WenmarOpen by Wenmar Pro

Service bulletins for the 2015 BMW i3

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

294 on file from NHTSA, as of 2026-10-19.

By type

By component

Bulletins, newest first
B3106142018-12-10. Service bulletin. SUSPENSION; SUSPENSION:FRONT. Front Axle Noise when Turning at Low Ambient Temperatures. A grating and/or squeaking noise from the front axle occurs when turning at low speeds or idle. The noise is most noticeable at low temperatures (approx. 32 degrees F), but not unusual at higher temperatures and after driving. Friction between the spring pad and the strut upper support bearing is causing the noise.
B6410162018-12-10. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. KNOCKING NOISE FROM RF WHEEL AREA WHEN A/C IS ACTIVATED. A knocking noise is heard when entering drive readiness or after driving a short distance with the air conditioning activated. This only affects vehicles with a heat pump (option code 4T9). Note: The noise can only be reproduced once after a restart, then the vehicle must sit for some time before the noise can be heard again. Air Conditioning (A/C) receiver/dryer located near the RF wheel well area.
B6138142018-12-10. Service bulletin. ELECTRICAL SYSTEM. Drivetrain Malfunction (CCM 794) with Isolation Faults. The Drivetrain Malfunction check control message (CCM 794) is displayed, either while driving or when starting up. The following faults are stored in the vehicle: EME: 22280F and/or 222814 SME: 21F0E3 and/or 21F0E4 When the CCM is present, there are no apparent drivability concerns. After allowing the vehicle to rest and then restart, the CCM typically does not reappear. After allowing the vehicle to rest and then restart, the CCM typically does not reappear. CAUSE The cause of an isolation fault is generally a resistance between HV+ or HV- and the shield/chassis ground, which is below a predetermined threshold. The following procedure addresses these faults when caused by a defect in the cable between the HV battery and the EME, as well as when excess moisture is present inside the REx eMachine. This moisture condenses and triggers the above-mentioned faults after a long REx runtime followed by rapid cooling.
B6112162018-12-10. Service bulletin. ELECTRICAL SYSTEM. DC Charging - Customer Focused Diagnosis. Diagnosing DC charging complaints requires a precise problem description from the customer, as well as thorough vehicle-side work to find a reliable root cause. Because of the sporadic nature of majority of DC charging issues, the customer's input is invaluable to finding the correct solution.
B6108162018-12-10. Service bulletin. ELECTRICAL SYSTEM. "DC/DC Converter does not supply sufficient 12V power. Customer probably has a CCM stating ""Battery is not charged"" (CCM-ID: 213) is displayed. Customer may report a variety of other issues: Erratic KOMBI behavior Malfunction of any device powered by 12V electrical Vehicle not starting, or reduced 12V power while driving Vehicles from production date 10/1/2015 with the following software levels: I01: 15-11-501 up to and including 16-07-500 I12: 15-11-501 up to and including 16-03-503 CAUSE EME Software"
B6104162018-12-10. Service bulletin. ELECTRICAL SYSTEM. "SI B61 04 16 General Electrical June 2016 Technical Service EME Fault Code 222C02 Following Replacement or Programming- Diagnosis. Programming, (e.g. following replacement), can cause EME fault code ""222C02 - Electronic immobilizer protection against tampering: expected response implausible"" to be stored. After clearing, the fault comes back during a test drive. Improper EME software"
B2201162018-12-10. Service bulletin. STRUCTURE; EQUIPMENT. Service Action: Replace the Motor Mount Screws. A sudden loss of traction while accelerating sharply may damage the engine mounts.
B8403142018-12-10. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT. Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.
B6609162018-12-10. Service bulletin. VEHICLE SPEED CONTROL:CRUISE CONTROL; EQUIPMENT; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL. """Collision Warning Failed"" or ""Pedestrian Warning Failed"" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the ""green lines"""
B6111162018-12-10. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. The Charging Cable Does not Release from the Charging Socket after Charging. The charging cable does not release from the charging socket after charging. High voltage charging socket housing tolerance prevents the lock actuator pin from mechanically disengaging from the charging cable.
B5401162018-12-10. Service bulletin. VISIBILITY:SUN/MOON ROOF ASSEMBLY. "This Service Information bulletin supersedes SI 54 01 16 dated February 2016. A Delivery Stop has been issued on i3 BEV vehicles produced from December 09, 2015 to January 22, 2016. Vehicles are equipped with a sunroof as part of the Shadow Sport limited edition. The sunroof may not be properly sealed, so that leaks could possibly develop. This bulletin will be updated with repair instructions and warranty information when it becomes available. AFFECTED VEHICLES Affected vehicles can be identified with a ""open campaign"" in DCS Warranty Vehicle Inquiry or ISPA Light. ""A delivery stop has been issued for this vehicle. Dealers must ensure that all Campaigns are completed before retail delivery to the customer. See Service Information Bulletin B54 01 16 for repair instructions."""
B3106142018-12-10. Service bulletin. SUSPENSION. Front Axle Noise when Turning at Low Ambient Temperatures. A grating and/or squeaking noise from the front axle occurs when turning at low speeds or idle. The noise is most noticeable at low temperatures (approx. 32 degrees F), but not unusual at higher temperatures and after driving. Friction between the spring pad and the strut upper support bearing is causing the noise.
B6408162018-12-10. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Reduced or No HVAC Heat Output. I12 & F30 PHEV - The heat is not functioning during electric driving and/or the heat output is reduced or fluctuating when driving with the combustion engine. I01 - The heat is not functioning at all. The issue can occur sporadically for all vehicles and will not have any associated fault codes. IHKA software with I-Level: I01, I12I001-15-11-504 F30 PHEV F020-15-11-505
B2204152018-12-10. Service bulletin. EQUIPMENT. Engine and Gearbox Suspension. Technical Service his Service Information bulletin supersedes SI B22 01 15 dated February 2016. A sudden loss of traction while accelerating sharply may damage the engine mounts.
B1227152018-12-10. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:SOFTWARE. This Service Information bulletin supersedes SI B12 27 15 dated November 2015 SUBJECT Service Engine Soon (MIL) - IHKA FC 801375 & 8013A3. The Service Engine Soon light (MIL) is currently or intermittently illuminated in the instrument cluster and one or both of the fault codes below are stored in the Automatic Climate Control (IHKA). 801375 - Electric auxiliary heater (high voltage) is stored: Temporary fault detected after software reset CAUSE: IHKA software or Electric Heater (EH).
B6604162018-12-10. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. """Comfort Access Restricted"" Check Control Message is Displayed. ""Comfort Access Restricted"" CCM (Check Control Message) is permanently displayed.. The CCM ID: D0h. The comfort access is functioning correctly. No comfort access aerial fault codes stored in the BDC (Body Domain Controller). Software error in the BDC"
B6526152018-12-10. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Hissing Noise from Speakers when Radio Volume is Turned Down. There is an audible hissing noise from the speakers when there is no active audio source. This noise is most apparent with the engine and climate system fan turned off. Software in the HK HiFi amplifier.
B6507162018-12-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. NBT and Entry Head Unit Software Update for Improved Satellite Radio Reception. Poor Satellite Radio reception CAUSE After this software update there is a slight improvement in Satellite Radio reception for these vehicles when receiving their signal from XM Satellites. This is due to the changeover from Sirius Satellite broadcasting to XM Satellite broadcasting in 2016 (See SI B65 19 15).
B6506162018-12-10. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; ELECTRICAL SYSTEM. NBT Head Unit Aborts Import of CD. While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software
B6505162018-12-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES. "False Alarms of the Anti-Theft Alarm System. The alarm (DWA) siren continues to activate after locking vehicle An ""unapproved"" device is connected to the On-Board Diagnostics (OBD) port of the vehicle. This keeps the Ethernet communication line active which triggers the alarm when the vehicle tries to enter sleep mode."
B6108152018-12-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. "High-Voltage Charging Cable Lock Malfunction. One of the following situations can occur: The vehicle cannot be charged via the high-voltage charging procedure. The indicator light on the charging socket lights up white and does not change colors. The high-voltage charging cable cannot be unlocked and disconnected. One of the following faults codes is also stored in the Charging Interface Module (LIM): 805532 ""High-voltage charging socket: Lock on the charging plug, status implausible"" 805503 ""High-voltage charging socket: Charging plug lock, line disconnection"" CAUSE The emergency-operation tensioning strap is jammed. The actuator drive for the charging socket is not working."
B6103162018-12-10. Service bulletin. ELECTRICAL SYSTEM. "SME Fault Code 21F0D2 Causes Erroneous CCM. CCM message ""Drive: Check as soon as possible"" (CCM-ID 49) is displayed during or after charging session with battery heating (preconditioning) active. Fault code ""21F0D2 - High voltage connector: Main switch: stuck negative switch contactor"" stored erroneously due to HV battery heating deactivation too late in the charging process. NOTE: The following consequential faults may be stored as well, but can be ignored until the release of ISTA/P 3.59.0: 21F153 - High voltage connector: safety concept, Level 2: Switch off detected 21F2A9 - SME: Safety Concept, Level 2: Timeout request for protective opening via ACAN SME software"
B6102162018-12-10. Service bulletin. ELECTRICAL SYSTEM. CSC Communication Errors. The vehicle cannot be put into drive readiness or the high voltage system could automatically deactivate during driving. Failure of communication on the CAN bus due to one or more faulty cell supervision circuits (CSC). As a result, the switch contactor in the high-voltage battery opens.
B5114152018-12-10. Service bulletin. STEERING; EQUIPMENT. SI B51 14 15 Body Equipment March 2016 Technical Service This Service Information bulletin supersedes SI B51 14 15 dated May 2015. SUBJECT Grinding Noise from Steering Wheel When Turning. Customer complains of a noise from the steering wheel while driving. Due to insufficient gap, the steering column lower shroud rubs against the steering wheel.
B1203162018-12-10. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. EME No Longer Communicates after HV Charging. On the affected i3 vehicles (with software integration levels 15-11-501 through 15-11-504), the Drive Readiness can no longer be established after attempting to charge the HV battery. In such a case, EME no longer communicates with ISTA. In some cases, various calibration values are lost (e.g. resolver angle). CAUSE Vehicle was charged before Transport Mode removal. This may cause: Irreparable damage to the EME. Taught-in values to be set to default values, requiring repetition of teach-in process.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.