WenmarOpen by Wenmar Pro

Service bulletins for the 2014 BMW 320i

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

486 on file from NHTSA, as of 2026-10-19.

By type

By component

Bulletins, newest first
1305142018-11-26. Service bulletin. ENGINE. . INFORMATION To properly diagnose the customer's complaint, the applicable test plan for the misfire faults stored in the DME must be performed to avoid repeat repairs. If a misfire fault is not stored in the DME memory and an engine related drivability complaint is received, follow the path below to manually start the misfire test plan (AT1214_TVD4_MISFIRE_20): 1. Perform a vehicle test. 2. Select "Function Structure." 3. Select "01 Engine." 4. Select "Engine electronics MEVD." 5. Select "Misfire detection." 6. Follow the steps in the test plan and select "Basic check (start)" first. Do not select "Additional check" at this time. 7. If the result of the "Basic check" indentifies a fuel system component failure, replace the identified component. If the result of the "Basic check" test plan was inconclusive, go to step 7. After the component replacement, perform the "Basic check" portion of the test plan again to verify if the diagnosis was correct and the vehicle condition has been rectified.
1301142018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. N47T and N57T Diesels with SCR Efficiency Faults Stored. A. The Service Engine Soon lamp is on (MIL) with either or both of the following SCR efficiency faults stored in the DDE: 26F500 - SCR system, efficiency: Efficiency too low 26F600 - SCR system, efficiency: Efficiency too low B. In addition, a Check Control message of "Incorrect diesel exhaust fluid" may be displayed with "no start scenario countdown" active. This would cause any of the following additional faults to be stored, depending on the SCR system status at the time. 2C4E00 - SCR system: System error and poor urea/water mixture quality detected 26FD00 - Reducing agent metering, long-term adaptation: Adaptation value too high 29FB00 - SCR system, warning and deactivation scenario: Warning level 1 29FC00 - SCR system, warning and deactivation scenario: Warning level 2 CAUSE Unfavorable DDE software
1229142018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. Reduced Engine Performance. When driving with high outside ambient temperatures, repeated stop and go, or high-load operation over longer distances, the engine performance can be reduced. The air-conditioning system blower output may also be reduced, and in some circumstances, the compressor is switched off. One or both of the following faults are stored in the DME: 1A2108: Electric fan, self-diagnosis, interval stage 1: Minor fan fault 241400: Electric fan, diagnosis feedback 1: Fan slightly stiff The Service Engine Soon lamp (MIL) would not be illuminated in these situations. 1. A DME software error in the control of the 600W electric fan over-boost or high speed function 2. The electric cooling fan design was not robust enough for continuous over-boost or high-speed operation.
6503132018-11-26. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT. Headunit-Basic: All CD Tracks Are Displayed as "track 0" After Restart. INFORMATION Do not replace parts and do not perform a repair attempt! Note: The issue is rectified after a different CD is inserted into the in-dash CD drive. Explain to the customer that this only happens when the vehicle is turned off with CD mode active. This Service Information will be updated as soon as a solution is available. Software solution is expected to be available with ISTA/P 2.50.1 in July 2013. New integration level: F020-13-07-501 or higher WARRANTY INFORMATION Not applicable.
6502132018-11-26. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Headunit-Basic Does Not Start Up and "BMW" Is Permanently Displayed. The Headunit-Basic (HU-B), also called Radio Professional or the ENTRY head unit, does not start up and "BMW" is permanently displayed on the CID (Central Information Display). No fault code is stored in the head unit. Hardware issue in the HU-B
6201132018-11-26. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. All Gauges and Displays in Instrument Cluster Inoperative. All gauges and displays in the instrument cluster are inoperative, including the following: * Speedometer * Revolution counter * Fuel gauge * Engine oil temperature * No check control messages displayed ??No board computer information displayed Note: A power cycle does NOT rectify the issue. Software error in the instrument cluster
3401132018-11-26. Service bulletin. SERVICE BRAKES. MErroneous "Service due" Message Though Brake Lining Thickness Sufficient. The CBS data calculated for the remaining distance of the front and/or rear brake pads does not agree with the actual brake pad thickness. The yellow brake lining service due indicator illuminates even though the pad thickness is greater than the minimum wear limit (approximately 3.7 mm); the brake wear sensor has not yet been activated (from a thickness of approx. 4.2 mm). In some cases, the red warning message may already be active. The CBS front/rear brake display is based on a mathematical calculation. Various influences are incorporated into this calculation (for example, vehicle speed, brake pressure, and rotor temperature). Due to changing driving characteristics and/or unfavorable environmental conditions, the calculated remaining distance may differ from actual pad thickness.
3201122018-11-26. Service bulletin. STEERING. Teile Clearing for Steering Systems.
1224122018-11-26. Service bulletin. ENGINE. N20 and N26 Engine: DME FC CDA904 FA CAN Message State Trailer 0x2E4 Is Missing.
1222122018-11-26. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE; POWER TRAIN. Service Action: Program Control Units. When coming to a stop, there is the possibility of an unfavorable judder. This is due to the software parameters for downshifting and transmission clutch control. CAUSE Unfavorable vehicle software
1110122018-11-26. Service bulletin. ENGINE. ?N20 Engine: Repeated Juddering or Surging While Accelerating. The vehicle judders or surges repeatedly while accelerating in hot ambient temperatures between 3,000 RPM and 5,000 RPM. The Service Engine Soon lamp is not illuminated, and no fault codes are stored in the vehicle memory related to this complaint. CAUSE The EPDW (electropneumatic pressure convertor) for the turbocharger wastegate valve is binding internally.
1120142018-11-26. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). Delivery Stop: Crankcase Failure. A Delivery Stop has been issued on certain 2015 model year vehicles with N20/N26 engines produced from September 4, 2014 through October 21, 2014. These vehicles may have a crankcase failure. Approximately 145 vehicles are affected.
1114142018-11-26. Service bulletin. ENGINE. Engine Damage Due to Debris in Oil Passages. After performing extensive engine repairs (e.g., cylinder head removal), the engine begins to knock and may lose power. Debris has entered the engine oiling passages during cleaning of the engine block and cylinder head mating surfaces during engine repair.
B6126172018-11-26. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Charging of the high voltage battery is interrupted and will not complete. A change in the job structure in ISTA causes the BDC to open the 30B relay unexpectedly.
B6125172018-11-26. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. SME - HV BATTERY CELL MODULE VOLTAGE FAULTS. When diagnosing with ISTA or ISTA Next, a fault code (detailed below), regarding the cell voltage measurement, is entered in the battery management electronics (SME). ? 21F0C2 - High-voltage battery, cell supervision circuit 1: Voltage measurement (battery cell), line disconnection ? 21F0C3 - High-voltage battery, cell supervision circuit 2: Voltage measurement (battery cell), line disconnection ? 21F0C4 - High-voltage battery, cell supervision circuit 3: Voltage measurement (battery cell), line disconnection ? 21F0C5 - High-voltage battery, cell supervision circuit 4: Voltage measurement (battery cell), line disconnection ? 21F0C6 - High-voltage battery, cell supervision circuit 5: Voltage measurement (battery cell), line disconnection The customer might not have reported the situation as the fault code could have no effect on the vehicle operation. Erroneous fault in the fault memory of the SME, possible fault in a cell supervision circuit (CSC) or a cell module.
B6124172018-11-26. Service bulletin. STEERING: STEERING WHEEL/HANDLE BAR; ELECTRICAL SYSTEM. "?STEERING WHEEL BUTTONS DO NOT FUNCTION RELIABLY. ? Sporadic or continuous malfunction of multifunction steering wheel buttons ? CC Message ""Cruise control without function"" displayed ? Sporadic or continuous malfunction of shift paddles Frictional corrosion on connector line (wiring harness) between switch cluster and steering wheel"
B4103162018-11-26. Service bulletin. STRUCTURE:BODY:DOOR. EDGE CORROSION IN THE INNER DOOR JAMB AREA. Corrosion on inner door panels at the following holes and cavity openings: ? Door brake (1). ? Door wiring harness pass-thru (2).
6609142018-11-13. Service bulletin. ELECTRICAL SYSTEM; LATCHES/LOCKS/LINKAGES:TRUNK LID:LOCK. Unlocking Trunk with Remote Unlocks All Doors. After programming the vehicle with ISTA/P 2.47.1, unlocking the trunk with the remote changes to unlocking all the doors. An application error occurred after programming the vehicle to the Personal Profile Setting (PIA) in the Front Electronic Module (FEM).
6103142018-11-13. Service bulletin. ELECTRICAL SYSTEM. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: z 213901 - Power management: Reduction or shutdown of individual electrical consumer z 8040BD - Reset or deactivation of Terminal 30F z 8040B9 - De-activation of terminal 30B: Top start capability limit reached z 8020E8 - Reset or deactivation of terminal 30F z 800E89 - FRM: start capability limit reached with lights active during stationary mode z 93076B - Deactivation of terminal 30B: upper start capability limit reached z 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active z 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active z 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE z The check control message (ID 229) is caused by a heavily discharged battery. z The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). z In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. z Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. z The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
5131142018-11-13. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS. Headlight Cleaning System: Functional Operation Change. The customer complains that the headlight cleaning system is not working properly and only works after several actuating attempts. CAUSE The "functional" operation of the headlight cleaning system was changed with integration level F020-14-07-500. The functional changes to the headlight cleaning system's operation will occur only after programming the vehicle with ISTA/P 2.53.0 or higher. INFORMATION The headlight cleaning system is no longer activated with the first stalk activation when the lights are on. The functional programming change now requires the stalk to be activated four times before headlight cleaning is activated. The change prevents automatic activation of headlight cleaning when the customer only wants to clean his/her windshield. This is normal operation and no parts should be changed.
7102142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; EQUIPMENT:OTHER:LABELS. Service Action: Replace Emission Label. Certain 2015 model year vehicles with N47T and N57T diesel engines were produced with an "emissions" label which contains incorrect information pertaining to the 2015 model year. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at VDCs will be repaired prior to dealer delivery.
6516142018-11-13. Service bulletin. EQUIPMENT:ELECTRICAL. Central Information Display Intermittently Dimming or Flashing Off/On. Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID.
6406132018-11-13. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. A/C Cooling: Intermittent Reduction of Air Flow. The customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than one hour. The complaint can vary due to one or more of the following variables: * High outside ambient temperature * Too much humidity * A/C temperature and fan settings set too low for too long Note: It is very difficult to duplicate this issue due the required outdoor weather conditions and length of driving time needed. CAUSE Evaporator starts to freeze up due to the position of the evaporator temperature sensor.
6202142018-11-13. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT ADAPTIVE/MOBILITY. Head-Up Display Inoperative. The Head-up Display is inoperative. Fault code 0xB7F6E3 - HUD: Communication error (HUD does not answer) is stored in the Instrument Cluster (KOMB25). A software error in the instrument cluster prevents the Head-up Display from activating.
6120142018-11-13. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM:STARTER ASSEMBLY. Vehicle Only Starts when Remote Key Held Against Column. The vehicle does not start using the Comfort Start feature. The vehicle does start once the remote key is held next to the steering column emergency start area (key symbol at the right side of the column between the white marks). The antenna (aerial) in the passenger compartment near the front of the center console has shorted wiring.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.