble Code P228C setting. The technician is to inspect the fuel and readings for the High Pressure Fuel Pump. The technician is to drain and clean fuel tank and all lines if contamination is found. The technician is to replace the high pressure fuel pump and the fuel inlet line to the high pressure fuel pump. The dealer is to request the customer complete the fuel survey attached and send to the fuel system engineer at the e-mail address provided. Latest revision added model years to the PI with no other changes. New revision adds model year and removes the customer surveys.
PIP52092017-12-22. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P00C6 and/or P228C set. Technician will need to inspect the terminals at the Engine Control Module for fit and tension as well as the crimp to wire connection. Terminals to inspect in the ECM are connector x2 terminals 3, 18, and 19 for the fuel rail pressure sensor. Also connector x3 terminals 16 and 32 for the high pressure fuel pump.
PIP5209B2017-08-15. Service bulletin. ENGINE; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P00C6 and/or P228C set. Technician will need to inspect the terminals at the Engine Control Module for fit and tension as well as the crimp to wire connection. Terminals to inspect in the ECM are connector x2 terminals 3, 18, and 19 for the fuel rail pressure sensor. Also connector x3 terminals 16 and 32 for the high pressure fuel pump.
PIP5209C2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication advises the technician to follow this Preliminary Information if there is a diagnostic trouble code P00C6 and or P228C set and normal Service Information diagnostics didn?t lead to a repair. Technician is to recheck the terminals at the Engine Control module for fit and tension as well as the crimp to the wire. The engine control module terminals to inspect are in the X2 connector. Inspect terminal number 3, 18 and 19 for the fuel rail pressure sensor and in the X3 connector terminals 16 and 32 for the high pressure fuel pump. The diagnostic trouble codes could set with as little as a 2 ohm resistance reading on these circuits. If any concerns are found replace the affected terminals and verify the repair.
PIP53852017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician with the steps to diagnose and repair vehicles that may have Service Engine Soon lamp or reduced engine power message came on and was cleared after cycling the key. Also technician may find a P228C set as current or history, and a prior history of High Pressure Fuel Pump replacement, and the customer has been using E85 fuel. If the Diagnostic Trouble Code is current follow Service Information instruction for the repair. If the code is set in history and there are no current drivability concerns take a large fuel sample and let it sit for a couple of hours looking for contamination. Verify the fuel pressure using a scan tool the actual and desired fuel pressures are very close to the same. If contamination is found in the tank then completely flush the fuel system and add e-10 fuel. Also remove the high pressure fuel pump inlet line from both ends. Using regulated air down to about 60 pounds per square inch or lower, blow through the inlet side of this pipe / hose. Inspect for restriction in the check valve built into this hose. If restricted then replace the pipe run a tank of premium fuel through the vehicle and reevaluate the concern.
PIP5385C2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP. This Preliminary Information communication advises the technician on the steps to diagnose the concern, and the steps to repair the concern of Diagnostic Trouble Code P228C setting. The technician is to inspect the fuel and readings for the High Pressure Fuel Pump. The technician is to drain and clean fuel tank and all lines if contamination is found. The technician is to replace the high pressure fuel pump and the fuel inlet line to the high pressure fuel pump. The dealer is to request the customer complete the fuel survey attached and send to the fuel system engineer at the e-mail address provided. Latest revision added model years to the PI with no other changes.
PIP5209A2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:WIRING; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P00C6 and/or P228C set. Technician will need to inspect the terminals at the Engine Control Module for fit and tension as well as the crimp to wire connection. Terminals to inspect in the ECM are connector x2 terminals 3, 18, and 19 for the fuel rail pressure sensor. Also connector x3 terminals 16 and 32 for the high pressure fuel pump.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.