WenmarOpen by Wenmar Pro

Service bulletins for the 2016 BMW 320i

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

353 on file from NHTSA, as of 2026-10-19.

By type

By component

Only bulletins with component: Driver assistance are shown. Show all

Bulletins, newest first
B3405172020-04-20. Service bulletin. BACK OVER PREVENTION; SERVICE BRAKES, HYDRAULIC; WHEELS; POWER TRAIN. TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs.
B6601152018-12-17. Service bulletin. BACK OVER PREVENTION. Surround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller.
B6103152018-12-10. Service bulletin. FUEL SYSTEM, GASOLINE; STEERING; STRUCTURE; EQUIPMENT; WHEELS; ELECTRICAL SYSTEM; FORWARD COLLISION AVOIDANCE; LANE DEPARTURE. Various Check Control Messages Caused by Shorted K-CAN This Service Information bulletin supersedes SI B61 03 15 dated April 2016. The customer states that one or more of the following CC messages are displayed: 627 - Steering behavior:Drive moderately 070 - Steering: Drive moderately 765 - Rear-end collision restricted 850 - Pedestrian warning restricted 236 - Driving stabilization: Drive moderately 299 - SOS call system failure 042 - Brake system: Drive moderately After performing a vehicle test, one or more of the following fault codes are stored: ACSM - C9549A Message faulty (seat memory), ACSM receiver, driver's seat module transmitter FEM - D91DE0 No message, receiver FEM, transmitter TMSL FEM - D91EE5 No message, receiver FEM, passenger seat module transmitter ACSM - C9540C Message missing, receiver ACSM, transmitter FEM TMSL - D95402 Message missing, receiver TMSL, transmitter FEM KOMBI - E11454 No message, receiver KOMBI, transmitter REM FEM - D91DE6 No message, receiver FEM, transmitter TMSL TMSR - D99401 Message missing, receiver TMSR, transmitter FEM TMSR - D99402 Message missing, receiver TMSR, transmitter FEM FEM - 8041BA AHL system faulty FEM - D916C3 No message, receiver FEM, transmitter TCB ZBE - E2D403 No message, receiver CON, transmitter FEM-ZGM TRSVC - CA9428 Message incorrect, receiver TRSVC, transmitter PDC-REM TMSL- D95401 Message missing, receiver TMSR, transmitter FEM HU-H - S0397 MOST configuration was not stored TCB - E1445F KCAN2 or KCAN4: Line fault/electrical fault FEM - 8041B6 LWR faulty REM - E58468 Body CAN2; communication fault TRSVC - CA9427 Message incorrect, receiver all around vision camera, transmitter PDC/REM FEM - D91CEC Message missing, receiver FEM, transmitter REM Shorted K-CAN wiring under driver or passenger seat Shorted K-CAN2 wires were shorted between the left side trunk trim panel and the body of the vehicle Shorted K-CAN in left rear wheel well area Shorted K-CAN under center console trim Shorted K-CAN under A-Pill
B6609162018-12-10. Service bulletin. VEHICLE SPEED CONTROL:CRUISE CONTROL; EQUIPMENT; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL. """Collision Warning Failed"" or ""Pedestrian Warning Failed"" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the ""green lines"""
B6607162018-12-10. Service bulletin. LANE DEPARTURE. Erroneous Lane Change Warning. While driving, the Lane Change Warning (Blind Spot Detection) is illuminated erroneously on either outside mirror (orange triangle) when no other vehicles are around. CAUSE F30 - Install the correct sensor frame F34 - Program the vehicle using ISTA/P 3.58.0 or higher.
B6605152018-11-05. Service bulletin. LANE DEPARTURE: LANE KEEP: STEERING ASSIST. Parking Maneuvering Assistant and Park Distance Control Failure. After activating the PMA (Parking Maneuvering Assistant) or PDC (Park Distance Control), the system stops functioning and a CCM (Check Control Message) is displayed advising the driver of the failure. The following fault code is stored in the PMA control unit 0x481E4D - PMA control unit internal, internal ASIC fault Software error in the PMA control unit Affected I-Level: F2x from F020-15-03-500 F3x from F020-15-07-500
B6608142018-07-16. Service bulletin. BACK OVER PREVENTION. Side View Camera Does Not Display Picture.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.