Service bulletin B660716
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10151272 |
| Published by NHTSA | 2018-12-10 |
| Manufacturer's number | B660716 |
| Manufacturer's date | 2016-04-01 |
| NHTSA component | LANE DEPARTURE |
NHTSA's summary
Erroneous Lane Change Warning. While driving, the Lane Change Warning (Blind Spot Detection) is illuminated erroneously on either outside mirror (orange triangle) when no other vehicles are around. CAUSE F30 - Install the correct sensor frame F34 - Program the vehicle using ISTA/P 3.58.0 or higher.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Driver assistance
| BMW 320I | 2013, 2014, 2015, 2016 |
|---|---|
| BMW 328D | 2014, 2015, 2016 |
| BMW 328I | 2012, 2013, 2014, 2015, 2016 |
| BMW 330E | 2016 |
| BMW 335I | 2012, 2013, 2014, 2015, 2016 |
| BMW 340I | 2016 |
| BMW ACTIVE HYBRID 3 | 2013 |
| BMW ACTIVE HYBRID 3 | 2014, 2015 |
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| B650414 | 2022-12-12. Service bulletin. According to the customer, the airbag warning light was on, but it may not be illuminated when the vehicle arrives in the workshop. 1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Front passenger seat occupancy detection transmitting fault(moisture)" is stored. The fault may or may not currently be present. |
|---|---|
| B340517 | 2020-04-20. Service bulletin. TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs. |
| B660115 | 2018-12-17. Service bulletin. Surround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller. |
| B610315 | 2018-12-10. Service bulletin. Various Check Control Messages Caused by Shorted K-CAN This Service Information bulletin supersedes SI B61 03 15 dated April 2016. The customer states that one or more of the following CC messages are displayed: 627 - Steering behavior:Drive moderately 070 - Steering: Drive moderately 765 - Rear-end collision restricted 850 - Pedestrian warning restricted 236 - Driving stabilization: Drive moderately 299 - SOS call system failure 042 - Brake system: Drive moderately After performing a vehicle test, one or more of the following fault codes are stored: ACSM - C9549A Message faulty (seat memory), ACSM receiver, driver's seat module transmitter FEM - D91DE0 No message, receiver FEM, transmitter TMSL FEM - D91EE5 No message, receiver FEM, passenger seat module transmitter ACSM - C9540C Message missing, receiver ACSM, transmitter FEM TMSL - D95402 Message missing, receiver TMSL, transmitter FEM KOMBI - E11454 No message, receiver KOMBI, transmitter REM FEM - D91DE6 No message, receiver FEM, transmitter TMSL TMSR - D99401 Message missing, receiver TMSR, transmitter FEM TMSR - D99402 Message missing, receiver TMSR, transmitter FEM FEM - 8041BA AHL system faulty FEM - D916C3 No message, receiver FEM, transmitter TCB ZBE - E2D403 No message, receiver CON, transmitter FEM-ZGM TRSVC - CA9428 Message incorrect, receiver TRSVC, transmitter PDC-REM TMSL- D95401 Message missing, receiver TMSR, transmitter FEM HU-H - S0397 MOST configuration was not stored TCB - E1445F KCAN2 or KCAN4: Line fault/electrical fault FEM - 8041B6 LWR faulty REM - E58468 Body CAN2; communication fault TRSVC - CA9427 Message incorrect, receiver all around vision camera, transmitter PDC/REM FEM - D91CEC Message missing, receiver FEM, transmitter REM Shorted K-CAN wiring under driver or passenger seat Shorted K-CAN2 wires were shorted between the left side trunk trim panel and the body of the vehicle Shorted K-CAN in left rear wheel well area Shorted K-CAN under center console trim Shorted K-CAN under A-Pill |
| B660916 | 2018-12-10. Service bulletin. """Collision Warning Failed"" or ""Pedestrian Warning Failed"" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the ""green lines""" |
| 270212 | 2018-12-03. Service bulletin. "DSC Warning Light Is On. The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for ""Chassis Control System failure."" One or more of the following fault codes are stored: DSC: ??D36D44 - Signal error longitudinal torque distribution (LMV) ??48097D - Transfer Case clutch position open CAUSE Software calibration error in the LMV" |
| 660814 | 2018-11-26. Service bulletin. Side View Camera Does Not Display Picture. The side view camera does not display a picture: z After engaging reverse gear z Activating the side view camera via the switch on the center console near the gear shift CAUSE z Water (moisture) entering the cable assembly, causing corrosion on the pins in the connector(s) at the camera(s) z Poor cable connection to the camera(s) |
| 340514 | 2018-11-13. Service bulletin. Dynamic Stability Control Unit (DSC) Aborted when Programming Vehicle. If termination of vehicle programming occurs due to: A. Undervoltage (when the vehicle is connected to an approved battery charger/power supply) B. Lost connection to the server C. Termination by the control module D. Termination by ISTA/P E. ICOM connector removed/falls out Then the DSC module may no longer communicate when connected to ISTA/D or ISTA/P. As a result, the DSC module cannot be reprogrammed. DSC software |
| 660414 | 2018-11-13. Service bulletin. Front Collision Warning Check Control Message Displayed in CID. Occasionally while driving, a check control message (CCM) for Front Collision Warning is displayed in the Central Information Display (CID). This message is cleared from the CID by clicking on "OK" using the iDrive controller. CAUSE The KAFAS (camera-based driver support system) camera is affected by environmental conditions such as: * Direct sunlight (sunrise or sunset) * Rain * Fog * Dirt * Snow * Ice * High interior temperatures (may also cause a CCM to be displayed upon starting the vehicle) ?? Fault code 0x800AC0 - KAFAS camera switch off due to over temperature The pictures below show the direct sunlight causing the CCM: INFORMATION This is the current text in the Owner's Manual for the Front Collision Warning (FCW): The system may not be fully functional in the following situations: * In heavy fog, rain, sprayed with water or snowfall * In tight curves * If the driving stability control systems are limited or deactivated: for example, the DSC is off. * If the camera view field of the front windshield is dirty or covered. * Up to 10 seconds after the start of the engine, via the Start/Stop knob. Direct sunlight will be added as one of the causes for the FCW CCM. |
| B660515 | 2018-11-05. Service bulletin. Parking Maneuvering Assistant and Park Distance Control Failure. After activating the PMA (Parking Maneuvering Assistant) or PDC (Park Distance Control), the system stops functioning and a CCM (Check Control Message) is displayed advising the driver of the failure. The following fault code is stored in the PMA control unit 0x481E4D - PMA control unit internal, internal ASIC fault Software error in the PMA control unit Affected I-Level: F2x from F020-15-03-500 F3x from F020-15-07-500 |