Service bulletins for the 2013 Audi A8
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1506 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Electrical system are shown. Show all
| A271421 2036392- | 2017-12-14. Service bulletin. ELECTRICAL SYSTEM. Vibrations are felt at 1000 rpm and 3000 rpm. DTCs are stored in the subframe mount control module. The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is programmed). As a result, the vehicle vibrates or judders when cylinders are actively switched off. |
|---|---|
| A001459 2029737- | 2017-12-14. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 00 number 12-34 dated June 6, 2012. The process of draining oil through the drain plug is not always tidy. When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints. |
| A011397 2030580- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 01 number 13-94 dated May 8, 2013. The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs may be present. The remote key being used is transmitting incomplete immobilizer information to the vehicle; resulting in the condition. |
| A011394 2030580- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 01 number 12-60 dated December 7, 2012. The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs may be present. The remote key being used is transmitting incomplete immobilizer information to the vehicle; resulting in the condition. |
| A011387 2033726- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM. The MIL may illuminate. DTCs are stored in the engine control module (ECM) . In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. DTCs are stored in the transmission control module (TCM). There is an issue with the ECM and/or TCM software. |
| A201443 2035073- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 20 number 14-41 dated October 9, 2014. MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak. |
| A001470 2039206- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM. High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Audi of America has started to host its TSB videos outside of ElsaPro. Doing so provides higher-quality videos, more reliable access to the videos, and the ability to view the videos on different devices. |
| A911469 2038824- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY:CABLES. The following message appears on the MMI display: ?Device or cable type not supported?. The ?Device or cable type not supported? message may be displayed when the wrong AMI cable type is used. See the Service section of this bulletin for an overview of the AMI cables that support iOS devices. |
| A911461 2033032- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 91 number 13-76 dated February 22, 2013. Call quality using the hands-free function is poor. Additionally, voice-activated functions may be restricted. The driver sounds muffled. The voice of the driver is quiet. The driver?s voice is accompanied by background interference. Voice-activated commands are not recognized. Various malfunctions can result from the normal airflow out of the center instrument panel vents that are directed upward at the microphones in the roof module, and can limit microphone sensitivity. |
| A911463 2028190- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. The customer would like to change the MMI system language to a different language that is not already supported by MMI. When a song is being played and the track information for that song contains foreign language characters, the driver information system (DIS) in the cluster correctly displays the characters, but the MMI display does not. |
| A451409 2038770- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:SOFTWARE. The ESP warning light may be on in the instrument cluster. DTC B200047 (Control unit faulty) is stored in the sensor electronics control module, J849 (address word 3B). With software level 0053, the J849 control module may store DTC B200047 even though the control unit is not faulty. |
| A461357 2031135- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 46 number 12-26 dated October 23, 2012. The yellow warning for electromechanical parking park (EPB) appeared once in the instrument cluster. The warning turned off after the ignition was cycled, and there have not been additional occurrences. EPB function was not affected. The adaptive cruise control (ACC) was inoperative once, but it resumed proper operation after the ignition was cycled, and there have not been additional occurrences. DTCs are logged in the EPB control module. There is an issue with the software in the EPB control module that occurs one time. Because the issue only occurs once, replacing the control module could cause an additional occurrence. |
| A801304 2033806- | 2017-12-05. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ELECTRICAL SYSTEM:WIRING. Supersedes Technical Service Bulletin Group 80 number 13-03 dated May 13, 2013. Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. "Limp Home" mode is active. Faults are stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant. |
| A911392 2030947- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone gets the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call assuming the phone is not responding. |
| A531302 2034404- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM; PARKING BRAKE. Customer may report that the vehicle does not start due to a discharged battery. DTC U101100 (supply voltage too low) is stored in the gateway, J533 (address word 19), and/or the electronic parking brake (EPB) control module, J540 (address word 53). According to the test plan "19-Read Data Bus Keep-Awake Manager", the EPB control module kept the data bus active for prolonged periods of time. The EPB switch appears to be permanently operating (applying or releasing the parking brake) due to an internal mechanical issue or because it is jammed or blocked by debris or by a foreign object. Test plan "19-Read Data Bus Keep-Awake Manager", identifies the EPB control module as keeping the data bus active for prolonged periods of time. |
| A461348 2034404- | 2017-12-05. Service bulletin. PARKING BRAKE; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 53 number 13-02 dated July 11, 2013. Customer may report that the vehicle does not start due to a discharged battery. DTC U101100 (supply voltage too low) is stored in the gateway, J533 (address word 19), and/or the electronic parking brake (EPB) control module, J540 (address word 53). According to the test plan "19-Read Data Bus Keep-Awake Manager", the EPB control module kept the data bus active for prolonged periods of time. The EPB switch appears to be permanently operating (applying or releasing the parking brake) due to an internal mechanical issue or because it is jammed or blocked by debris or by a foreign object. Test plan "19-Read Data Bus Keep-Awake Manager", identifies the EPB control module as keeping the data bus active for prolonged periods of time. |
| A461347 2034387- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM; PARKING BRAKE. Customer may report sporadically hearing the parking brake being actuated after the vehicle has been switched off. If the customer does not identify the sound as the sound of the parking brake being actuated, he or she may simply complain of hearing noises from the rear brakes. Ignition is switched off. Steering is locked. Park is selected. Parking brake is not engaged. If the electro-mechanical parking brake is not operated for some time, the free play between brake pads and brake discs increases because of normal brake pad wear. The parking brake control unit performs an automatic correction about every 621 miles (1,000 km). On A8 models, the brake pad thickness is also calculated. |
| A001351 2031850- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 00 number 13-46 dated March 13, 2013. Engine and ignition shut off when driver's door is opened. Electronic Parking Brake (EPB) activates when driver's door is opened (A6/A7/S6/S7 only). |
| A941306 2017806- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012. Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09). Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 is changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTC is automatically cleared. |
| A911376 2033032- | 2017-11-17. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Call quality using the hands-free function is poor. Additionally, voice-activated functions may be restricted. The driver sounds muffled. The voice of the driver is quiet. The driver's voice is accompanied by background interference. Voice activated commands are not recognized. Various malfunctions can result from the normal airflow out of center instrument panel vents that are directed upward at the microphones in the roof module, which can limit microphone sensitivity. |
| Update Bulletin | 2017-11-17. Service bulletin. LANE DEPARTURE: ASSIST; ELECTRICAL SYSTEM:SOFTWARE. On Audi vehicles with lane change assist manufactured within a specific period, the lane change assist control unit may fail in individual cases after a period of time. The Update is in effect until removed. Procedure is valid only for vehicles that show the 96C8 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicles must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted timeframe stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. |
| A371399 2029027- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Supersedes Technical Service Bulletin Group 37 number 12-77 dated December 19, 2012. Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. DTCs are stored in the transmission control module, J217 (02). If DFCCs do not match exactly, this TSB does not apply. |
| A371302 2029027- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Supersedes Technical Service Bulletin Group 37 number 13-99 dated April 1, 2013. Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. DTCs are stored in the transmission control module (TCM), J217 (02). If DFCCs do not match exactly, this TSB does not apply. The DTCs are stored due to an issue with the transmission control module software. |
| A371301 2028985- | 2017-11-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 37 number 13-97 dated March 4, 2013. Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 (Torque Converter Clutch Circuit Performance) or "Stuck Off" is stored in transmission control module (TCM), J217 (address word 03). The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks. |
| A001346 2031850- | 2017-11-17. Service bulletin. ENGINE; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 00 number 13-44 dated January 17, 2013. Engine and ignition shut off when driver's door is opened. Electronic Parking Brake (EPB) activates when driver's door is opened (A6/A7/S6/S7 only). |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.