Service bulletins for the 2014 Audi Q7
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1122 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| A941327 2033675- | 2017-12-05. Service bulletin. EXTERIOR LIGHTING:TAIL LIGHTS. Supersedes Technical Service Bulletin Group 55 number 13-31 dated July 18, 2013. The customer may report that the tail lamp lighting does not switch over from bumper to the lid, with lid closed. The rear bumper lights function normally (brake lights, reverse lights, driving lights, turn signals). The center mount brake light functions normally. DTC 03073 (Closed Rear Lid Sensor - Incorrect Signal) may be stored in the comfort system central control module, J393 (address word 46). |
|---|---|
| A941328 2028277- | 2017-12-05. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS. Supersedes Technical Service Bulletin Group 94 number 13-24 dated July 18, 2013. There is considerable moisture present in the headlamp. The moisture disappears only after extended drives (greater than 10 minutes). There is no external damage to the headlamp which could introduce moisture. |
| A971337 2034945- | 2017-12-05. Service bulletin. EXTERIOR LIGHTING:HAZARD FLASHING WARNING LIGHTS; ELECTRICAL SYSTEM. The customer may report two or more warning lights are/were illuminated simultaneously. The warning lights may be sporadic, and may not be illuminated by the time the customer brings the vehicle to the workshop. CAN communication DTCs may be found in control modules. There is sporadic data disruption on the CAN bus wiring behind the dashboard, between the left (T46a) and right (T46b) 46-pin CAN disconnect plugs. |
| Dealer Letter - | 2017-12-05. Service bulletin. ENGINE AND ENGINE COOLING. This communication is to inform you of upcoming Update 24Z6. On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. As a result, the intake manifold flaps do not function and the engine indicator light turns on. Install new manifold actuators. |
| Dealer Letter-Up | 2017-12-05. Service bulletin. ENGINE AND ENGINE COOLING. This communication is to inform you of a revision to Update 24Z6. The revision is in regards to the manifold actuator. |
| Fluid Capacity C | 2017-12-05. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This document contains the fluid capacity chart. |
| Update Bulletin | 2017-12-05. Service bulletin. ENGINE AND ENGINE COOLING. On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. As a result, the intake manifold flaps do not function and the engine indicator light turns on. This Update is in effect until removed. Procedure is valid only for vehicles that show the 24Z6 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. As a result, the intake manifold flaps do not function and the engine indicator light turns on. |
| Update Bulletin | 2017-12-05. Service bulletin. ENGINE AND ENGINE COOLING. On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. As a result, the intake manifold flaps do not function and the engine indicator light turns on. This Update is in effect until removed. On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. As a result, the intake manifold flaps do not function and the engine indicator light turns on. This Update is in effect until removed. Procedure is valid only for vehicles that show the 24Z6 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. As a result, the intake manifold flaps do not function and the engine indicator light turns on. |
| A911396 2026390- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Supersedes Technical Service Bulletin Group 91 number 12-38 dated March 2, 2012. When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes in one of the following scenarios: * After the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), the screen freezes briefly. * After the ignition is switched on (shortly after the phone automatically reconnects with the vehicle). * After the phonebook has downloaded. * When the voice recognition system is used, a message appears in the MMI screen stating that the phone book is too large and that the voice recognition system cannot be used. The command "Call <Name from directory>" is a global MMI command that is available in the telephone menu and main menu screens. If either menu is displayed, the message can appear when the voice recognition button (push to talk) on the steering wheel is pressed. |
| A941320 2028277- | 2017-12-05. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS. Supersedes Technical Service Bulletin Group 94 number 13-11 dated March 6, 2013. There is considerable moisture present in the headlamp. The moisture disappears only after extended drives (greater than 10 minutes). There is no external damage to the headlamp which could introduce moisture. Humid air settles on the inside of the glass, causing moisture to appear on the inside of the headlamp lens. Because of the headlamp circulation system, outside air is allowed to flow through the headlamps. The open, water-protected ventilation system (needed for pressure compensation) creates different "climate zones" inside the headlamp, where the lens is either warmed up by the light or cooled down by passing air. When high air humidity and temperature differences exist between the inside of the headlamps and the outside, condensation can form on the inside of the lens, especially in cold and wet weather. This moisture buildup can happen, for example, after a car wash, after steam cleaning of the engine or the front end, or after overnight temperature changes. This condition is more easily visible with headlamps made from clear glass. The moisture is an optical condition which does not affect the headlamp function (light performance) and does not lead to corrosion or damage of the internal headlamp parts. This condition is common to all exterior vehicle lights, and can occur on every headlamp, fog lamp, or rear lamp. |
| A941323 2033675- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM:WIRING: REAR COMPARTMENT/TRUNK; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 94 number 13-17 dated May 22, 2013. DTC 03073 (Closed Rear Lid Sensor - Incorrect Signal) may be stored in the comfort system central control module, J393 (address word 46). In order for the vehicle to receive a proper rear lid status signal when the lid is operated, the paddle switches on the rear sill trim must contact the opposing lid latch points uniformly. When the rear lid is opened, the paddle switches change state and the comfort system central control module 2, J773, will read G525 and G526. It will then communicate to the comfort system central control module, J393. |
| A941324 2028277- | 2017-12-05. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS. Supersedes Technical Service Bulletin Group 94 number 13-20 dated July 3, 2013. There is considerable moisture present in the headlamp. The moisture disappears only after extended drives (greater than 10 minutes). There is no external damage to the headlamp which could introduce moisture. |
| A961367 2019260- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 96 number 12-37 dated June 11, 2012. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer's door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 Model Years 2005 - 2006 and A3 Model Year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer's HomeLink® opener system is using an alternate code. The handheld transmitter's programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal. |
| A961370 2034736- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL. The garage door opener cannot be programmed. The programming mode cannot be activated. The garage door programming cannot be erased. The method for erasing the Homelink programmed button memory is incorrectly described in the owner's manual. The incorrect description in the owner's manual is: "Erasing the buttons" Press and hold both of the outer buttons until the LED (A) turns off completely (about 20 seconds) to erase all of the buttons simultaneously". The correct way to erase the Homelink programming is to press and hold the two outer Homelink buttons, releasing only when the Homelink indicator light begins to flash after approximately 10 seconds. |
| PDI - 2014 Q7 Ch | 2017-12-05. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This document contains the Audi delivery guidelines checklist. |
| A911392 2030947- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone gets the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call assuming the phone is not responding. |
| A551331 2033675- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM:WIRING: REAR COMPARTMENT/TRUNK. DTC 03073 (Closed Rear Lid Sensor - Incorrect Signal) may be stored in the comfort system central control module, J393 (address word 46). In order for the vehicle to receive a proper rear lid status signal when the lid is operated, the paddle switches on the rear sill trim must contact the opposing lid latch points uniformly. When the rear lid is opened, the paddle switches change state and the comfort system central control module 2, J773, will read G525 and G526. It will then communicate to the comfort system central control module, J393. |
| A461347 2034387- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM; PARKING BRAKE. Customer may report sporadically hearing the parking brake being actuated after the vehicle has been switched off. If the customer does not identify the sound as the sound of the parking brake being actuated, he or she may simply complain of hearing noises from the rear brakes. Ignition is switched off. Steering is locked. Park is selected. Parking brake is not engaged. If the electro-mechanical parking brake is not operated for some time, the free play between brake pads and brake discs increases because of normal brake pad wear. The parking brake control unit performs an automatic correction about every 621 miles (1,000 km). On A8 models, the brake pad thickness is also calculated. |
| A441339 2030275- | 2017-12-05. Service bulletin. STEERING. Supersedes Technical Service Bulletin Group 44 number 13-37 dated February 25, 2013. Vehicle pulls - left or right. Steering wheel not leveled or off-center. In some cases both concerns may be reported. the alignment concern is due to outside influence (e.g. accident), this TSB does not apply. |
| A371309 2028715- | 2017-12-05. Service bulletin. POWER TRAIN. Supersedes Technical Service Bulletin Group 37 number 12-40 dated February 28, 2012. Rough gear changes, both when accelerating and when slowing down. There is a rough driving power disruption that occurs sporadically and lasts for less than a second. After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted. |
| A011314 2033919- | 2017-12-05. Service bulletin. POWER TRAIN; ENGINE. MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. |
| A011313 2034359- | 2017-12-05. Service bulletin. ENGINE. MIL on. DTC P20E9 is stored in the engine control module (ECM). In vehicles produced during a certain period, the AdBlue filter seal within the level sensor module may have been damaged during the assembly process. This damaged seal can allow unfiltered AdBlue to be sucked into the delivery system, subsequently damaging the pressure sensor and reducing agent pump V437. |
| A941303 2029194- | 2017-11-17. Service bulletin. EXTERIOR LIGHTING; EXTERIOR LIGHTING:HEADLIGHTS. Supersedes Technical Service Bulletin Group 94 number 12-99 dated November 30, 2012. Only vehicles with Xenon headlights can be affected by this condition. The customer complains the high beams do not function on one side or one of the low beams flickers intermittently. In addition to this, an "Adaptive Headlight Defective" warning can be present in the cluster if the vehicle has the Prestige trim level. One of the following DTCs are set in the 09 - Central Electric Control Unit or in the 55 - Headlamp Range Control Unit depending on the trim level of the vehicle. Vehicles with the Premium Plus option package can have the DTC set in the 09 module. Vehicles with the Prestige option package can have the DTC set in the 55 module. One or more of the connectors inside the headlamp housing are disconnected fully or partially from the factory. |
| A911374 2024323- | 2017-11-17. Service bulletin. BACK OVER PREVENTION: CAMERA SYSTEM. Supersedes Technical Service Bulletin Group 91 number 12-61 dated October 1, 2012. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions. |
| A571384 2024463- | 2017-11-17. Service bulletin. LATCHES/LOCKS/LINKAGES; EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 57 number 12-72 dated September 24, 2012. Keyless entry is inoperative. Remote range is poor. Audi Advanced key is inoperative. High early warranty information related to inoperative remote keys necessitates this repair authorization. Through our combined efforts and cooperation, we will be able to raise the level of Audi quality and overall customer satisfaction. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.