WenmarOpen by Wenmar Pro

Service bulletins for the 2015 BMW i3

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

294 on file from NHTSA, as of 2026-10-19.

By type

By component

Only bulletins with component: Driver assistance are shown. Show all

Bulletins, newest first
B6401202020-04-20. Service bulletin. ELECTRICAL SYSTEM; SERVICE BRAKES, HYDRAULIC; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE. AIR CONDITIONING DOES NOT COOL: The air conditioning no longer cools the vehicle. A vehicle test reveals one or both of the following faults stored in the IHX_I1 Control Module: 801295 - Heat Pump pressure-temperature sensor 2 after air condition compressor: pressure short to ground / open circuit 80112A - Heat Pump pressure-temperature sensor 2 after air condition compressor: temperature - short to ground A short circuit at the temperature sensor due to aluminum particles in the high-pressure line.
B6109202020-04-20. Service bulletin. ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); ELECTRICAL SYSTEM; STEERING; SUSPENSION. CHECK CONTROL MESSAGES FOR BRAKE SUSPENSION AND AIR BAG SYSTEM MALFUNCTION: Multiple check control messages (CCM) can display for brake suspension and air bag system malfunction. The customer may also complain about any of the following: Engine can no longer be switched off Drive position (D) cannot be engaged on the gear selector switch (GWS) Reduction of steering assist After an engine emergency shut-off (either a prolonged long press; or 3 consecutive short presses of the Start/Stop button) and the vehicle going to sleep (identifiable by the lighting of the "Start/Stop button") everything resumes normal functionality and the CCM messages no longer appear.
B3405172020-04-20. Service bulletin. BACK OVER PREVENTION; SERVICE BRAKES, HYDRAULIC; WHEELS; POWER TRAIN. TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs.
B6609162018-12-10. Service bulletin. VEHICLE SPEED CONTROL:CRUISE CONTROL; EQUIPMENT; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL. """Collision Warning Failed"" or ""Pedestrian Warning Failed"" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the ""green lines"""
B2204152018-12-10. Service bulletin. ENGINE; EQUIPMENT; TRACTION CONTROL SYSTEM. A sudden loss of traction while accelerating sharply may damage the engine mounts.
B6507152018-12-10. Service bulletin. AIR BAGS; ELECTRICAL SYSTEM; FORWARD COLLISION AVOIDANCE. "This Service Information bulletin supersedes SI B65 07 15 dated April 2015. designates changes to this revision SUBJECT Airbag Warning Light ON: Fault 930BE8, High-voltage System Shutdown . The airbag warning light in the instrument cluster is on, or the check control message (CCM) ""Restraint system faulty"" is displayed. The advance crash safety module (ACSM4I) has fault code 930BE8 ""High-voltage system switchoff Range extender Electrical Machine Electronics (REME)/battery management electronics: Resistance too high"" stored. A sporadically poor connection causes high resistance in the airbag ignition circuit."
6604142018-11-13. Service bulletin. FORWARD COLLISION AVOIDANCE. Front Collision Warning Check Control Message Displayed in CID. Occasionally while driving, a check control message (CCM) for Front Collision Warning is displayed in the Central Information Display (CID). This message is cleared from the CID by clicking on "OK" using the iDrive controller. CAUSE The KAFAS (camera-based driver support system) camera is affected by environmental conditions such as: * Direct sunlight (sunrise or sunset) * Rain * Fog * Dirt * Snow * Ice * High interior temperatures (may also cause a CCM to be displayed upon starting the vehicle) ?? Fault code 0x800AC0 - KAFAS camera switch off due to over temperature The pictures below show the direct sunlight causing the CCM: INFORMATION This is the current text in the Owner's Manual for the Front Collision Warning (FCW): The system may not be fully functional in the following situations: * In heavy fog, rain, sprayed with water or snowfall * In tight curves * If the driving stability control systems are limited or deactivated: for example, the DSC is off. * If the camera view field of the front windshield is dirty or covered. * Up to 10 seconds after the start of the engine, via the Start/Stop knob. Direct sunlight will be added as one of the causes for the FCW CCM.
3207142018-11-13. Service bulletin. AIR BAGS; POWER TRAIN; STEERING; ELECTRICAL SYSTEM; LANE DEPARTURE. "SUBJECT Sporadic Electronic Power Steering (EPS) Warning Lamp when Starting Drive Readiness. An EPS warning lamp may intermittently light up in the instrument cluster when starting drive readiness. No steering assistance is available at this time. After a terminal change (switching the ignition off and on again), the warning lamp is no longer illuminated. Software error in the EPS control unit Fault code ""FC 4823E6-Internal control unit-power pack faulty"" may be stored in the EPS."
B6621162018-11-05. Service bulletin. ENGINE; LANE DEPARTURE: SENSING SYSTEM: OTHER; SERVICE BRAKES. KAFAS CAMERA-BASED ASSISTANCE SYSTEM LIMITS. INFORMATION The situations described above may all be caused by known limitations of the system such as: Dirty windshield Incomplete calibration process Unsuccessful calibration Restricted visibility- weather conditions or parked vehicles Missing lamps on target vehicle Non-standard vehicle exterior surfaces Insufficient ambient lighting Abrupt motion of target vehicle.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.