WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Audi Q7

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1122 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
A441343 2030194-2017-10-31. Service bulletin. STEERING. Supersedes Technical Service Bulletin Group 44 number 13-41 dated September 26, 2013. Complaints of steering wheel vibration and/or steering wheel oscillation at a speed range of 55 - 80 mph (88 - 128 km/h), on vehicles with very low mileage or at PDI. The condition does not result in any handling concerns or loss of vehicle control. Vehicles have original factory-installed wheels and tires.
A261320 2026757-2017-10-31. Service bulletin. EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 26 number 11-03 dated June 29, 2011. There is an AdBlue-related message displayed in the instrument cluster. MIL may or may not be illuminated.
A171347 2035463-2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 17 number 13-44 dated October 22, 2013. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, and the ambient temperature and road conditions. Additional factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Utilizing the advanced sensor technology integrated in models equipped with the 3.0 TFSI engine, it is possible to measure oil consumption electronically via a Guided Function test plan. If the electronic oil consumption test is not available for this model, perform the test with the conventional scale/oil weighing method. See TSB 2018550 for instructions for the conventional scale/oil weighing method.
A011340 2035519-2017-10-31. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 01 number 13-38 dated October 23, 2013. MIL on. DTCs are stored in the engine control module (ECM). Drivability is not affected. The leak detection pump (LDP) is a vacuum-driven, ECM-controlled, diaphragm pump. In order for the LDP to operate, the engine must be running and vacuum must be applied to the vacuum switch on the LDP. The LDP pressurizes the EVAP system and monitors any pressure drop within a specified amount of time in order to detect a leak. DTC P0456 or DTC P0442 can be stored due to static or sporadic air leaks in the EVAP system or static or sporadic air leaks in the LDP.
A001357 2035669-2017-10-31. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. Supersedes Technical Service Bulletin Group 00 number 13-56 dated November 1, 2013. There are special service instructions to be performed on all Model Year 2014 A6, A7, Q5, and Q7 vehicles before the vehicles are delivered to customers. When performing PDI inspections on vehicles delivered from November 2013 - February 2014, please prepare the vehicles for delivery with a special focus on the areas listed in this bulletin. These checks can be performed during the normal PDI inspection process.
A001356 2035669-2017-10-31. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. There are special service instructions to be performed on all Model Year 2014 A6, A7, Q5, and Q7 vehicles before the vehicles are delivered to customers. When performing PDI inspections on vehicles delivered from November 2013 - February 2014, please prepare the vehicles for delivery with a special focus on the areas listed in this bulletin. These checks can be performed during the normal PDI inspection process.
QRSB-2014 Audi Q2017-10-31. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This document contains the quick reference specification book.
Reference-Audi M2017-10-31. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; TIRES. This document contains the Audi normal load condition tire pressure table. This document is in Spanish.
PDI-2014 Q7 TECH2017-10-31. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This document contains the Audi technician report checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Audi recommends using an Audi approved battery charger to prevent excessive battery discharge during inspection. This document is in Spanish.
PDI-2014 Q7 DELI2017-10-31. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This document contains the Audi delivery report checklist. This document is in Spanish.
PDI-2014 ALL MOD2017-10-31. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This document contains the Audi vehicle condition checklist. This document is in Spanish.
A941330 2028277-2017-10-31. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS. Supersedes Technical Service Bulletin Group 94 number 13-28 dated August 13, 2013. There is considerable moisture present in the headlamp. The moisture disappears only after extended drives (greater than 10 minutes). There is no external damage to the headlamp which could introduce moisture. Humid air settles on the inside of the glass, causing moisture to appear on the inside of the headlamp lens. Because of the headlamp circulation system, outside air is allowed to flow through the headlamps. The open, water-protected ventilation system (needed for pressure compensation) creates different ?climate zones? inside the headlamp, where the lens is either warmed up by the light or cooled down by passing air. When high air humidity and temperature differences exist between the inside of the headlamps and the outside, condensation can form on the inside of the lens, especially in cold and wet weather. This moisture buildup can happen, for example, after a car wash, after steam cleaning of the engine or the front end, or after overnight temperature changes. This condition is more easily visible with headlamps made from clear glass. The moisture is an optical condition which does not affect the headlamp function (light performance) and does not lead to corrosion or damage of the internal headlamp parts. This condition is common to all exterior vehicle lights, and can occur on every headlamp, fog lamp, or rear lamp.
A661339 2035673-2017-10-31. Service bulletin. VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR; STRUCTURE. Supersedes Technical Service Bulletin Group 66 number 13-38 dated November 15, 2013. Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. After diagnosis, it is determined that the source of the wind noise is the exterior rear view mirrors. The two main sources of wind noise from the exterior rear view mirrors are: the seam surrounding the turn signal lamp and the seam at the mirror base. The modifications explained in the Service section of this bulletin will effectively mitigate the wind noise symptom for the customer.
A441346 2010334-2017-10-31. Service bulletin. WHEELS:LUGS/NUTS/BOLTS/STUDS; WHEELS. Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012. Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc., and should not be used to apply torque to wheel bolts. Always use a calibrated torque wrench to attain the correct wheel bolt torque and follow the proper wheel tightening procedure as outlined in Elsa. Proper use of a calibrated torque wrench ensures that all wheel bolts are tightened equally and reduces the chances of repeat repairs. Using methods other than a calibrated torque wrench to attain correct wheel bolt torque may lead to problems.
A441345 2030194-2017-10-31. Service bulletin. WHEELS; TIRES. Supersedes Technical Service Bulletin Group 44 number 13-43 dated November 1, 2013. Steering wheel vibration and/or steering wheel oscillation at a speed range of 55 - 80 mph (88 - 128 km/h) on vehicles with very low mileage or at PDI. The condition does not result in any handling concerns or loss of vehicle control. Vehicles have original factory-installed wheels and tires. Tire pressures on Audi vehicles are set to specified values in order to prevent flat spotting during the transportation process from various Audi plants to United States ports. To closely monitor complaints of tire-related vibration at very low mileage, we are asking that you contact the Audi Technical Assistance Center (TAC) before performing any repairs on vehicles with this condition.
A371319 2036113-2017-10-31. Service bulletin. ENGINE; ELECTRICAL SYSTEM. The ignition key cannot be removed even though the gear shifter is in Park (P). The vehicle is mechanically in the Park position, but this is not recognized electronically. The gear shifter cannot be moved from the Park position. On vehicles with advanced key, the vehicle cannot be locked by remote control after the engine has been switched off. DTC may be sporadically stored in the vehicle authorization system control module. The Park position of the gear shifter is sporadically not recognized, which causes the ignition key to not be cleared and prevents the vehicle from being locked.
A201430 2035591-2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER. Customer reports hearing noises from the rear of vehicle or from fuel tank area. Normal fuel system pulsation can cause slight vibrations in the pressure regulator on the flange located on the right side of the fuel tank. This pulsation also causes the long, curved fuel lines to vibrate and make a jarring noise in the tank.
A911308 2028190-2017-10-31. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Supersedes Technical Service Bulletin Group 91 number 11-28 dated December 9, 2011. Customer is inquiring about retrofitting the MMI system with a language pack or map database outside of factory-available options.
A911307 2030465-2017-10-31. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Supersedes Technical Service Bulletin Group 91 number 13-98 dated August 5, 2013. MMI 3G+ Sound system "popping" and various other technical Issues (K0715 Update). This bulletin only applies to vehicles with Navigation Plus (PR Number 8DY). The applicable vehicles can be clearly identified by the SIM card slot on the faceplate of the front MMI mainunit.
A911304 2013422-2017-10-31. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.
A901341 2010353-2017-10-31. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. Supersedes Technical Service Bulletin Group 90 number 10-14 dated August 10, 2010. Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release once the heating process has completed. As a result, the socket can become inoperative when used as a power outlet.
A801305 2033806-2017-10-31. Service bulletin. ELECTRICAL SYSTEM:WIRING. Supersedes Technical Service Bulletin Group 80 number 13-04 dated August 9, 2013. Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. ?Limp Home? mode is active. Faults are stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector as shown in the illustration. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant.
A721309 2035357-2017-10-31. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Seat memory function does not work. DTCs are stored. In the event of a voltage fluctuation in the vehicle power system, the software of the seat adjustment module fails.
A661334 2029586-2017-10-31. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 66 number 13-32 dated September 26, 2013. The customer may report hearing wind noise while driving at highway speeds. The noise may occur on either side of the vehicle. Wind noise may be coming from either the mirror base or the lane change assist lamp. Improved parts are available.
A661333 2033517-2017-10-31. Service bulletin. VISIBILITY. Supersedes Technical Service Bulletin Group 66 number 13-27 dated April 8, 2013. Wind noise is heard by the customer at highway speeds. Air flows through the exterior rear view mirror housing at the seam where the turn signal lamp meets the housing. This causes a high-frequency whistling tone.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.