Service bulletins for the 2009 Audi S5
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
435 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| A191341 2025303- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 13-35 dated March 25, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
|---|---|
| A241349 2033885- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:SOFTWARE. When the engine is first started in warm ambient temperatures, the idle may fluctuate when the vehicle is put into gear. There is an issue with the engine control module (ECM) software. |
| A301318 2028229- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Supersedes Technical Service Bulletin Group 30 number 11-11 dated December 9, 2011. Customer may report that the vehicle does not start or only starts when the clutch pedal is pressed very firmly. The message ?Press clutch pedal to start vehicle? may appear in the instrument cluster. There may be clutch mechanism wear. |
| A431319 2034162- | 2017-11-17. Service bulletin. SUSPENSION. The adaptive damping suspension control module, J250, cannot be coded via SVM spec/actual after it has been replaced. A new generation of the adaptive damping suspension control module, J250, was placed into production. The new generation control module must be coded and parameterized using an SVM code, which is listed in the attached ETKA Parts Bulletin, 9-119. This parts bulletin can be found in the ETKA Remarks for the part number. |
| A461341 2027636- | 2017-11-17. Service bulletin. SERVICE BRAKES, HYDRAULIC. Supersedes Technical Service Bulletin Group 46 number 13-30 dated March 13, 2013. Brakes on vehicles produced before September 3, 2012 (calendar week 36 of 2012), squeak or squeal when used with light to moderate force. |
| A871237 2020124- | 2017-11-08. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 87 number 12-32 dated September 5, 2012. Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C Pressure/Temperature Sensor G395 leaks refrigerant. This causes Sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the J519 Central Electrics Control unit to Sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Audi Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of Vehicle Electrical System Control Module J519. Vehicle Electrical System Control Module J519 transfers the information provided by the sensor via the comfort data bus to Climate Control Module J255. |
| A011255 2030192- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. MIL light on. P2015 sender of intake manifold flap position/air flow control, implausible signal P2020 sender of intake manifold flap position, intake manifold flap 2, implausible signal. Engine may have reduced performance without significant loss of power or stalling. Check service history to see if the improved ? B? suffix V157 Intake Flap motor has already been installed previously; if yes, only replace the potentiometer seals as described below. The fault entry is made because a linkage of the intake manifold flap adjustment sticks. This is caused by deformed oil seal behind the potentiometers. |
| A011257 2028344- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 01 number 12-51 dated July 18, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300°C (572°F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperature of the exhaust gas and of the catalyst increases quickly. The afterburning in the exhaust manifold before catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase the engine has increased idle speed, may have increased vibrations, and a different sound characteristic. Depending on conditions the time of the catalyst heating phase varies. |
| A171232 2018550- | 2017-11-08. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 17 number 12 - 31 dated August 30, 2012. Oil consumption measurement - Repair Authorization (CA). In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner's Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. |
| A911263 2021151- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Supersedes Technical Service Bulletin Group 91 number 11 ? 83 dated April 15, 2011. The customer may report that the illumination of the dash insert, the air conditioning control panel or the inside light flickers when briefly pressing the accelerator in P or N or when shifting down while driving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off and the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly increased voltage, and the lights mentioned above may briefly flicker. This characteristic is caused by the alternator design and is a normal condition of the vehicle. |
| A941292 2012749- | 2017-11-08. Service bulletin. EXTERIOR LIGHTING. Supersedes Technical Service Bulletin Group 94 number 11-52 dated October 11, 2011. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens. Damp air settles on the inside of a cold lens, which creates condensation. The headlight circulation system allows air from the outside to flow through the headlights. This open waterprotected ventilation system (needed for pressure compensation) creates different climate zones in the headlight: very warm areas, where the lens is warmed up by the light, and relatively cool areas, where the lens is cooled own by the air flow. Considerable differences in humidity and temperature between the inside and the outside of the headlights, even while driving, can lead to condensation. This is especially true in cold and wet weather, but it can also happen after a car wash, after steam cleaning the engine or the front end, with overnight temperature changes, etc. This phenomenon is more visible on lenses made of clear glass than on lenses with patterns. The moisture does not affect the headlight function (light performance) and does not lead to corrosion or other damage to headlight parts. |
| A571281 2020472- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Supersedes Technical Service Bulletin Group 57 number 10-38 dated December 1, 2010. One or more door handle touch sensors cannot be used to unlock the vehicle doors. Through diagnosis it has been determined that a door handle touch sensor must be replaced. Otherwise, the vehicle locks function normally, such as when using the remote key or the interior lock switch. It is possible incompatible door handle touch sensors are installed. This could be due to either the door handle touch sensors or the Central Comfort System control unit J393 (address word 46) having been replaced previously. |
| A901238 2032113- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement. The display will not change faster than 4° F (2° C) per minute. This concept applies to both falling and rising temperatures. A programming strategy is also implemented to avoid incorrect readings on a parked vehicle, due to the temperature sensor being affected by outside influences such as radiant heat from the engine bay, elevated road surface temperatures, etc. |
| A961485 2027416- | 2017-11-08. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. Supersedes Technical Service Bulletin Group 96 number 13-61 dated May 28, 2013. The sunglass holder in the dome light assembly will not latch closed. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure. |
| A911450 2018187- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Supersedes Technical Service Bulletin Group 91 number 13-02 dated August 30, 2013. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices. |
| A461489 2027636- | 2017-11-08. Service bulletin. SERVICE BRAKES, HYDRAULIC. Supersedes Technical Service Bulletin Group 46 number 14-73 dated March 12, 2014. Brakes squeak or squeal when used with light to moderate force. The vehicle was produced before September 3, 2012 (calendar week 36). This bulletin does not apply to vehicles produced on September 3, 2012 or later. For vehicles built on September 3, 2012 or later, use TSB 2034181: 46 Brake noise analysis and handling, or other applicable TSBs. |
| A401441 2018194- | 2017-11-08. Service bulletin. SUSPENSION:FRONT:SHOCK ABSORBER; SUSPENSION:REAR:SHOCK ABSORBER. Supersedes Technical Service Bulletin Group 40 number 13-34 dated September 23, 2013. Oil appears on one or several shock absorbers. |
| A401440 2023187- | 2017-11-08. Service bulletin. STEERING: STEERING WHEEL/HANDLE BAR. Supersedes Technical Service Bulletin Group 40 number 13-35 dated September 23, 2013. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the vehicle is new. The volume and occurrence of the noise will dissipate after a short break-in period. |
| A001467 2002047- | 2017-11-08. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Supersedes Technical Service Bulletin Group 00 number 14-61 dated May 1, 2014. Technician preparation when calling the Audi Technical Assistance Center (TAC). |
| A001466 2037949- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM. |
| A001465 2011732- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. |
| A641433 2029714- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 64 number 12-22 dated July 5, 2012. After one or both of the front door control units (J386/J387) is replaced, one or both of the rear door control units (J3888/J389) cannot be coded or parameterized via an SVM specified vs. actual comparison (spec/actual). The parameter data in the software coding container has changed for the front and rear door control units. As a result, an SVM code is required to update the parameter data for any replacement control unit. Simply running an SVM spec/actual will not code nor update the parameter data in the new replacement control unit. A hardware change suggestion will be provided when an SVM spec/actual is executed. An additional hardware replacement is not required. |
| A441450 2022563- | 2017-11-08. Service bulletin. SUSPENSION; STEERING: STEERING WHEEL/HANDLE BAR. Supersedes Technical Service Bulletin Group 44 number 14-49 dated April 17, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly. |
| A371430 2003658- | 2017-11-08. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY:PEDAL/HAND LEVER(MOTORCYCLE). Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off). No DTCs are stored. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. |
| A001463 2033576- | 2017-11-08. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.