Service bulletins for the 2014 BMW 435i
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
391 on file from NHTSA, as of 2026-10-19.
By type
By component
| 123314 | 2018-11-13. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat. |
|---|---|
| 840214 | 2018-11-13. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. ConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause. |
| 660414 | 2018-11-13. Service bulletin. FORWARD COLLISION AVOIDANCE. Front Collision Warning Check Control Message Displayed in CID. Occasionally while driving, a check control message (CCM) for Front Collision Warning is displayed in the Central Information Display (CID). This message is cleared from the CID by clicking on "OK" using the iDrive controller. CAUSE The KAFAS (camera-based driver support system) camera is affected by environmental conditions such as: * Direct sunlight (sunrise or sunset) * Rain * Fog * Dirt * Snow * Ice * High interior temperatures (may also cause a CCM to be displayed upon starting the vehicle) ?? Fault code 0x800AC0 - KAFAS camera switch off due to over temperature The pictures below show the direct sunlight causing the CCM: INFORMATION This is the current text in the Owner's Manual for the Front Collision Warning (FCW): The system may not be fully functional in the following situations: * In heavy fog, rain, sprayed with water or snowfall * In tight curves * If the driving stability control systems are limited or deactivated: for example, the DSC is off. * If the camera view field of the front windshield is dirty or covered. * Up to 10 seconds after the start of the engine, via the Start/Stop knob. Direct sunlight will be added as one of the causes for the FCW CCM. |
| 651614 | 2018-11-13. Service bulletin. EQUIPMENT. Central Information Display Intermittently Dimming or Flashing Off/On. Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID. |
| 650214 | 2018-11-13. Service bulletin. EQUIPMENT. Headunit High Is Constantly Resetting. After connecting a mobile device via Bluetooth, the Headunit High (HU-H) constantly resets. This is because the mobile device paired/connected to the vehicle contains one or more emails with 30 or more recipients. Note: In this situation, a reset is when the HU-H shuts down and then turns back on. CAUSE Software error in the HU-H. |
| 612114 | 2018-11-13. Service bulletin. FUEL SYSTEM, OTHER:DELIVERY:FUEL PUMP. Service Action: Check Wiring Harness for Electric Fuel Pump. The wiring harness for the electric fuel pump may not have been routed or secured correctly. In unfavorable conditions, the wiring harness may come into contact with sharp edges on the fuel pump access cover. Continuous contact with the access cover can damage the wiring harness, which leads to fault codes stored and CC messages displayed. AFFECTED VEHICLES This Service Action involves F33 models according to Vehicle Identification Number (VIN) selection. First check if a Service Action label with a code number 692 is already attached to the B-pillar. If a code number 692 has been punched out, the Campaign has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader. Incorrect routing of the harness for the electric fuel pump. |
| 611514 | 2018-11-13. Service bulletin. SEATS; ELECTRICAL SYSTEM. Neck Warmer Not Working. The neck warmer function (NWR) is not working and the LEDs in the NWR control element do not light up. The neck warmer functions properly after switching the ignition off and on again. The control unit is located under the rear seat bottom, as shown in the photo, and is clipped into place.SMFA (Seat Module Drivers) fault code E44C21: "LIN bus: Neck warmer control unit does not function" is stored. Note: For the first time, the neck warmer is available as optional equipment (SA4NH) in the Convertible. The neck warmer reduces cold drafts that a customer feels on his or her neck when driving with the roof open. Warm air is guided over the seat. The operation differs depending on whether the roof is open or closed. Neck warmer software application error. |
| 610314 | 2018-11-13. Service bulletin. ELECTRICAL SYSTEM. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut |
| 840314 | 2018-11-13. Service bulletin. ELECTRICAL SYSTEM. iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants. |
| 010414 | 2018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. External Engine Oil Leaks and Repairs. During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can cause the appearance of a more severe oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, e.g., oil filter changes, "engine oil top-offs," etc. If this visual appearance of accumulated oil on the engine assembly as an "active leak" is misinterpreted, unnecessary gasket repairs/replacements will result. Specifically, our analysis of the claim-related data for vehicles equipped with the engines noted in this bulletin is showing an above-average number of engine gasket repair/replacement claim submissions. The purpose of this bulletin is to provide your workshop with information and a procedure that will help in identifying engine oils leaks that do and do not require a repair. |
| 660714 | 2018-11-13. Service bulletin. VISIBILITY; ELECTRICAL SYSTEM. Top Rear Side View Camera Control Unit Rattles While Driving. While driving, a rattling-type noise is heard coming from the lower windshield area up behind the instrument panel (driver's side). CAUSE The TRSVC (Top Rear Side View Camera) control module support bracket is loose. |
| 630514 | 2018-11-13. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING:HEADLIGHTS; EXTERIOR LIGHTING. "Adaptive Headlight Malfunction in Cold Weather. * In very cold weather conditions (32ºF or below) with the light switch in the automatic position, the CCM (Check Control Message) ""Adaptive headlight malfunction"" is displayed. * When the CC message is displayed, all the lights continue to function. * When switching the headlights to high beam and the headlight unit is cold, the mechanism inside the headlight is too stiff to move. Software error in TMS 3 (headlight driver module AHL, xenon headlight)" |
| 512113 | 2018-11-13. Service bulletin. VISIBILITY; STRUCTURE:BODY:DOOR. Door Mirror Wind/Whistle Noise. Whistling noise from front area of the front door mirror when driving at highway speeds CAUSE There is an air gap between the door mirror cap and the turn signal housing in the mirror. |
| 840114 | 2018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL. ConnectedDrive/BMW Assist System Information and Availability. ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle. |
| 840613 | 2018-11-13. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL. iPhone Charging Status Constantly Switches On and Off. INFORMATION Do not replace any other parts! Advise the customer that he/she must use one of the following: * The original Apple iPhone/iPOD USB cable that came with the device * A BMW supplied iPhone/iPOD USB adapter cable PARTS INFORMATION |
| 652313 | 2018-11-13. Service bulletin. EQUIPMENT:ELECTRICAL. Headunit-High: Navigation Road Map Installation After Replacement. When replacing the HU-H, the road map database version that was in the defective HU-H must be installed in the new HU-H. |
| 640713 | 2018-11-13. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR; ENGINE AND ENGINE COOLING. Service Action: Replace Blower Motor Regulator. The blower motor regulator has an internal fault; after starting the engine, there may be a delay of up to a minute before the blower motor comes on CAUSE Faulty blower motor regulator (output stage) |
| 640114 | 2018-11-13. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Noise from Heating and Air Conditioner. There is an intermittent whirring noise from the IHKA system when the engine is under load between 2,000 and 3,000 rpm, and sometimes at approximately 5,000 rpm. CAUSE Vibrations from the A/C low-pressure hose are resonating into the heating and air conditioning system. |
| 630614 | 2018-11-13. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS; EQUIPMENT. One or Both Headlights Are Aimed Downwards. The customer may experience one or more of the following complaints: * One or both headlights are aimed significantly too low (jammed lower limit). * No reference run is visible on the affected headlight when the ignition is turned on and the light switch is in the auto position. * No CCM (Check Control Message) is displayed when a headlight is faulty. CAUSE * TMS-3 (Headlight driver module AHL) coding error * Defective mechanism inside the headlight |
| 540213 | 2018-11-13. Service bulletin. VISIBILITY:SUN/MOON ROOF ASSEMBLY. ?Sunroof Gets Stuck or Moves in Small Steps. During opening or closing the sunroof, one or more of the following situations may occur: 1. The sunroof becomes stuck 2. One-touch open and close no longer works 3. The sunroof moves in small steps. CAUSE Software error in the sunroof control module (FZD) Some or all of the following fault codes may be stored: 0x030212 - SHD: Activation timeout, no block recognition 0x030214 - SHD: Zero position passed, loss of calibration 0x030215 - SHD: Invalid characteristic curve, not normalized 0x030216 - SHD: 90% motor temperature threshold exceeded 0x030217 - SHD: Motor operation interrupted by overheating 0x030218 - SHD: Motor does not start due to overvoltage or undervoltage 0x030219 - SHD: Errors in the checksum coding 0x03021C - SHD: Not initialized due to invalid marginal conditions (motor driver) 0x030220 - SHD: System not normalized 0x801A02 - Coding: Control unit is not coded. |
| 510714 | 2018-11-13. Service bulletin. ELECTRICAL SYSTEM; VISIBILITY. Noise from Rearview Mirror. Rattling noises can be heard from the rearview mirror when driving. CAUSE The mirror electrical connector is loose in the mirror base. |
| 510514 | 2018-11-13. Service bulletin. EQUIPMENT; STRUCTURE. Service Action: Remove and Discard Water Drain Plugs from E-Box. Water leaks into the cabin due to clogged drain plugs in the E-boxes. CAUSE The drain plug slots are too small and clog. |
| 122513 | 2018-11-13. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. Reduced Engine and Air-Conditioning Performance. When driving with high outside ambient temperatures, repeated stop and go, or high load operation over longer distances, the engine performance can be reduced. The air-conditioning system blower output may also be reduced, and in some circumstances the compressor is switched off. There could be any of the following faults stored depending on the conditions present at the time. DME * Fault 1A2108: Electric fan, self-diagnosis, interval stage 1: Minor fan fault EGS (also possibly set) * Fault 421722: DME/DDE interface: Forced upshift due to thermal engine protection request IHKA (possibly set without DME or EGS faults) * Fault 801224: Air conditioning compressor: Shut-down due to excess pressure in refrigerant circuit * Fault 801228: Blower output stage: Blower output reduction due to power management The Service Engine Soon lamp (MIL) would not be illuminated in these situations. 1. A DME software error in the control of the 850W electric fan over-boost or high speed function. 2. The electric cooling fan design was not robust enough for continuous over-boost or high speed operation. |
| 653009 | 2018-11-13. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Enabling Code FSC/SWT - Enabling the Navigation System Map at QC1. The navigation system is inoperative unless the map is enabled during the QC1 Pre-Delivery Check. INFORMATION New vehicles come equipped with a navigation road map that must be enabled via an enable code (FSC). This process is part of the QC1 Pre-Delivery Check performed with the ISID (ISTA Diagnosis). IMPORTANT: There is no programming involved! |
| 652513 | 2018-11-13. Service bulletin. ELECTRICAL SYSTEM. "ConnectedDrive/BMW ASSIST Features Are Inoperative. ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST ""My Info"" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle." |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.