WenmarOpen by Wenmar Pro

Service bulletins for the 2015 BMW 740Li

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

208 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Equipment and accessories are shown. Show all

Bulletins, newest first
B1303152018-12-10. Service bulletin. FUEL SYSTEM, GASOLINE; EQUIPMENT. SI B13 03 15 February 2016 Fuel Systems Technical Service This Service Information bulletin supersedes SI B13 03 15 dated March 2015 and replaces SI B13 04 13 dated March 2014. SUBJECT N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
B0703142018-12-10. Service bulletin. ENGINE; STEERING; ELECTRICAL SYSTEM; EQUIPMENT. This Service Information bulletin supersedes SI B07 03 14 dated October 2015. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
B6513132018-12-10. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM:SOFTWARE. "?This Service Information bulletin supersedes SI B65 13 13 dated October 2014. SUBJECT Headunit-High: CID Is Blank and ""NO SIGNAL"" Is Displayed . Intermittently the Central Information Display (CID) is blank and ""NO SIGNAL"" is displayed on the CID. Fault Code B7F8C3 ""no response from CID (HW error: loss of CID communication)"" is stored in the HU-H Note: If Fault Code E1C440 ""Headunit Reset"" is also stored in the HU-H, this Service Information is not effective! Follow relevant test plan using ISTA diagnosis. Software error in the HU-H."
B6507092018-12-10. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Whistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
B6216162018-12-10. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT. ?VERTICAL LINES IN HEAD-UP DISPLAY. Run diagnostics and if display is found to be damaged, replace Head-Up display.
B1615142018-12-10. Service bulletin. EQUIPMENT; FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY; FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY. SI B16 15 14 January 2016 Fuel Supply Systems Technical Service.This Service Information bulletin supersedes SI B16 15 14 dated December 2014, designates changes to this revision. SUBJECT NVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak . The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm. CAUSE: Contamination of the NVLD pressure switch diaphragm and/or the contamination of the NVLD dust filter.
B6216162018-11-26. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; EQUIPMENT:ELECTRICAL. WARRANTY INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks or the BMW Certified Pre-Owned Program. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowances. Work time labor operation code 61 00 006 is not considered a Main labor operation; however, it does require an individual punch time and an explanation on the repair order and in the claim comments Vehicle Programming and Coding When ISTA/P automatically reprograms and codes all the vehicle's control modules that currently do not have the latest software, and if control module failures occur during this programming procedure: ? Please claim this consequential control module-related repair work under the defect code listed in this bulletin with the applicable KSD2/AIR labor operations. Other Repairs Control module failures that occurred prior to this programming procedure and/or additional work is performed as a result of performing the ISTA diagnostics and related test plans: ? When covered under an applicable limited warranty, claim the control module-related and/or other repair work using the applicable defect code and labor operations in KSD2/AIR.
6520132018-11-13. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT ADAPTIVE/MOBILITY. Vehicle inTransport Mode Cannot Be Unlocked with Remote Control. When the vehicle is in transport mode, intermittently it cannot be unlocked via the remote control key. CAUSE When the vehicle is in transport mode, to reduce power consumption, the software is designed to disable the outside antenna receiver from waking up the vehicle.
5133142018-11-13. Service bulletin. EQUIPMENT:OTHER:LABELS; STRUCTURE:BODY. This Service Information bulletin supersedes SI B51 33 14 dated October 2014. designates changes to this revision SUBJECT New "Gas Door Operation" Instruction Label. Initial quality reports show the customers are not certain how to open and close the fuel filler flap.
7102142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; EQUIPMENT:OTHER:LABELS. Service Action: Replace Emission Label. Certain 2015 model year vehicles with N47T and N57T diesel engines were produced with an "emissions" label which contains incorrect information pertaining to the 2015 model year. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at VDCs will be repaired prior to dealer delivery.
6516142018-11-13. Service bulletin. EQUIPMENT:ELECTRICAL. Central Information Display Intermittently Dimming or Flashing Off/On. Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID.
6505142018-11-13. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Traffic Information Is Inoperative. The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.
6103142018-11-13. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ELECTRICAL SYSTEM. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
5116132018-11-13. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. Bang & Olufsen Sound System: Loudspeaker Cover Rattles. The top center loudspeaker cover rattles when driving on rough roads. CAUSE Poor loudspeaker cover fitment to the speaker assembly.
8405142018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Service Action: Bluetooth Software (KISU Data) Update. This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new KISU software improves the Bluetooth functionality in our vehicles, and it helps keep us up-to-date with technology innovation. Please implement the Bluetooth Software Update Service Action. This Service Action will be in effect until March 2015. Thank you for your continuous support. Improved KISU data (Customer Initiated Software Update) is now available for installation in these vehicles via the USB port. Improved functionality for COMBOX: z Detailed view of the text messages z Android device connection stability (linked contacts causing BT disconnection) Improved functionality for HU-H: z Reconnection strategy z 3rd Party App Metadata - Album art and song title Note: This Service Action is to be completed only at the dealer. You (dealers) will be receiving vehicles from the VDCs that will require this service action to be completed prior to customer delivery.
8404122018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM:SOFTWARE. iPhone 6, 6 Plus, 5, 5S, 5C, 4S, 4, and 3GS with iOS 8.x Information. INFORMATION There is one major difference in functionality since iOS 8.0 was released. Scenario: z The customer leaves the vehicle and turns his or her phone off. z He or she turns the phone back on. z He or she enters the vehicle, but does not unlock the phone and start driving. Result: z The phone reconnects to the Bluetooth system (normal). z However, it does not transfer the contact list (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle they must unlock the phone (passkey) With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following: z www.bmwusa.com/bluetooth website NOTE: This SI will be updated as new information is received.
6522142018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Automated Activation of Navigation System During PDI/QC1. INFORMATION Important: The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1, the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system. Note: This VIN-specific NAV enabling code is then also automatically stored in the Repair Kit in the Aftersales Assistance Portal (ASAP). The automated INITIAL NAV enabling code request and activation of the navigation system will take no longer than 1 minute. After finishing "Delete Transport Mode," the navigation system in the vehicle will be active without entering the 20-digit INITIAL NAV enabling code manually or in ISTA. If the navigation system is not active and asking for the enabling code, turn off the ignition and wait for the head unit to enter sleep mode (approx. 3 minutes). After that, turn on the ignition again. The head unit will start up and the navigation system is activated. If the INITIAL NAV enabling code for first-time activation of the navigation system is not requested or delivered automatically, it still can be ordered manually through the Parts department and activated in the vehicle through the iDrive controller, by entering the 20-digit enabling code manually.
6133142018-11-13. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT ADAPTIVE/MOBILITY. The Controller Responds Slowly or Not at All. When the customer presses or turns the controller, there is no or a delayed response. This can sporadically occur. Software in the controller
6130142018-11-13. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY; EQUIPMENT ADAPTIVE/MOBILITY. BMW Maintenance Program: 12-Volt Battery Replacement Measure.
3405142018-11-13. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC). Dynamic Stability Control Unit (DSC) Aborted when Programming Vehicle. If termination of vehicle programming occurs due to: A. Undervoltage (when the vehicle is connected to an approved battery charger/power supply) B. Lost connection to the server C. Termination by the control module D. Termination by ISTA/P E. ICOM connector removed/falls out Then the DSC module may no longer communicate when connected to ISTA/D or ISTA/P. As a result, the DSC module cannot be reprogrammed. DSC software
6605142018-11-13. Service bulletin. EQUIPMENT. Speed Limit Information Does Not Work. Speed limit information (SLI) is not displayed in the Kombi or the Head-Up Display (HUD). This only affects the specific VINs (vehicle identification numbers) listed below. The vehicle was built incorrectly (without option 8TH).
6516142018-11-13. Service bulletin. EQUIPMENT. Central Information Display Intermittently Dimming or Flashing Off/On. Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID.
6502142018-11-13. Service bulletin. EQUIPMENT. Headunit High Is Constantly Resetting. After connecting a mobile device via Bluetooth, the Headunit High (HU-H) constantly resets. This is because the mobile device paired/connected to the vehicle contains one or more emails with 30 or more recipients. Note: In this situation, a reset is when the HU-H shuts down and then turns back on. CAUSE Software error in the HU-H.
5115142018-11-13. Service bulletin. EQUIPMENT. Service Action: Replace Center Console Lock Cylinder. The center console lock cylinder is loose. Manufacturing tolerances of the center console lock cover cap may cause it to become loose or missing. AFFECTED VEHICLES This Service Action involves F01, F02, F06, F07, F12 and F13 vehicles produced from March 7, 2014 to April 23, 2014. First check if a Service Action label with a code number 688 is already attached to the B-pillar. If a code number 688 has been punched out, the Service Action has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.
8401142018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL. ConnectedDrive/BMW Assist System Information and Availability. ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.