WenmarOpen by Wenmar Pro

Service bulletins for the 2014 BMW 528i

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

350 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Driver assistance are shown. Show all

Bulletins, newest first
B6504142022-12-12. Service bulletin. LANE DEPARTURE; UNKNOWN OR OTHER; AIR BAGS; SEATS:BARRIERS; BACK OVER PREVENTION. According to the customer, the airbag warning light was on, but it may not be illuminated when the vehicle arrives in the workshop. 1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Front passenger seat occupancy detection transmitting fault(moisture)" is stored. The fault may or may not currently be present.
B3405172020-04-20. Service bulletin. BACK OVER PREVENTION; SERVICE BRAKES, HYDRAULIC; WHEELS; POWER TRAIN. TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs.
B6601152018-12-17. Service bulletin. BACK OVER PREVENTION. Surround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller.
B6609162018-12-10. Service bulletin. VEHICLE SPEED CONTROL:CRUISE CONTROL; EQUIPMENT; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL. """Collision Warning Failed"" or ""Pedestrian Warning Failed"" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the ""green lines"""
6608142018-11-26. Service bulletin. BACK OVER PREVENTION. Side View Camera Does Not Display Picture. The side view camera does not display a picture: z After engaging reverse gear z Activating the side view camera via the switch on the center console near the gear shift CAUSE z Water (moisture) entering the cable assembly, causing corrosion on the pins in the connector(s) at the camera(s) z Poor cable connection to the camera(s)
3405142018-11-13. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC). Dynamic Stability Control Unit (DSC) Aborted when Programming Vehicle. If termination of vehicle programming occurs due to: A. Undervoltage (when the vehicle is connected to an approved battery charger/power supply) B. Lost connection to the server C. Termination by the control module D. Termination by ISTA/P E. ICOM connector removed/falls out Then the DSC module may no longer communicate when connected to ISTA/D or ISTA/P. As a result, the DSC module cannot be reprogrammed. DSC software
6604142018-11-13. Service bulletin. FORWARD COLLISION AVOIDANCE. Front Collision Warning Check Control Message Displayed in CID. Occasionally while driving, a check control message (CCM) for Front Collision Warning is displayed in the Central Information Display (CID). This message is cleared from the CID by clicking on "OK" using the iDrive controller. CAUSE The KAFAS (camera-based driver support system) camera is affected by environmental conditions such as: * Direct sunlight (sunrise or sunset) * Rain * Fog * Dirt * Snow * Ice * High interior temperatures (may also cause a CCM to be displayed upon starting the vehicle) ?? Fault code 0x800AC0 - KAFAS camera switch off due to over temperature The pictures below show the direct sunlight causing the CCM: INFORMATION This is the current text in the Owner's Manual for the Front Collision Warning (FCW): The system may not be fully functional in the following situations: * In heavy fog, rain, sprayed with water or snowfall * In tight curves * If the driving stability control systems are limited or deactivated: for example, the DSC is off. * If the camera view field of the front windshield is dirty or covered. * Up to 10 seconds after the start of the engine, via the Start/Stop knob. Direct sunlight will be added as one of the causes for the FCW CCM.
B6613162018-11-05. Service bulletin. LANE DEPARTURE; ELECTRICAL SYSTEM:SOFTWARE. Erroneous Blind Spot Warnings. Orange triangle warning indicator, on exterior mirror, sporadically appears when there is no vehicle in warning zone. Control unit software error.
B6621162018-11-05. Service bulletin. ENGINE; LANE DEPARTURE: SENSING SYSTEM: OTHER; SERVICE BRAKES. KAFAS CAMERA-BASED ASSISTANCE SYSTEM LIMITS. INFORMATION The situations described above may all be caused by known limitations of the system such as: Dirty windshield Incomplete calibration process Unsuccessful calibration Restricted visibility- weather conditions or parked vehicles Missing lamps on target vehicle Non-standard vehicle exterior surfaces Insufficient ambient lighting Abrupt motion of target vehicle.
B6608142018-07-16. Service bulletin. BACK OVER PREVENTION. Side View Camera Does Not Display Picture.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.