WenmarOpen by Wenmar Pro

Service bulletins for the 2016 BMW 435i

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

325 on file from NHTSA, as of 2026-10-19.

By type

By component

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
B6130172018-11-26. Service bulletin. ELECTRICAL SYSTEM. RAIN/LIGHT SENSOR (RLS): OIL LEAKAGE FROM GEL PAD. ??Oil leaking from the Rain/Light Sensor (RLS). Note: This oil serves as a separation medium between the RLS mounting gel pad and the windscreen. The oil ensures damage free disassembly in case of repair. CAUSE The oil that serves as the separation medium of the Rain/Light Sensor (RLS) gel pad and the windscreen leaks out. Expose the Rain/Light Sensor (RLS) and properly clean the area of all oily residue. Note: The separating oil usually leaks only once from the pad at the RLS. Due to the small oil quantity in the gel pad, additional oil leakage is not plausible. Leaking oil does not impair the function of the RLS.
B6124172018-11-26. Service bulletin. STEERING: STEERING WHEEL/HANDLE BAR; ELECTRICAL SYSTEM. "?STEERING WHEEL BUTTONS DO NOT FUNCTION RELIABLY. ? Sporadic or continuous malfunction of multifunction steering wheel buttons ? CC Message ""Cruise control without function"" displayed ? Sporadic or continuous malfunction of shift paddles Frictional corrosion on connector line (wiring harness) between switch cluster and steering wheel"
B6609152018-11-13. Service bulletin. ELECTRICAL SYSTEM; LANE DEPARTURE; FORWARD COLLISION AVOIDANCE. Sporadically, a CCM (Check Control Message) is displayed advising that the Camera-based Driver Assistant system has failed. During this failure, all KAFAS (Camera-based driver assistance systems) system functionalities are inoperative. The affected functionalities are: Pedestrian Detection Front Collision Warning Lane Departure Warning Speed Limit Info (if equipped) Note: The system is functional after the interior temperature has cooled down or by cycling the ignition off and on again.
B6212152018-11-13. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Instrument Cluster Outside Temperature Display Implausible. INFORMATION This service information bulletin provides technical, diagnostic and/or repair-related information. Eligible and Covered Work/Repairs To submit a claim for the repair of a verified defect in materials or workmanship, please following the established and applicable warranty policy and procedures together with the using corresponding defect code and labor operations provided in the KSD2.
B6509152018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL. HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
B6406132018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; EQUIPMENT:APPLIANCE:AIR CONDITIONER. A/C Cooling: Intermittent Reduction of Air Flow. Customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than 30 minutes. INFORMATION Possibility of reproducing this situation is improved by the following conditions ? High outside ambient temperature ? High humidity Note: It is very difficult to duplicate this issue. The fault may be reproduced under the following conditions: ? Air-conditioning system switched on ? Driving Experience switch NOT set to Eco Pro ? Slower fan speeds ? Temperature setting below 68°F (20°C) ? Trip duration at least 30 minutes ? Outside temperature above 68°F (20°C) NOTE: After parking the vehicle or switching off the air-conditioning system for at least 20 minutes, the symptom disappears (ice melts off evaporator and puddles under the car from the A/C drains.). Evaporator starts to freeze up due to the position of the evaporator temperature sensor.
B8404152018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. "The illumination (back lighting) for the E-Call (Emergency/SOS call) button in the FZD (sunroof module) overhead console does not work. This picture shows the E-Call button illumination (back lighting) not working. Note: Pressing the E-Call button will start an SOS call, even though the back lighting is not working.This picture shows E-Call illumination (back lighting) working. AFFECTED VEHICLES This Service Action involves the F34 (3 Series Gran Turismo) and F36 (4 Series Gran Coupe) models, produced from 7/27/2015 to 7/30/2015. Please perform it the next time this vehicle comes to your workshop. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. Missing wiring harness for the illumination of the E-Call button."
B6606152018-11-13. Service bulletin. ELECTRICAL SYSTEM. Sporadic Check Control Messages of the Driver Assistance System. Sporadically, a CCM (Check Control Message) is displayed advising that the Camera-based Driver Assistant system has failed. This is due to the vehicle interior reaching very high temperatures. During this failure, all KAFAS (Camera-based driver assistance systems) system functionalities are inoperative. The affected functionalities are: Pedestrian Detection Front Collision Warning Lane Departure Warning Speed Limit Info (if equipped) The following fault code is stored in the KAFAS control unit: 0x800AC0 - Switching off due to excess temperature Note: The system is functional after the interior temperature has cooled down or by cycling the ignition off and on again. Incorrect calibration of the temperature sensor in the KAFAS camera.
B6126142018-11-13. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:HORN. "Horn(s) Fail to Work. While trying to activate the horn, one or both horns fail to work. One or more of the following fault codes can be stored in the FEM: ? ""8044A3 - Wiring, horn short circuit to earth"" ? ""8044A4 - Wiring, horn short circuit to positive"" ? ""8044A5 - Wiring, horn relay is defective or short circuit to positive"" Water has entered the horn and caused it to fail internally (shorted out)."
B6104152018-11-13. Service bulletin. VISIBILITY:REAR WINDOW WIPER/WASHER; ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:HORN. Horn Blows when Unlocking Vehicle. The customer states that the vehicle horn sounds briefly when unlocking the vehicle or opening the door. In some cases, the washers spray briefly on the windshield. Front Electronics Module (FEM) software error
B6103152018-11-13. Service bulletin. ELECTRICAL SYSTEM. General Electrical Systems Technical Service. Various Check Control Messages Caused by Shorted K-CAN. The customer states that one or more of the following CC messages are displayed: ? 627 - Steering behavior: Drive moderately ? 070 - Steering: Drive moderately ? 765 - Rear-end collision restricted ? 850 - Pedestrian warning restricted ? 236 - Driving stabilization: Drive moderately ? 299 - SOS call system failure ? 042 - Brake system: Drive moderately After performing a vehicle test, one or more of the following fault codes are stored: ? ACSM - C9549A Message faulty (seat memory), ACSM receiver, driver's seat module transmitter ? FEM - D91DE0 No message, receiver FEM, transmitter TMSL ? FEM - D91EE5 No message, receiver FEM, passenger seat module transmitter ? ACSM - C9540C Message missing, receiver ACSM, transmitter FEM ? TMSL - D95402 Message missing, receiver TMSL, transmitter FEM ? KOMBI - E11454 No message, receiver KOMBI, transmitter REM ? FEM - D91DE6 No message, receiver FEM, transmitter TMSL ? TMSR - D99401 Message missing, receiver TMSR, transmitter FEM ? TMSR - D99402 Message missing, receiver TMSR, transmitter FEM ? FEM - 8041BA AHL system faulty ? FEM - D916C3 No message, receiver FEM, transmitter TCB ? ZBE - E2D403 No message, receiver CON, transmitter FEM-ZGM ? TRSVC - CA9428 Message incorrect, receiver TRSVC, transmitter PDC-REM ? TMSL- D95401 Message missing, receiver TMSR, transmitter FEM ? HU-H - S0397 MOST configuration was not stored ? TCB - E1445F KCAN2 or KCAN4: Line fault/electrical fault ? FEM - 8041B6 LWR faulty ? REM - E58468 Body CAN2; communication fault ? TRSVC - CA9427 Message incorrect, receiver all around vision camera, transmitter PDC/REM ? FEM - D91CEC Message missing, receiver FEM, transmitter REM Shorted KCAN wiring under driver or passenger seat.
1240142018-11-13. Service bulletin. ENGINE; ELECTRICAL SYSTEM. "SUBJECT N55 and NPOW: DME Fault 102001, Air Mass Too High, Sets in ECO PRO Mode. The Service Engine Soon light (MIL) comes on while driving at moderate to highway speeds in ECO PRO with the ""Coasting"" feature selection active. z Fault 102001: Air mass, plausibility: Air mass too high is stored in the DME BMW Power Kit DME software"
1204152018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.
B8403152018-11-05. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. "HU-B: Bluetooth Connection Fails Sporadically. The Bluetooth system works intermittently. One or more of the following scenarios may occur: Bluetooth pairing is not possible - display shows ""Please wait"" Unable to select the check box to activate Bluetooth Device does not reconnect to the vehicle after a key cycle Audio interference noise is heard listening to iPod etc. When trying to access the user manual, the display shows ""Please wait"" Incorrect software installed in the HU-B (Headunit Basic)."
B6104152018-11-05. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT; ELECTRICAL SYSTEM:HORN; VISIBILITY:WINDSHIELD WIPER/WASHER. Horn Blows when Unlocking Vehicle. The customer states that the vehicle horn sounds briefly when unlocking the vehicle or opening the door. In some cases, the washers spray briefly on the windshield. Front Electronics Module (FEM) software error
B1221142018-11-05. Service bulletin. FUEL SYSTEM, OTHER:STORAGE:FUEL GAUGE SYSTEM; ELECTRICAL SYSTEM:SOFTWARE; FUEL SYSTEM, GASOLINE. Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
B6103142018-11-05. Service bulletin. ELECTRICAL SYSTEM. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can occur. The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
B1221142018-11-05. Service bulletin. ELECTRICAL SYSTEM. ?SI B12 21 14May 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated April 2015. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
6103142018-11-05. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE ? The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
1221142018-11-05. Service bulletin. ENGINE; ELECTRICAL SYSTEM. SI B12 21 14February 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated December 2014. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: z FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
B6618162018-11-05. Service bulletin. ELECTRICAL SYSTEM. INFORMATION ON THE OPERATION OF THE SMART OPENER. INFORMATION ON THE OPERATION OF THE SMART OPENER MODEL F07 (5 Series Gran Turismo) F10 (5 Series) F12 (6 Series Convertible) F13 (6 Series Coupe) F15 (X5) F16 (X6) F22 (2 Series Coupe) F23 ( 2 Series Convertible) F25 (X3) F26 (X4) F30 (3 Series Sedan) F31 (3 Series Wagon) F32 (4 Series Coupe) F33 (4 Series Convertible) F34 (3 Series Gran Turismo) F36 (4 Series Gran Coupe) F48 (X1) F80 (M3 Sedan) F82 (M4 Coupe) F83 (M4 Convertible) F85 (X5 M) F86 (X6 M) G12 (7 Series) I01 (i3 Series) Vehicles with option code SA-0322 (Comfort Access) without M-Sport trim INFORMATION The smart opener (Contactless tailgate) operates as described below: Ignition key must be within 3 feet behind the vehicle, clear from any interference like a smartphone The customer must be at least an arms-length behind the vehicle Kick your foot forwards & backwards under the vehicle in one quick movement The taillights flash confirming that the trunk will open The trunk then successfully opens For more information an instructional video can be viewed which demonstrates the operation. Thanks to BMW of Tenafly for providing the video. tinyurl.com/Autotrunk1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016 Page 2 of 2 WARRANTY INFORMATION Not applicable. [ Copyright (c)2016 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016
B6523162018-11-05. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. ?AUDIO VOLUME NOT RESTORED AFTER MSA STOP, ENTRY HEAD UNIT. Volume of audio system (when set to near maximum) is reduced when Auto Start-Stop (MSA) stop occurs and is not restored upon automatic engine restart. This is normal system behavior - serves to protect the head unit, battery drain and avoidance of incremental leaps in the loudness. The loudness is reduced to 2/3 of maximum and is not restored. Note: Air conditioning output is also reduced upon MSA stop and is not restored for similar reasons.
B8404162018-11-05. Service bulletin. ELECTRICAL SYSTEM. SOS MALFUNCTION DISPLAYED. An SOS malfunction is seen in the Kombi. When pressing the E-Call/SOS button in the overhead console, nothing happens. Fault code B7F33C (internal ECU error) is stored in the Telematics control unit (ATM/TCB2). There are 2 known causes for this failure. They are as follows: Software file missing from the ATM/TCB2 control module Water leak at shark-fin leading to corrosion in the ATM/TCB2 control module
B6308162018-11-05. Service bulletin. EXTERIOR LIGHTING:TURN SIGNAL; ELECTRICAL SYSTEM. TURN SIGNAL - INTERMITTENTLY FLASHES AT FASTER RATE. Turn signal, intermittently, flashes at faster rate or not at all. Software error in FEM (Front Electronics Module)
B0703142018-11-05. Service bulletin. ELECTRICAL SYSTEM. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits This Service Information bulletin supersedes SI B07 03 14 dated October 2015.. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.