WenmarOpen by Wenmar Pro

Service bulletins for the 2019 BMW X4

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

273 on file from NHTSA, as of 2026-10-19.

By type

By component

Only bulletins with component: Backup camera are shown. Show all

Bulletins, newest first
B0903212022-06-21. Service bulletin. BACK OVER PREVENTION:SOFTWARE. In some rare cases a customer vehicle might be excluded from one or more Remote Software Upgrade(RSU) campaigns. This SIB gives an overview how to identify these vehicles and how to proceed in case of a customer complaint.
B6629192021-04-26. Service bulletin. BACK OVER PREVENTION. TOP VIEW CAMERA IMAGE IS MISALIGNED: The top view image of the vehicle is misaligned when observed in the Control Information Display (CID).
B6401212021-04-26. Service bulletin. BACK OVER PREVENTION. WHISTLING NOISE COMING FROM FRESH AIR INLET (ENGINE COMPARTMENT): A whistling noise is present from the fresh air inlet area (engine compartment bulkhead area), in the right front area of the vehicle, at speeds above 40 mph.
B6629192020-12-21. Service bulletin. BACK OVER PREVENTION: CAMERA SYSTEM; EQUIPMENT. TOP VIEW CAMERA: The top view image of the vehicle is misaligned when observed in the Control Information Display (CID). When the vehicle is parked in a parking spot with line markings, it is clearly noticed in the CID that the lines are not parallel to the side of the vehicle. This may be noticed on either the driver side, passenger side or both.
B6617202020-12-21. Service bulletin. BACK OVER PREVENTION. SURROUND VIEW - PARKING VIEW IMAGES DISPLAYED INCORRECTLY: After programming and shifting into reverse, there may be various sporadic concerns regarding the rearview camera and the surround view (top view) camera images in the CID (Central Information Display).
B6629192020-07-27. Service bulletin. VISIBILITY; BACK OVER PREVENTION. TOP VIEW CAMERA: IMAGE IS MISALIGNED: The top view image of the vehicle is misaligned when observed in the Control Information Display (CID). When the vehicle is parked in a parking spot with line markings, it is clearly noticed in the CID that the lines are not parallel to the side of the vehicle. This may be noticed on either the driver side, passenger side or both. Side view camera loose fitment in the exterior mirror bracket, causing changes to the top view image.
B6608172020-04-27. Service bulletin. EQUIPMENT; BACK OVER PREVENTION. REAR VIEW CAMERA FAILS TO DISPLAY IMAGE: This Service Information Bulletin (Revision 6) replaces SI B66 08 17 dated January 2020. Sporadically when the rear view camera is activated no image appears in the display. The rear view camera can be activated by either: 1. Selecting reverse with the shift selector 2. Camera activation via the button on the center console Camera function returns after a terminal change.
B6102202020-04-20. Service bulletin. BACK OVER PREVENTION; VISIBILITY:WINDSHIELD WIPER/WASHER. KNOCKING NOISE FROM WASHER FLUID RESERVOIR: When driving over uneven pavement or cobblestones a knocking noise is present from the passenger side front area (A pillar). Once the vehicle is driven on a flat even surface; the noise is no longer present. CAUSE Washer fluid reservoir movement caused by mounting bracket clearance.
B3405172020-04-20. Service bulletin. BACK OVER PREVENTION; SERVICE BRAKES, HYDRAULIC; WHEELS; POWER TRAIN. TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs.
B6608172020-02-18. Service bulletin. BACK OVER PREVENTION; ELECTRICAL SYSTEM:SOFTWARE. REAR VIEW CAMERA FAILS TO DISPLAY IMAGE: This Service Information Bulletin (Revision 5) replaces SI B66 08 17 dated March 2018. Sporadically when the rear view camera is activated no image appears in the display. The rear view camera can be activated by either: 1. Selecting reverse with the shift selector 2. Camera activation via the button on the center console Camera function returns after a terminal change. Note: This error situation can rarely if ever be duplicated on demand. Head-unit interface software start-up synchronization error for the rear view camera.
B6629192020-01-21. Service bulletin. LANE DEPARTURE; BACK OVER PREVENTION. TOP VIEW CAMERA: IMAGE IS MISALIGNED. The top view image of the vehicle is misaligned when observed in the Control Information Display (CID). When the vehicle is parked in a parking spot with line markings it is clearly noticed in the CID that the lines are not parallel to the side of the vehicle. This may be noticed on either the driver side passenger side or both. The arrow identifies the line which is shown as not parallel or straight alongside the vehicle. Side view camera loose fitment in the exterior mirror bracket causing changes to the top view image.
B6617192019-09-23. Service bulletin. BACK OVER PREVENTION: AUTOMATIC SYSTEM BRAKING; SERVICE BRAKES, HYDRAULIC. ACTIVE PARK DISTANCE CONTROL (PDC): UNDESIRED BRAKING. The vehicle applies the brakes on its own when reversing onto an inclined roadway or driveway. This applies only to the situation where the Active PDC option is activated via the iDrive. Software of the ultrasonic sensors and PDC control unit.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.