WenmarOpen by Wenmar Pro

Service bulletins for the 2013 BMW ActiveHybrid 5

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

369 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
B0112242024-10-28. Warranty extension. POWER TRAIN. The Electrical Machine Electronics (EME)Modules limited warranty for defects in materials or workmanship has been extended to 10years/120,000 miles as determined from the original in-service date
B3405172020-04-20. Service bulletin. BACK OVER PREVENTION; SERVICE BRAKES, HYDRAULIC; WHEELS; POWER TRAIN. TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs.
1217122019-07-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING. N52T / N55 with 8HP45: Delay in Engine Response. A customer may complain of a delay in engine response after decelerating at low road speeds and then reaccelerating. This can occur when the transmission remains in a high gear due to a delay in the transmission downshifting. This situation can be more noticeable while driving on roads with slight turns or with an increasing gradient. Unfavorable EGS and DME software
B2703152018-12-10. Service bulletin. POWER TRAIN. Vibration or Shudder from Driveline when Accelerating from a Stop. Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle deviation outside tolerance? 44011B - Set torque outside of the torque characteristic curve EGS ? 420611 - DSC interface (wheel speed): non-permitted deviation of wheel speed (actual speed of wheel RL/FL/RR/FR, 0x254) from output speed and turbine speed DSC ? 48097D - Transfer box: Fault, clutch position known, only rear-wheel drive These symptoms or faults would be stored on a vehicle with low mileage (< 12,500 miles). CAUSE A front or rear differential with the incorrect gear ratio was installed in the car. The front and rear differentials need to be geared exactly the same for the xDrive to function properly.
B2403162018-12-10. Service bulletin. POWER TRAIN:DRIVELINE:DRIVESHAFT; POWER TRAIN. TRANSMISSION OVERHEATING WARNING ON GEN2 HYBRIDS. Transmission warning light is illuminated and vehicle goes into fail-safe mode. The following Check Control messages may be displayed: CC 585 - Hybrid System Fault! CC 569 - Drivetrain, stop carefully! CC 586 - Drivetrain no restart! During diagnosis, some of the following fault codes related to transmission overheating, may be stored in the EGS control module: 44D31F1 - Temperature sensor; excessive temperature in transmission (1450 C) 44D671 - Temperature sensor system; Hotmode 1 44D672 - Temperature sensor system; Hotmode 2 with driver message 44D673 - Temperature sensor system; Hotmode 2 with torque reduction Vehicle's repair history shows a recent transmission fluid replacement under a regular maintenance program. Transmission has been overfilled during the last fluid replacement service.
B1109162018-12-10. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY:BELL HOUSING; POWER TRAIN. N63, N63TU, S63 and S63TU Engines: Oil Leak from the Rear of the Engine and Transmission Bell Housing. Customer complains that engine oil is leaking from the center of the vehicle. When verified, the engine oil residue can be seen leaking from between the engine and the transmission bell housing.
B2407122018-12-10. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. "SI B24 07 12 Automatic Transmission March 2016 Technical Service bulletin. Hybrid Automatic Transmission: Fluid Maintenance Service Interval. INFORMATION Only properly trained personnel, who have passed all applicable technical training courses, should perform any maintenance or repairs on any Hybrid or Electric Vehicle. Work performed by unqualified persons may result in severe injury or damage to the vehicle. Additional information may be found in REP 61 00... Observe safety instructions when handling electric vehicles. This requirement is due to the hybrid-specific components that are contained in the transmission. Refer to Repair Instruction 00 00 630, ""Automatic transmission fluid service (GA8P70Z) N55 hybrid,"" for the proper servicing procedure. Refer to SI B00 09 12 for BMW Maintenance Program claim-related information."
B0009122018-12-10. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; POWER TRAIN. "Maintenance and General Hints March 2016 Technical Servic. This Service Information bulletin supersedes SI B00 09 12 dated August 2015. designates changes to this revision SUBJECT Hybrid Automatic Transmission: Fluid Maintenance Service Interval. The automatic transmission fluid is required to be changed at every second or third engine oil service depending on the production date of the vehicle (""connected"" maintenance service to the engine oil service at Service Counter numbers: 2, 4, 6, or 3, 6, 9 etc.). Vehicles produced up to 7/13 (Option Code SA8KC) The automatic transmission fluid is required to be changed at every second engine oil service. Vehicles produced from 7/13 (Option Code SA8KL) The automatic transmission fluid is required to be changed at every third engine oil service. Refer to SI B24 07 12 for additional information."
3101122018-12-03. Service bulletin. POWER TRAIN. Clicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
6122132018-12-03. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. """Increased battery discharge!"" CC Message upon Startup. CAUSE A software error in the Intelligent Battery Sensor causes an incorrect State of Charge (SoC) to be stored in the DME. The power management system then interprets this as a heavily discharged battery and informs the customer via a CC message. In reality, the battery does not have a problem."
1217132018-12-03. Service bulletin. ENGINE; POWER TRAIN. N55: Engine Difficult to Start at Cold Ambient Temperatures. The complaint may include any of the following symptoms: * The engine stalls immediately after a cold start before driving away * The engine may run roughly or misfire after a cold start * The engine does not start cold or may take several attempts * To assist starting when cold, the accelerator may need to be depressed slightly and the idle speed raised for a few seconds so the engine does not stall This can occur most frequently at outside ambient temperatures between -15°C and + 15°C. It is possible that the Service Engine Soon (MIL) lamp is on with misfire fault(s) stored, but it is equally possible that there will be no faults stored in the DME. Unfavorable DME software Cold start or idling problems may arise due to poor fuel quality. The use of summer fuel during cold outside temperatures may also lead to such problems.
1201132018-12-03. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION. MN16 Engine: FC 2D9B Knock Sensor, Signal Is Stored in the DME. Certain areas of the US experience extremely cold climate conditions during the winter months, which can cause the Service Engine Soon lamp to illuminate while the engine temperature is increasing to full operating temperature. The following fault may be stored in the DME: ??FC 2D9B Knock Sensor, Signal CAUSE Unfavorable DME knock sensor diagnostic at outside ambient temperatures below -5° C
1216112018-12-03. Service bulletin. ENGINE; POWER TRAIN. N55 Engine Failsafe - FC 120308 Boost Pressure Control, Plausibility: Pressure Too Low Stored in DME Fault Memory. INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode).
2702132018-12-03. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Knocking Noise from Driveline During Low-speed Turning. A cracking or knocking noise is heard from the driveline on sharp turns at low driving speeds (<15 mph). CAUSE Software calibration error in the transfer case control unit (Longitudinal Torque Module or LMV)
1217122018-12-03. Service bulletin. ENGINE; POWER TRAIN. A customer may complain of a delay in engine response after decelerating at low road speeds and then reaccelerating. This can occur when the transmission remains in a high gear due to a delay in the transmission downshifting. This situation can be more noticeable while driving on roads with slight turns or with an increasing gradient. Unfavorable EGS and DME software
2403132018-11-26. Service bulletin. ENGINE; POWER TRAIN. N52T/N55 with 8HP45: Delay in Engine Response. When slowing down to lower suburban road speeds and then accelerating, a delay in engine response may be experienced. This situation may be more noticeable when driving in a bend in the road or on roads with a rising gradient. Unfavorable EGS and DME software calibration
1201132018-11-26. Service bulletin. POWER TRAIN. "Transmission Intermittently Goes into ""P"" or ""N"" after MSA Engine Start. The transmission can intermittently go into the Park (P) or Neutral (N) position after an MSA engine start without any customer influence. This problem is very sporadic, difficult to reproduce, and no relevant faults are stored. Unfavorable DME/EGS software"
2403132018-11-13. Service bulletin. POWER TRAIN; ENGINE; ELECTRICAL SYSTEM:SOFTWARE. A customer may complain of a delay in engine response after decelerating at low road speeds and then reaccelerating. This can occur when the transmission remains in a high gear due to a delay in the transmission downshifting. This situation can be more noticeable while driving on roads with slight turns or with an increasing gradient. Unfavorable EGS and DME software
1217122018-11-13. Service bulletin. ENGINE; POWER TRAIN. N52T / N55 with 8HP45: Delay in Engine Response. A customer may complain of a delay in engine response after decelerating at low road speeds and then reaccelerating. This can occur when the transmission remains in a high gear due to a delay in the transmission downshifting. This situation can be more noticeable while driving on roads with slight turns or with an increasing gradient. Unfavorable EGS and DME software
1201132018-11-13. Service bulletin. POWER TRAIN. "Transmission Intermittently Goes into ""P"" or ""N"" After MSA Engine Start. After an MSA engine start, the transmission intermittently goes into the Park (P) or Neutral (N) position without any customer influence. This problem can be sporadic, difficult to reproduce, and no relevant faults are stored. Unfavorable DME/EGS software"
1201152018-11-13. Service bulletin. POWER TRAIN. SUBJECT N20 and N26 Differential Pressure Sensor Fault 195002 Stored in DME. The Service Engine Soon (MIL) light is on with the following differential pressure sensor fault stored: z 195002 - Differential pressure sensor, tank vent valve, electrical: Short circuit to ground During engine operation, vibration and movement of the sensor can damage the pin contacts of the harness connector, or cause a break in the wiring.
B2704152018-11-05. Service bulletin. POWER TRAIN:DRIVELINE; WHEELS. Shudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
B2407122018-11-05. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION. "This Service Information bulletin supersedes SI B24 07 12 dated November 2012 SUBJECT Hybrid Automatic Transmission: Fluid Maintenance Service Interval. INFORMATION Only properly trained personnel, who have passed all applicable technical training courses, should perform any maintenance or repairs on any Hybrid or Electric Vehicle. Work performed by unqualified persons may result in severe injury or damage to the vehicle. Additional information may be found in REP 61 00... Observe safety instructions when handling electric vehicles. This requirement is due to the hybrid-specific components that are contained in the transmission. Refer to Repair Instruction 00 00 630, ""Automatic transmission fluid service (GA8P70Z) N55 hybrid,"" for the proper servicing procedure. Refer to SI B00 09 12 for BMW Maintenance Program claim-related information."
B3301152018-11-05. Service bulletin. STRUCTURE; POWER TRAIN. Cracking in Rear Differential Mount Bushing. During inspection, the rear differential mount in the rear axle support shows signs of cracking.
6103142018-11-05. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE ? The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.