Service bulletins for the 2014 Audi Q5
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1389 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Electrical system are shown. Show all
| A911431 2023006- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM:WIRING. Supersedes Technical Service Bulletin Group 91 number 11-08 dated August 22, 2011. The parking aid system does not work. DTCs may be logged in parking aid control unit for disruption/short circuit to ground. The wire harness for the parking aid system may have been damaged when the front license plate frame was installed. |
|---|---|
| A271424 2025360- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Supersedes Technical Service Bulletin Group 27 number 12-12 dated February 28, 2012. Customer may report that the vehicle does not start due to a discharged battery. The vehicle has either a battery diagnostic management control module or a battery energy management control module. This TSB provides basic diagnosis steps for discharged batteries, general tips for working with batteries, and system verification steps to ensure that the vehicle is configured correctly. |
| A171449 2028440- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Supersedes Technical Service Bulletin Group 17 number 12-26 dated January 20, 2012. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer. |
| A971442 2036764- | 2017-11-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 97 number 14-41 dated March 18, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system, including: P056200, P057100, P068700, P068A00, P162400, P190C00, U010000, U010100, U012100, U014600, U015500, U021200, U101100, U102600, U111100, U111300, U140000, VAG00003, VAG00185, VAG00263, VAG00317, VAG00384, VAG00446, VAG00456, VAG00457, VAG00466, VAG00473, VAG00532, VAG00565, VAG00591, VAG00714, VAG00819, VAG00955, VAG01217, VAG01299, VAG01314, VAG01315, VAG01317, VAG01320, VAG01330, VAG01331, VAG01332, VAG01334, VAG01333, VAG01336, VAG01705, VAG01964, VAG02067, VAG02072, VAG02095, VAG02103, VAG02203, VAG02214, VAG02635, VAG02812, VAG02874, VAG03041, VAG03157, VAG03166, VAG03220, VAG03278, and/or VAG03531. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly. |
| A971441 2036764- | 2017-11-08. Service bulletin. ENGINE; ELECTRICAL SYSTEM. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly. |
| A941434 2036670- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING:HEADLIGHTS. The high beam is inoperative on one side of the vehicle. The low beams operate correctly. A warning may appear in the instrument cluster. DTCs may be present in the central electrics control module, J519 (address word 09). The connection for the high beam shutter is not connected in the affected headlight. |
| A911427 2036575- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently in vehicles with MMI3G+ Navigation, and in vehicles with or without Audi connect. Intermittently, the MMI system does not appear to remember that the user's myAudi PIN has already been entered, and it requires the user to enter the PIN again in vehicles with Audi connect. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is paired to the vehicle, those addresses and contacts will only be visible any time that the same phone is paired to the vehicle. Any time that the same phone is not paired to the vehicle, the addresses and contacts will not be available. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is not paired to the vehicle, the addresses and contacts will be available any time. In vehicles with Audi connect, the user is prompted to enter the myAudi PIN when selecting online destinations or when importing contacts from the myAudi account. If the user?s Bluetooth phone (the same phone that was paired to the vehicle when the PIN was entered initially) is paired to the vehicle, the user will not be prompted to re-enter the PIN after it has been entered. |
| A941432 2017806- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING:BACK UP LIGHTS. Supersedes Technical Service Bulletin Group 94 number 13-19 dated May 23, 2013. The light bulb warning light is displayed in the instrument cluster with the ?Vehicle lights: malfunction? message. DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 or DTC 01800 are changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTCs are automatically cleared. |
| A911419 2026895- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 91 number 11-16 dated October 5, 2011. During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle. |
| A201431 2035073- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; ENGINE. Supersedes Technical Service Bulletin Group 20 number 13-28 dated November 14, 2013. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the ECM. Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak. |
| A011463 2033630- | 2017-11-08. Service bulletin. ENGINE; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 01 number 13-86 dated April 15, 2013. The MIL is on. There is a rough idle. DTCs are stored in the ECM. Engine may have reduced performance without significant loss of power or stalling. Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced. |
| Update Bulletin | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM. Under certain conditions, permanent mode $0A DTC codes concerning the fuel pump power stage module may remain visible after the vehicle?s OBD system has run the proper monitors successfully to allow the DTC to be erased by the system, after a proper repair. This software malfunction may cause vehicle to not pass IM inspection programs. This software update eliminates specific permanent DTC codes stored in mode $0A of the ECM. All other DTC storage functions remain unaffected. This Update is in effect until removed. |
| Update Bulletin | 2017-11-03. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:SOFTWARE. Under certain conditions, permanent mode $0A DTC codes concerning the fuel pump power stage module may remain visible after the vehicle?s OBD system has run the proper monitors successfully to allow the DTC to be erased by the system, after a proper repair. This software malfunction may cause vehicle to not pass IM inspection programs. This software update eliminates specific permanent DTC codes stored in mode $0A of the ECM. All other DTC storage functions remain unaffected. This Update is in effect until removed. Procedure is valid only for vehicles that show the 24AD code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the Federal Emissions Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. |
| Dealer Letter - | 2017-11-03. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM. This communication is to inform you of upcoming Update 24AD. Under certain conditions, permanent mode $0A DTC codes concerning the fuel pump power stage module may remain visible after the vehicle?s OBD system has run the proper monitors successfully to allow the DTC to be erased by the system, after a proper repair. This software malfunction may cause vehicle to not pass IM inspection programs. This software update eliminates specific permanent DTC codes stored in mode $0A of the ECM. All other DTC storage functions remain unaffected. Update the ECM software to latest levels via SVM. |
| A201328 2035073- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 20 number 13-27 dated October 16, 2013. MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. |
| A911317 2035919- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). GPS inaccuracies can be caused by several different factors. If it is unclear if this PSS applies, submit a Technical Assistance Center ticket for additional instruction. Perform Spec Actual and attach the GFF log to the ticket. Customer states the navigation system is not tracking the vehicle correctly. No DTCs related to the GPS antenna or MMI system are present. The issue occurs after the vehicle is parked overnight or for several hours in a parking garage or other similar enclosed space. A private home garage does not apply. The issue does not occur if the vehicle is parked overnight or for several hours in an open-sky environment. The condition continues for the duration of the drive. The issue only corrects itself with a 3-finger reset or during a vehicle sleep cycle. The vehicle is not a Q7 or A8. If the above conditions apply and the customer vehicle is a Q7 or A8, submit a Technical Assistance Center ticket for additional instruction. Perform Spec Actual and attach the GFF log to the ticket. |
| A571398 2035173- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM; LATCHES/LOCKS/LINKAGES:DOORS:LATCH. Supersedes Technical Service Bulletin Group 57 number 13-96 dated October 16, 2013. Customer may report that the automatic door lock function cannot be deactivated. The "Lock when driving" (Autolock) configuration setting has been discontinued starting in some model year 2013 vehicles, and it is no longer available in the Car >> Vehicle Settings category in the MMI. The vehicle can still be unlocked while it is being driven, at any time, with the central locking switch in the door. |
| Dealer Letter - | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM. This communication is to inform you of that Update 48K8 has been revised to include a warning to ensure that the Bluetooth function of the scan tool must be physically switched off prior to performing this Update. The revised Update will be visible in ElsaWeb and ServiceNet on or about September 27, 2013. Please ensure your technicians are made aware of this new information. |
| A911304 2013422- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present. |
| A801305 2033806- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM:WIRING. Supersedes Technical Service Bulletin Group 80 number 13-04 dated August 9, 2013. Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. ?Limp Home? mode is active. Faults are stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector as shown in the illustration. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant. |
| A721309 2035357- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Seat memory function does not work. DTCs are stored. In the event of a voltage fluctuation in the vehicle power system, the software of the seat adjustment module fails. |
| A661334 2029586- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 66 number 13-32 dated September 26, 2013. The customer may report hearing wind noise while driving at highway speeds. The noise may occur on either side of the vehicle. Wind noise may be coming from either the mirror base or the lane change assist lamp. Improved parts are available. |
| A571393 2035173- | 2017-10-31. Service bulletin. LATCHES/LOCKS/LINKAGES; ELECTRICAL SYSTEM. Customer may report that the automatic door lock function cannot be deactivated. The ?Lock when driving? (Autolock) configuration setting has been discontinued starting in some model year 2013 vehicles, and it is no longer available in the Car >> Vehicle Settings category in the MMI. The vehicle can still be unlocked while it is being driven, at any time, with the central locking switch in the door. |
| A011332 2035368- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM; ENGINE. MIL on. DTC P203B00 (Reductant Level Sensor Circuit Range/Performance) is stored in the engine control module (ECM), J623 (address word 01). Due to a production issue for the level sensor, the ECM cannot correctly read the Reductant (AdBlue) fluid level. |
| A691326 2023323- | 2017-10-31. Service bulletin. AIR BAGS; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 69 number 12-25 dated April 25, 2012. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. An SVM code is required to code and parameterize the new service replacement airbag control module. Each model?s SVM code is provided in a parts bulletin (GP bulletin), which should have been referenced through ETKA when the module was replaced. The control module cannot be coded until the SVM code has been executed. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.